-
伊藤 英覚
1984 年 50 巻 458 号 p.
2267-2274
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
-
真田 徳雄, 高山 和喜, 小野寺 収, 池内 準
1984 年 50 巻 458 号 p.
2275-2284
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
ホログラフィ干渉計法と高速度撮影法を用いて,振動場における気泡の生成・崩壊と,それにともなって発生する衝撃波の様相を,十分な空間精度で観測した.その結果,振動の圧縮・膨張過程に対応する,気泡と衝撃波の挙動を定量的に明らかにした.また,試験面あらさと生成する衝撃波の関係,および試験圧力と衝撃波の関係を評価した.さらに衝撃波伝ぱ速度の測定から,試験面近傍での衝撃圧力は,1GPaをこえることを明らかにした.
抄録全体を表示
-
大場 利三郎, 伊藤 幸雄, 樋口 二郎, 野崎 智, 中村 義郎, 和田 宏三, 宮倉 秀人
1984 年 50 巻 458 号 p.
2285-2292
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
ジェットフロー形仕切弁に生ずるキャビテーションの発生機構と諸障害の解明を目途とし,1/10縮尺模型まわりのキヤビテーションの様相とその衝撃音圧を種々の弁開度において同時観察し,「タイプ,発生域,消滅点および衝撃波形の異なる3種のキャビテーションの存在」,「小開度での高壊食性のせん断層形キャビテーションの卓越と噴流の偏向による壊食の危険性の増大」,「壊食と騒音との間には必ずしも正の相関はない」などを明らかにした.
抄録全体を表示
-
松下 通紀, 赤松 映明
1984 年 50 巻 458 号 p.
2293-2298
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
前報で提案したはく離を伴う非定常層流境界層の1パラメータ積分法による数値解法において,はく離流の速度分布に後方よどみ点流れの数値解を利用し,流束ベクトル分割法によって数値計算の安定化を計るなどの改良を行った.さらに非定常境界層のはく離特異性を特性曲線の包絡による不連続の生成としてとらえ,円柱の出発流における特異性の発生を調べたところShenらの厳密な解析と一致する結果を得た.
抄録全体を表示
-
大坂 英雄, 中村 育雄, 影山 芳郎
1984 年 50 巻 458 号 p.
2299-2306
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
d形粗面上の乱流境界層の平均量特性が実験的に調べられた.特に,壁面摩擦応力が直接測定により求められ,本実験範囲において摩擦抵抗係数は一定値をとることが分かった.この値を基礎として,原点補正量,平均速度分布および境界層特性の下流方向への発達が評価された.さらに,運動方程式と平均流および乱流運動エネルギ式の収支から,滑面およびk形粗面上の流れと本流れとの特性の差異が明らかにされた.
抄録全体を表示
-
若 良二, 吉野 章男, 林 農
1984 年 50 巻 458 号 p.
2307-2315
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
接線方向吹出しを持つ円柱のおもに側壁付近において,円柱の諸特性値の翼幅方向分布に関する実験を行った.主要なパラメータはスロット位置と円柱が側壁を貫通する部分(側壁部)のスロット構造である.スロット位置,スロット構造により側壁付近の諸特性値の分布は著しく変化し,側壁の影響がおよぶ範囲も変化する.スロット構造を"エッジ形"とした場合,スロット位置が下流側にあるほど側壁の影響がおよぶ範囲は狭くなる.
抄録全体を表示
-
佐野 勝志
1984 年 50 巻 458 号 p.
2316-2324
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
両吸込うず巻ポンプ〔比速度266(m
3/min,m,rpm)〕の吸込管の上流,および吐出し管の下流にタンクを接続した系について,羽根通過周波数と液柱の固有振動数が一致して共振したときの変動圧力の振幅におよぼす,定在波とポンプとの相対位置の影響を調べた.その結果,ポンプの脈動発生源の相当位置が,変動圧力の節と一致すると共振時の変動圧力の振幅は最大となり,腹と一致すると最小になることなどを明らかにした.
抄録全体を表示
-
田中 裕久
1984 年 50 巻 458 号 p.
