溶接学会誌
Online ISSN : 1883-7204
Print ISSN : 0021-4787
ISSN-L : 0021-4787
21 巻, 3 号
選択された号の論文の6件中1~6を表示しています
  • 軟鋼接合に関する豫備実験
    大井 一郎
    1952 年21 巻3 号 p. 1-6
    発行日: 1952年
    公開日: 2011/01/26
    ジャーナル フリー
    This paper reports the results of a preliminary experiment on the gas pressure welding intended for application to the welding of rails or car parts.
    The writer used a 25mm ∅ mild steel rod, the cut surface of which was finished by lathe. The results were as follows:
    1) The max. temperature of the welded part was lower than 1200°C even with two No.10 blowpipe nozzles applied; i. e., below its melting point.
    2) Metallographically, the welded part was perfect with no decarburization, but within the area of about 30mm of the joint, grain growth was recognized.
    3) The writer considered many weldtng factors and established the operation standard. Whenever the operation Was carried out by this standard, the tensile strength, elongation, Charpy value and fatigue strength of the joint turned out invariably very excellent.
    From this experiment, he was convinced that this method would be well applicable to the intended purpose.
  • 浮田 勇, 橋本 達哉, 小林 忠
    1952 年21 巻3 号 p. 6-12
    発行日: 1952年
    公開日: 2011/01/26
    ジャーナル フリー
    In this experiment, the factors affecting consistency of shear strength have been investigated. It has been discovered that it is necessary in order to attain a high degree of consistency that welding conditions be kept under control.
    There must be certain optimum welding conditions for securing consistency, so to find such factors affecting consistency some experiments have been performed.
    The following conclusions were drawn:
    1) The shape of characteristic curve of consistency is “V”-type against the several welding conditions, the lowest depression representing the best condition.
    2) To obtain good consistency, surface preparation is important ; the chemical method is superior to wire-brushing.
    3) It appears that the shape of wave form of welding current affects consistency.
    4) Especially it is important for the best results that weldtng conditions be kept as constant as possible.
    5) The lighter the gage, the narrower becomes the ranw of good cosistency.
  • 渡辺 正紀, 合田 進
    1952 年21 巻3 号 p. 13-19
    発行日: 1952年
    公開日: 2011/06/07
    ジャーナル フリー
    代表的な本邦縁付鋼4種について静的曲げおよびシャルピー衝撃試驗を行つた. ただし試験片はU型標準シャルピー試片を採用した. 得られた結果を要約すれば次の通りである。
    (a) 種々なる温度における荷重-撓み曲線の特性を論議するにあたり, 次のcriterionを採用した.
    ∅=最大荷重/最大荷重点における撓み量
    ∅´= (最大荷重) - (降伏荷重) /最大荷重点における撓み量
    第9図に示すごとく, これらの値はそれぞれ無負荷状態から最大荷重点までの平均歪硬化率および降伏点から最大荷重点までの平均歪硬化率を示す.
    (b) ∅および∅´の値は我々の実験温度範囲 (-80℃~+100℃) では温度に無関係に一定を保つ.
    (c) 第16図および第17図に示すごとく, ∅,∅´の値の小さい材料程遷移温度は低い.
    (d) 材料のnotch toughnessを到定する場合, 遷移温度の低い材料に対してはシャルピー試験より静的曲げ試験の方がよく, 逆に遷移温度の高い材料ではシャルピー試験の方がよい.
    (b) および (c) から材料のnotch toughnessを判定するにあたつては, 室温における材料の∅,∅´の値をcriteriouとすればよいといへる.
  • 山口 太三郎, 高田 安之
    1952 年21 巻3 号 p. 19-21
    発行日: 1952年
    公開日: 2011/01/26
    ジャーナル フリー
    Arc currents flowing through some weldihg electrodes are measured with use of both an A. C. and a D. C. ammeter connected in series. Readings of the D. C. ammeter are remarkable in both iron and stainless steel electrodes having no flux, and are small, generally, in electrodes covered with fluxes.
    Maximum power of the welding will be secured with use of electrodes, arcs of which do not rectify.the currents.
  • 第1報補遺
    應和 俊雄
    1952 年21 巻3 号 p. 22-24
    発行日: 1952年
    公開日: 2011/01/26
    ジャーナル フリー
    In Report I the author obtained the values of activation energies for several electrodes made by Kobe Steel Works.
    In the investigation of this energy, the following points must be considered: 1) To study the relation between activation energy and metal constitution, welding conditions should be kept constant.
    2) The tempering method is only an approximation; the, isothermal method must be adopted for more exact values.
    3) The “;Rate Process Theory” can applicable only to the single process.
    4) Activation energy can be measured in terms not only of change in hardness but in other stresssensitive
    physical properties, e. g., electric conductivity, coercive force, etc.
  • 大西 巖, 菊田 米男
    1952 年21 巻3 号 p. 25-30
    発行日: 1952年
    公開日: 2011/01/26
    ジャーナル フリー
    It is reliable that the water content in electrode coating (i.e., free water, combined water and chemical water) has much influences upon the partial pressure of hydrogen in arc atmosphere during metallic arc welding.
    Van den Blink advocated the next formula as a quantitative relation between them;
    F=1-PH2·(PH2O) (1/PH2+1/PH2O+1/PCO+1/PCO2) (1)
    When F>1, partial pressure of hydrogen increases in accordance with increase of the water content, but when F<1, the former decreases in spite of increase of the latter.
    Our experiments on this problem are as follow:(1) We calculated F in (1) theoretically at various compositions of arc atmosphere using water gas reaction at 1400°C, 1530°C, 1600°C and 1700°C, and determined the diagram of F=0.
    (2) Electrodes experimentaly used were three kinds of cellulose types, three limestone types, three deoxide types and four kinds of cellulose-limestone types. They were mixed with same base mixing.
    (3) The free water and other types of water in electrode coatings were separatly measured at 110°C and 1100°C. Arc atmosphere generated from drying and non-drying (as wet) electrodes were collected and analized.
    (4) The principal conclusions obtained were as follow:(a) When cellulose type electrodes were used, the partial pressure of hydrogen was very little affected by drying or non-drying of the electrode coatings.
    (b) When other type electrodes, particularly limestone types, were used, the partial pressure of hydrogen from non-drying electrode showed remarkable increase than that from drying electrode.Therefore, electrodes, except cellulose types, must be dried sufficiently before they are used in welding.
feedback
Top