To address the limited output performance and low energy conversion efficiency of conventional vibration energy harvesters (VEHs) under varying ambient frequencies. A broadband dual-resonant VEH incorporating tunable planar spring mechanism is proposed for efficient energy scavenging from wind-induced vibrations of overhead transmission line. The frequency modulation mechanism of VEH adopting tunable planar spring with customized angular configuration is first analyzed. A broadband VEH with dual-resonant technique is then developed, and its frequency band broadening mechanism is systematically investigated. A prototype with two sets of planar spring angles of α = 30°/70°, β = 30°/70°, and γ = 30°/70°, and the thickness of h = 0.6/0.7 mm are subsequently fabricated and experimentally validated for the vibration energy harvesting applications in overhead transmission line. The experimental results demonstrate that the proposed VEH achieves optimal output performance at 29 Hz and 48 Hz within the frequency band range of 26–53 Hz where the output power exceeds 50% of peak, covering the vertical vibrations of 110 kV transmission lines within the typical frequency range of 5–50 Hz induced by the Karman vortex effect, yielding an open-circuit peak-to-peak voltage of 9.3 V and two peak powers of 81.3 mW and 84.5 mW at the two resonant frequencies of 29 Hz and 48 Hz, with a total power density of 1.29 mW·cm−3·g−2 under external excitation vibration maintained at 100 μm and a fixed load of 2000 Ω.
Open-phase faults (OPFs) seriously degrade the reliability of dual three-phase permanent magnet synchronous motor (DTP-PMSM) drives. Existing methods mainly diagnose first faults from healthy operation, while secondary OPFs during fault-tolerant control (FTC) are less addressed. This paper proposes a unified diagnosis and FTC scheme for multi-degree OPFs. Based on vector space decomposition, harmonic-subspace current variation is used for fault detection, and spatial current-vector relationships locate the faulty phase or winding set. The scheme covers single-phase, two-phase, three-phase winding-set, and sequential OPFs during FTC. Experiments verify accurate localization and stable post-fault operation.
This paper presents 24.0–29.5 GHz bypass and bi-directional amplifiers for phased-array transceiver in 65-nm CMOS. The bypass amplifier operates in amplification or bypass mode. The bi-directional amplifier provides gain in both directions. The proposed amplifiers utilize matching network embedded switches, achieving path-switching while minimizing chip area. The bypass amplifier achieves a gain of 6.0 dB and an OP1dB of 3.4 dBm with −1 dB bandwidth of 22.7–29.5 GHz in amplification mode; a loss of 2.6 dB with −1 dB bandwidth of 15.1–30.6 GHz in bypass mode. The bi-directional amplifier achieves a gain of 5.0 dB and an OP1dB of 3.4 dBm with −1 dB bandwidth of 23.2–29.6 GHz. The core areas of the two amplifiers occupy 0.09 mm2 and 0.10 mm2 respectively.
In the brief, to mitigate fractional spur caused by nonlinearity in phase-locked loops (PLL) system, a 1.1 V, 1.5∼2.5 GHz quadrature fractional-N frequency synthesizer incorporating an enhanced nonlinearity-induced noise performance digital delta-sigma modulator (ENOP-DDSM) is designed and analyzed. The ENOP-DDSM extends the modulator output range, and compared with the conventional multi-stage noise shaping digital delta-sigma modulators (MASH-DDSM), the ENOP-DDSM offers immunity to higher-order system nonlinearity, thereby improving spur performance. Additionally, an automatic amplitude control (AAC) loop is employed to enhance circuit robustness. The proposed prototype, fabricated in 55 nm CMOS technology, consumes 10.6 mW from a 1.1 V supply and occupies an area of 670 × 800 μm2. Measurement results indicate a phase noise of −121.1 dBc/Hz at a 1 MHz offset from the 1.995 GHz carrier, with an integrated root mean square (RMS) jitter of 0.66 ps over 12 kHz to 20 MHz. Notably, compared to the MASH-DDSM, the ENOP-DDSM achieves up to 8.9 dB fractional spur suppression, validating the effectiveness of the proposed nonlinearity-mitigation technique.
In this letter, a dual-frequency reconfigurable negative group delay (NGD) circuit based on the split ring resonator (SRR) is presented. This circuit achieves the reconfigurability of the center frequency and negative group delay peak value for the two operating frequency points by loading varactor diodes and PIN diodes. The proposed dual-frequency circuit is implemented with two serially connected SRR units. Furthermore, the bandwidth can be expanded by adjusting the bias voltages across the active components. Meanwhile, a matching circuit is integrated into the transmission line to optimize the return loss which in turn improves the energy utilization efficiency of the circuit. Through the verification of simulation and measurement, both resonant frequencies of the proposed dual-frequency circuit realize an adjustable operating frequency range from 1.18 GHz to 2.05 GHz with its negative group delay peak value varying within −0.86 and −4.46 ns, |S21| from −4.57 to −7.23 dB and |S11| better than −18.4 dB.
Accurate modeling of electromagnetic scattering characteristics in island-sea composite scenarios is of great significance for improving target detection and identification in marine environments. This paper proposes an island-sea composite scene modeling method by integrating Digital Elevation Models (DEM) with remote sensing imagery. Remote sensing imagery is utilized for land-cover classification to identify different media types, including sea, forest, rock, and city. The corresponding electromagnetic and roughness parameters are then assigned to each discrete facet according to its land-cover category. Based on this framework, an improved two-scale model combining the Advanced Integral Equation Model (AIEM) and Kirchhoff Approximation (KA) is employed to calculate the scattering response. The simulated backscattering coefficients are validated against ALOS-1 PALSAR measurements, and the results demonstrate that the prediction errors for all four land-cover classes are within 1.79 dB.
In this letter, a three-way reconfigurable power divider consisting of a Y-junction, λ/4 transmission lines, and switch elements is proposed. The presented structure employs one switch per branch, with no switch required on the main line and no isolation resistors, thereby minimizing the total number of switches. The switches, including λ/4 transmission lines, serve as an N-selector and impedance matching circuit. To achieve an input return loss greater than 10 dB, the characteristic impedance of the λ/4 line and the number of branches are mathematically determined. Based on the derived results, a three-way reconfigurable power divider with three switches—the minimum possible number—is designed. The measured input return losses and ON-port losses for all transmission states were obtained as 12.01–24.4 dB and 0.24–1.4 dB, respectively, at 2.45 GHz. The ON-OFF port isolations for 1:1 and 1:2 transmission modes were achieved as 45.32 and 24.28 dB, respectively, at 2.45 GHz.
This paper presents a 16-bit, 1-MS/s SAR ADC featuring a bitonic sorting-based capacitor recombination calibration technique. The capacitor recombination calibration exploits inherent device mismatches for mutual compensation, thereby eliminating the need for additional analog circuitry and complex digital computations. By employing a floating-capacitor technique, the calibration algorithm's tolerance to comparator offset voltage and noise is significantly enhanced. Compared to conventional sorting, the adopted bitonic sorting algorithm offers superior time complexity, stronger interference immunity, and reduced hardware overhead. The feasibility of the calibration technique is verified through behavioral-level modeling, and a circuit prototype is implemented in a 180-nm CMOS process. Simulation results demonstrate that the calibration improves the signal-to-noise-and-distortion ratio (SNDR) and spurious-free dynamic range (SFDR) from 85.3 dB and 91.1 dB to 94.1 dB and 108.6 dB, respectively.