2325-2333
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
海洋の波力エネルギを吸収する方法に浮体を利用する方式がある.浮体に非対称形状浮体を用いると1自由度の運動でも効率よく吸収することがわかっている.ここでは,新しい形状の上下運動の浮体を提案しkochin関数法による理論解析と水槽試験による基本性能の確認を行い,これをもとに排水量1トンの浮体を作製して東京湾内で海上試験を行い,不規則波中の波力吸収のあり方を動力変換工学的に論じた.
抄録全体を表示
-
松永 成徳, 宇野 美津夫, 塚本 寛
1984 年 50 巻 458 号 p.
2334-2342
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
三次元非定常流計測用5孔ピトープローブの測定精度を明らかにするために理論的研究が行われた.プローブ・ヘッドの非定常圧力分布,圧力測定系の動特性を考慮した理論計算が行われ,測定精度がストローハル数の関数として示された.さらに,その結果を利用して,所要の非定常流計測に最適なプローブ設計法が示されている.
抄録全体を表示
-
世古口 言彦, 田中 収, 上野 隆司
1984 年 50 巻 458 号 p.
2343-2351
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
ポーラス管による液膜抽出でエントレインメント流量を測定する方法の問題点を明確にすると共に,じょう乱波および基底液膜の抽出過程と,じょう乱波間の液滴濃度とを考慮した解析モデルを設定し,エントレインメント流量の決定に対する基本的関係を提示する.さらに,ポーラス管の正味の液膜抽出長さを微細に変化させうる装置を製作し,抽出長さと液膜抽出量の間の詳細なデータを得,解析モデルによる予測の妥当性を確認した.
抄録全体を表示
-
富田 侑嗣, 林 照彦
1984 年 50 巻 458 号 p.
2352-2360
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
粉粒体の空気輸送における混入器の一種である,輸送管がタンク上部から出ているブロータンク輸送機について,その供給量の被輸送物の種類,輸送管入口ノズル,多孔板形状および輸送管径との関係を実幹的,理論的に調べ,粒体では輸送管入口形状によって,粉体では多孔板形状によって大きな影響を受けることを明らかにした.
抄録全体を表示
-
富田 侑嗣, 船津 勝也, 東 和彦, 白倉 典幸, 山本 雅英
1984 年 50 巻 458 号 p.
2361-2367
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
粉体の垂直上昇管における高濃度空気輸送について気流の圧縮性を考慮し等温流れとしたときの,輸送管に沿う圧力,速度,粒子濃度の変化を数値解析し,その結果を主として圧力分布の測定値によって検討した.数値計算で圧力変化などに現実的な解を与える条件を置くことにより,それぞれの計算条件について粒子の初期体積分率とその摩擦係数に関してそれらのとりうる値は一定の範囲内に限定されることが示された.
抄録全体を表示
-
高松 康生, 古川 明徳, 大熊 九州男, 下釜 康彦
1984 年 50 巻 458 号 p.
2368-2377
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
極低落差の水力利用を目的としダリウス形横流水車を試作試験した.ランナ効率は開放ランナが良いが密閉流路ランナのほうが水車効率が高く,二枚翼は四枚翼より高効率で流体性能的には十分実用性がある.また1回転中のトルク変動の実測結果と理論的考察によれば,翼性能推定には回転翼効果への配慮が必要で,これは等価なそりと迎え角の変化として計算できるが,これに加えて流れの非定常効果を含めた翼特性のは握が必要である.
抄録全体を表示
-
辻 裕, 森川 敬信, 蝶野 成臣, 井前 弘幸, 吉川 敏和
1984 年 50 巻 458 号 p.
2378-2385
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
まず,受圧板の直径がカプセル本体の直径よりも大きい実用カプセルに対応する流体抵抗式を導いた.つづいて,加速区間におけるカプセルの走行を,送風機の性能曲線およびバイパスからの空気流出を考慮し,運動方程式に基づいて解析した.さらに,終端を閉鎖した管路にカプセルを突入させ,空気の圧縮性を利用して停止させる場合についても運動を計算した.以上の結果,計算値が実験値に満足に一致することが確認された.
抄録全体を表示
-
蝶野 成臣, 辻 裕, 井前 弘幸, 吉川 敏和, 森川 敬信
1984 年 50 巻 458 号 p.
2386-2392
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
複数カプセルの走行の取扱いの基礎として,2個のカプセルの走行特性を実験的に調べた.その結果,2個のカプセルの発進時間間隔が,システム全体に比較的大きな影響をおよぼすことが明らかにされた.またこの影響は,直径比が大きいはど著しい.つづいて,単一カプセルに対して用いた理論を2個のカプセルの場合に応用して解析を行った結果,計算値と実験値に満足な一致が得られることがわかった.
