軽金属
Online ISSN : 1880-8018
Print ISSN : 0451-5994
ISSN-L : 0451-5994
検索
詳細検索
OR
閲覧
検索
63 巻, 10 号
選択された号の論文の7件中1～7を表示しています
すべての抄録を表示する
    • |<
    • <
    • 1
    • >
    • >|
研究論文
  • 産業用X線トモグラフィ装置による材料欠陥およびミクロ組織の3D可視化
    戸田 裕之, 小林 正和, 久保 貴司, 茂泉 健, 杉山 大吾, 山本 裕介, 原田 俊宏, 林 憲司, 半谷 禎彦, 村上 雄一朗
    原稿種別: 研究論文
    2013 年 63 巻 10 号 p. 343-349
    発行日: 2013/10/30
    公開日: 2013/11/30
    DOIhttps://doi.org/10.2464/jilm.63.343
    ジャーナル フリー
    抄録を表示する抄録を非表示にする
    In the present study, various microstructural features, such as particles and pores, have been visualized in cast and wrought aluminum alloys by employing X-ray tomography apparatuses with a wide range of spatial resolution. Special care is dedicated to evaluate an identical sample for each entire series of imaging experiments. The X-ray tomography apparatuses used include the one performed at a synchrotron radiation facility, which has a spatial resolution level close to the theoretical limit of the projection-type imaging, in addition to two industrial apparatuses. It has been shown that even if industrial apparatuses, which inevitably possess limited spatial resolution levels, are used, the real size and fraction of microstructural features can be estimated by performing imaging experiments above a certain spatial resolution level. It would be, so far as the authors are aware, the first time to demonstrate the feasibility of laboratory-scale X-ray tomography imaging in microstructural observation in a systematic manner, especially focusing on spatial resolution and quantitative capability.
    抄録全体を表示
    PDF形式でダウンロード (2973K)
  • 粉末缶押出によるVGCF強化アルミニウム基複合材料の作製とその強化機構の検討
    小川 文男, 増田 千利
    原稿種別: 研究論文
    2013 年 63 巻 10 号 p. 350-357
    発行日: 2013/10/30
    公開日: 2013/11/30
    DOIhttps://doi.org/10.2464/jilm.63.350
    ジャーナル フリー
    抄録を表示する抄録を非表示にする
    Aluminum matrix composites reinforced by vapor grown carbon fibers (VGCF) were fabricated by powder can extrusion. Extrusion ratio was 9 or 16. Temperature and heating duration were changed to investigate the effect of extrusion condition on properties of composites. Measurement of micro-Vickers hardness, tensile strength was conducted and microstructure such as VGCF orientation was characterized. When extrusion temperature was higher or when heating duration was longer, mechanical strength was lower, but fracture strain was higher. In addition, reinforcing efficiency to aluminum was higher for longer heating duration and higher extrusion ratio, due to improved VGCF orientation. Strength was modeled considering load bearing by VGCF, VGCF orientation, work hardening of matrix due to thermal expansion mismatch of VGCF and aluminum and Orowan looping mechanism. From those results and the observation of aluminum grain in composites, reinforcing mechanism of VGCF reinforced composites was discussed.
    抄録全体を表示
    PDF形式でダウンロード (4530K)
解説：特集「アジアにおけるものづくり最前線」
連載講座
    • |<
    • <
    • 1
    • >
    • >|
feedback
 Top