抄録全体を表示
-
斎藤 彬夫, 宇高 義郎, 秋吉 正寛, 片山 功蔵
1984 年 50 巻 458 号 p.
2393-2400
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
潜熱蓄熱カプセルの蓄熱時に現れる重要な伝熱機構の一つである,固相が伝熱壁面上へ押し付けられながら溶融し熱交換を行う系に関する熱伝達特性を明らかにするため,広範囲な測定を行うとともに,基礎式の無次元化により現象の支配パラメータを抽出した.この結果,伝熱量を決める無次元熱流束はステファン数と無次元接触面圧だけの関数となり,これらの関係が簡単な式で表せることを示した.
抄録全体を表示
-
日野 竜太郎, 植田 辰洋
1984 年 50 巻 458 号 p.
2401-2408
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
内管一様加熱の垂直環状流路を上昇するR113サブクール液が加熱され,表面沸騰を開始し,気ほう離脱,発達した核沸騰域と移行し,限界熱流束に至る過程について,壁温分布を測定し,気ほう発生状況の写真撮影を行った.沸騰開始点過熱度は質量速度と液サブクールにほとんど影響されないこと,写真観察から決定した正味蒸気発生点はSahaらの整理式とよく一致すること,を示した.
抄録全体を表示
-
趙 〓〓, 泉 正明, 島田 了八, 熊谷 哲, 武山 斌郎
1984 年 50 巻 458 号 p.
2409-2417
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
フィン列を有する管あるいはその管群を沸騰熱伝達に応用する場合の最適設計と利用限界を考察するため,最も単純な形状の縦形および環状フィンを対象に理論解析をおこなった.その結果,熱流束はフィンの高さが高くなるほど,厚さが薄くなるほど増加し,管群からの熱流束密度はフィンの厚さが薄いほど大きくなるが高さには最適値があり,2.5mm付近で最大となる.
抄録全体を表示
-
宇高 義郎, 斎藤 彬夫, 谷 達也, 渋谷 広彦, 片山 功蔵
1984 年 50 巻 458 号 p.
2418-2426
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
PTFE被覆面をはつ液面としてプロピレングリコール蒸気の滴状凝縮を実現させ,広い範囲の過冷度にわたる滴状凝縮曲線の観測を行った.曲線に大きな影響をおよぼすと考えられる離脱液滴径と蒸気圧力をそれぞれ二通りに定め,これらのパラメトリックな影響を示した.得られた曲線の形は水蒸気のものと類似しているが,熱流束の値は全般にわたって小さく、また,滴から膜への遷移の様相が異なっていることなどを明らかにした.
抄録全体を表示
-
綾 威雄, 成合 英樹
1984 年 50 巻 458 号 p.
2427-2435
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
蒸気がベント管を通してサブクール水中で凝縮する際発生する振動現象の内,低蒸気流量率時に特徴的なチャギング現象における流体振動の振幅と周期の解析を行い,一種の強制振動項となる供給蒸気による蒸気-水界面の押し下げ効果がチャギング特性を決定づけることを示した.解析結果から,蒸気流量率の増加とともに振幅・周期が減少し,ついにはチャギング発生がなくなるという凝縮振動への遷移を定量的に説明することができた.
抄録全体を表示
-
大村 悦二, 難波 義治, 牧之内 三郎, 関本 芳宏
1984 年 50 巻 458 号 p.
2436-2445
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
コーティング膜と金属材からなる二層円板に強度分布が軸対称なレーザビームを照射したとき,コーティング膜内部で熱吸収される場合の温度分布の理論式を積分変換法を用いて導いた.そして,モデル実験と具体的な数値計算を行って,コーティング材の熱物性値,吸収係数μ,膜厚dが円板の温度上昇におよぼす影響を考察した.その結果,コーティング膜厚に最適値の存在すること,その範囲はほぼμd=1~5であることなどがわかった.
抄録全体を表示
-
熊田 俊明, 広田 達也, 田村 伸彦, 石黒 亮二
1984 年 50 巻 458 号 p.
2446-2453
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
熱工学上重要な蒸発を伴う場合の対流熱伝達が,固体伝熱面のそれに比べて異常に増加するとする実験が多数報告されている.本研究は既存の実験によるN
u数に基づいて,対流以外の熱流入の影響を受けないS
h数を求めることにより,異常増加の主要な原因が対流以外の熱流入によることを確かめた.また,対流以外の熱流入補正法を考察し,N
u数の補正をしたところ,この場合にも異常増加がないことが明らかとなった.
抄録全体を表示
-
熊田 俊明, 田村 伸彦, 広田 達也, 石黒 亮二
1984 年 50 巻 458 号 p.
2454-2460
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
乱流気相と水面間の熱と物質伝達に関する実験的研究.第1報で提案した対流以外の熱流入補正法を適用して補正することにより,熱伝達率は固体平板のそれに一致することが確かめられた.また,温度分布から計算した対流以外の熱流入と補正法による熱流入が一致することより補正法の妥当性が確かめられた.実験結果は液面容器への熱流入を防ぎ,水面温度が不均一のため水面温度を正確に決定することが難しいことを示している.
抄録全体を表示
-
池上 詢, 塩路 昌宏, 大澤 孝明, 王 世均
1984 年 50 巻 458 号 p.
2461-2468
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
エチレンおよびアセチレン噴流拡散炎内の流動を光電子相関レーザドップラ流速測定法で調べるとともに,散乱光強度変動自己相関からスート粒子群の空間分布を推定して,混合状態を調べた.その結果,熱解放によって強められた乱れが大きな渦構造をもたらし,そのために周囲の空気が内部まで浸透することが示唆された.また,燃料の差異によって空気飲込み渦の大きさが変わることが示された.
抄録全体を表示
-
新井 雅隆, / 廣安 博之, Hiroyuki HIROYASU
1984 年 50 巻 458 号 p.
2469-2477
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
旋回流燃焼器内で,同一の噴霧推力と平均粒径を持つガソリン,燈油,重油の噴霧燃焼を行わせ,温度分布やTHC,NO
x,すすの各濃度変化を調べた.その結果,スワールのない流れの場合には燃料による温度分布の差が顕著なこと,重油燃焼時に排出されるNO
xは低スワールの場合に特に多いこと,すすの排出濃度は燈油の場合に一番すくなくガソリン重油の順に増加しかつスワール数とともに増加することなどが明らかになった.
抄録全体を表示
-
吉川 典彦, 篠原 秀俊, 松井 英憲
1984 年 50 巻 458 号 p.
2478-2486
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
水素,メタン,エチレン,エタン燃料の酸素または空気との大気圧・常温混合気について,爆ごう波の構造の数値解析を行い,燃料濃度が発熱・反応誘導過程におよぼす影響を明らかにした.発熱速度を比較すると,水素>エチレン,エタン>メタンの順位となった.特性発熱時間の逆数に対応するパラメータを考え,これと爆ごう限界との関連を調べた結果,燃料の種類によらず限界濃度付近でほぼ10
6S
-1のオーダにあることがわかった.
抄録全体を表示
-
古浜 庄一, 小林 良行
1984 年 50 巻 458 号 p.
2487-2495
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
水素燃料噴射2サイクル火花点火エンジンのいっそうの性能向上のためには過給化を含めてその掃気状態の特性を明らかにする必要がある.水素噴射では燃焼ガス組成が簡単でガス分析による解析が容易であるのでそれを利用し,燃焼室より点火前のガスをサンプリングして掃気効率,給気効率を求めた.さらに機械およびターボ過給の効果を検討し,それによれば,0.2~0.3気圧の過給は実用的に有効であることがわかった.
抄録全体を表示
-
岸浪 絋機, 斉藤 図
1984 年 50 巻 458 号 p.
2496-2499
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
本研究は凸面加熱半円筒と凹面非加熱半円筒の組合せを1段とした5段の垂直波状板からの空気の自然対流熱伝達の実験を半円筒部Dと加熱部壁温θ
wを変えて行い,非加熱部の壁面放射を無視して壁内熱伝導を極く小さくした条件のもとで各段非加熱部の壁温分布,各壁面上の温度境界層と流れ場の挙動,さらに各段加熱部の局所ヌセルト数,各段平均と全段平均ヌセルト数の傾向などを調べ,このような場の熱伝達の特徴を明らかにした.
抄録全体を表示
-
関 信弘, 福迫 尚一郎, 米田 昌司
1984 年 50 巻 458 号 p.
2500-2504
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
凹凸両面が等熱流束加熱された二平行曲り板返しベンドに速度境界層が十分に発達した水流が流入する際の平均流速,平行板間隔,ベンド曲率半径およびプラントル数などの諸因子が返しベンド平均熱伝達に与える影響を明らかにし,その整理式の提案を行った.その結果凸面の平均熱伝達率はベンド曲率半径のほぼ0.09乗に比例するのに対し凹面の場合にはほぼ-0.21乗に比例し対照的な傾向を示すなどということが明らかとなった.
抄録全体を表示
-
野中 士郎, 笹田 哲男
1984 年 50 巻 458 号 p.
2505-2509
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
In order to develop high-efficiency turbine blade profiles, various kinds of time marching methods have been proposed for computing mixed subsonic-supersonic flows with shock waves. However, while two dimensional analyzers are now widely used for the computation of the flows, three dimensional analyzers suffer from consuming long CPU time because of the large amount of calculation. This paper presents a new method of reducing this drawback. In this method, the time dependent Euler equations are solved by time marching and volume approach. In order to save CPU time, two step solution (using fine mesh and coarse mesh) is introduced and the programs are coded to utilize APs (array processor). Consequently, a great saving of CPU time and accurate calculation can be obtained.
抄録全体を表示
-
岡田 修, 高浜 平七郎, 藤田 秀臣
1984 年 50 巻 458 号 p.
2510-2517
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
An air-water annular mist flow has been studied experimentally using a long horizontal pipe of about 30 mm diameter and 24.5m long, for two extreme cases of the air-water mixing devices, a porous wall and a nozzle installed along the pipe axis. It was observed that the flow patterns and the onset of the large disturbance wave were remarkably influenced by the mixing device. In the case of nozzle mixing, the total flow rate of dispersed water G
le did not axially decrease and became a minimum and then turned to increase monotonously, attaining a certain constant value, whereas in the porous wall mixing it increased monotonously and attained a constant value. The non-equilibrium length (x/d)
φ decided by the axial change of G
le was not so remarkably different between both mixing devices. The value of (x/d)
φ was at least 400 in the range of the air velocity u
go≥52.1m/s and the liquid Reynolds number R
elo≥484.
抄録全体を表示
-
正司 秀信, 大橋 秀雄
1984 年 50 巻 458 号 p.
2518-2522
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
Fluid forces on a rotating centrifugal impeller in whirling motion were calculated by using unsteady potential theory. Two types of impeller surrounded by vaneless diffuser were considered and calculations were performed for various values of whirl speed and flow coefficient. The effects of flow coefficient to the fluid forces were shown and the results showed that they exert a damping effect on the rotor in almost all cases. The impeller surrounded by guide-vanes were also considered. The effects of the vane angle and the clearance were clarified and it was shown that the average value of fluid forces over a few period changes for small values of clearance.
抄録全体を表示
-
原 秀介, 鈴木 俊紀
1984 年 50 巻 458 号 p.
2523-2526
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
The hydrodynamic forces generated by the water-disk interaction have been investigated experimentally. Two kinds of disk models of 100 mm and 150 mm diameter were used. The disk was oscillated horizontally in standing water by a mechanical oscillation machinery. The force was measured by means of quartz force transducer. Period parameters ranging from 0.1 to 0.6 and Reynolds numbers from 880 to 71000 were covered in the investigation. The results have shown that the wave forms and the amplitudes of the forces are found to depend on a period parameter.
抄録全体を表示
-
森谷 優, 坂本 弘志
1984 年 50 巻 458 号 p.
2527-2530
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
The effect of the forced oscillation of the upstream cylinder on the fluctuating forces of the downstream cylinder in small staggered arrangement was studied experimentaly. The fluctuating forces acting on the downstream cylinder were measured by the load cells. When the spacing between two cylinders is smaller the flow around two cylinders is influenced by the oscillation of the upstream cylinder. In particular, the oscillation of the upstream cylinder produces two distinct lock-in regions on the fluctuating forces of the downstream cylinder.
抄録全体を表示
-
岡島 厚, 杉谷 賢一郎
1984 年 50 巻 458 号 p.
2531-2538
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
Pressure distribution, drag coefficient and Strouhal number of tandem circular cylinders were measured in a wind tunnel. Furthermore, we simulated flow beyond the critical Reynolds number, using surface roughness. Flow-characteristics around a downstream cylinder immersed in a wake of an identical cylinder were investigated in detail. We found that at subcritical Reynolds numbers, a wake behind the downstream cylinder consists of two kinds of predominant componets with different frequencies, i. e. one component due to a vortex-street shed from an upstream cylinder (Strouhal number, S
t=0.2) and the other due to a vortex formed just behind the downstream cylider (s
t=0.12-0.18). At high subcritical Reynolds numbers, a reduction in the drag force on the downstream cylinder becomes more apparent with an increase of Reynolds number and is clearly due to the influences of turbulence in the wake, which results in a strong dependence of the drag force upon Reynolds number. It was found, in addition, that the Strouhal number of the downstream cylinder changes from 0.18 to 0.3 with an increase of Reynolds number, although the Strouhal number of the upstream cylinder is 0.2. In the transcritical region simulated with the aid of surface roughness, the drag force on the cylinder in a wake is no longer dependent upon Reynolds number.
抄録全体を表示
-
坂本 弘志, 森谷 優, 小畑 芳弘
1984 年 50 巻 458 号 p.
2539-2544
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
In the foregoing paper, the characteristics of the time-mean aerodynamic forces caused by two circular cylinders of finite heigth placed vertically in a turbulent boundary layer were described. As continuation of the foregoing paper, the behaviour of the fluctuating aerodynamic forces of one circular cylinder was investigated under interference effects from the other cylinder with similar size. Experimental data were collected to examine the effect on the fluctuating aerodynamic force due to the variation of the distance between two circular cylinders and the angle of attack of approaching flow. The results are summarized in several figures from which one can obtain the fluctuating drag, the fluctuating lift and the Strouhal number based upon the prevailing frequency of the fluctuating lift for all arrangements within distances between two circular cylinders less than six times diameters.
抄録全体を表示
-
前田 昌信, 菱田 公一, 小野 通隆
1984 年 50 巻 458 号 p.
2545-2548
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
The grading up of LDV performance inevitably follows the increase of weight of the equipment and it requires fine techniques setting up optic devices due to its complexity of the structure. For measuring the flow pattern an large travercer will be also used. However, the use of fibre optics makes the light optic probe. The probe will be easily employed in any attitude. This paper deals with the developments of the fibre LDV with double Bragg cells to measure backward flows and shows the results measured in the boundary layer on a heating plate in an inclined flow to the gravitational direction.
抄録全体を表示
-
佐々木 久郎, 木谷 勝
1984 年 50 巻 458 号 p.
2549-2554
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
Longitudinal velocity fluctuations in the reverse-flow of a separation bubble formed at the leading edge of a blunt flat plate are found to be approximated by a Gaussian distribution. The reverse-flow intermittency I
r is thus represented by the error function of the time-mean value of the local longitudinal velocity divided by its r.m.s. value: the distribution of I
r near the plate is also expressed by the same function of the longitudinal distance relative to the time-mean reattachment point. The frequency of switching of flow directions is uniquely related to I
r. A high heat-transfer rate in the reattaching zone is suggested to be caused by a more frequent renewal of viscous sublayers there than in a more downstream region.
抄録全体を表示
-
土方 邦夫, 森 康夫, 石黒 博
1984 年 50 巻 458 号 p.
2555-2562
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
Turbulent flow structure and heat transfer in a pipe with arc shaped cascade turbulence surface promoters are experimentally studied for applying to the thermoelectric ocean thermal energy conversion (OTEC). Mean velocities and turbulence properties such as turbulence energy and Reynolds shear stress are measured by the one color laser Doppler velocimeter with Bragg cell. To exactly measure the whole flow field, especially the one around the promoter, a glass tube with a smooth rib and water solution of sodium iodide having the same refrative index as the pipe material are used as the test section and the working fluid, respectively, to prevent the refraction of the laser beam at the interface between them. Relations among turbulence energy, Reynolds shear stress, pressure loss and local heat transfer conefficient are discussed on the basis of the experimental results for the different rib heights.
抄録全体を表示
-
木谷 勝, 松村 昌典
1984 年 50 巻 458 号 p.
2563-2570
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
Turbulence structure in the intermediate wake of a normal flat plate was studied experimentally by a conditional-sampling technique. The measurements were made at a section 8.0 heights downstream of the front face of the plate. Velocity fluctuations were decomposed into those produced by large-scale structures and those associated with small-scale structures: the former fluctuations were again decomposed into the phase-averaged fundamental component and the deviation from it (large-scale deviation). Velocity vector fields, contours of streamlines, vorticity of the fundamental components, together with contours of intensity and correlation of the large-scale deviation velocity, were presented and discussed. Contours of intensity, correlation and turbulence intermittency of the small-scale fluctuations were also presented in and around the large-scale structures. Large Reynolds shear stress associated with the large-scale deviation velocity was suggested to be a result of the stretching of vortex filaments in the saddle-point flow region.
抄録全体を表示
-
大坂 英雄, 影山 芳郎, 小山 さとる
1984 年 50 巻 458 号 p.
2571-2578
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
The turbulent structure of the turbulent boundary layer over a d-type rough surface was examined using both x type-hot wire and usual time averaged procedure, and hot-wire rakes and conditional sampling techniques. Results showed that even in the present rough boundary layer the almost same organized structure as found in the smooth surface boundary layer existed, and that this structure was at an oblique angle of about 23 deg. To the free stream and also indicated a high degree coherence over a considerable area in the direction normal to the wall. Conditional averaged results showed that the strong accelerations of the streamwise velocity occurred at y
+=15 to y/δ=0.7. It could be deduced from this pattern that there existed the events associated with the bursting phenomenon.
抄録全体を表示
-
石垣 博
1984 年 50 巻 458 号 p.
2579-2585
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
The round turbulent buoyant jet issuing vertically into quiescent fluid is studied analytically. Formulae on maximum velocity, temperature, concentration and entrainment rate are derived. These formulae agree well with the available experimental data for whole region of jet and plume. Quantitative classification as to the flow regime of jet, transition and plume are given for the nondimensional distance from jet exit.
抄録全体を表示
-
藤田 重隆, 大坂 英雄, 上野 五郎
1984 年 50 巻 458 号 p.
2586-2591
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
Mean flow properties of air jet issuing from the cruciform nozzle with a sufficiently large value of aspect ratio into still air have been observed in a wide region of the flow field. From this experiment, it is clarified that the streamwise variation of the both scales of velocity and length is slower than that of the two-dimensional and axisymmetric jets. The velocity contours show a symmetric, crisscross shape even at the most downstream section measured in this experiments, whilst in the upstream region the velocity profile exhibits the saddle-back shape for both symmetric slice of y=0 and z=0. In the region of x/d≥75 the velocity profiles can be expected to be geometrically similar in the entire flow field.
抄録全体を表示
-
石井 好, 東野 文男, 桜井 明
1984 年 50 巻 458 号 p.
2592-2595
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
Nitrogen or hydrogen gas is set to spurt from a small circular hole located at the endplate of shock tube at about 0∼9 ms before the shock wave arrives and reflects there. Interacting with the jet the reflected shock wave changes its shape from a plane shock wave to a curved one. We observed the phenomenon by the use of a schlieren system, time counters and pressure gauges. The results of the observation are as follows : (1) It is confirmed that an unstable, curved, reflected shock wave turns back to a stable plane shock wave within 0.1 ms. (2) The pressure and the temperature values behind the reflected shock wave derived from its distance-time relation show a certain amount of jump, which indicates the amount of the interaction between the spurting gas and the shock wave. (3) It is seen that hydrogen jet starts to burn at about 500∼600μ s after the shock reflection is taken place.
抄録全体を表示
-
畑中 貞男, 角南 孝一, 平井 三友
1984 年 50 巻 458 号 p.
2596-2601
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
A numerical analysis of molten thermoplastics flow in straight flow channel with circular cross section, involving solidification of the melt on the mold wall, is presented here. Thermal properties such as density, thermal conductivity and specific heat are considered temperature dependent, and thermal conduction in the mold is also considered in this analysis. Numerical results of temperature, velocity and pressure distributions, obtained from the analysis which is applied to low density polyethylene flow under various initial and boundary conditions, are useful in more complete understanding of molten thermoplastics flow during the filling stage in the injection molding and reasonable design of flow channels such as sprues, runners.
抄録全体を表示
-
澤 洋一郎, 森井, 松平 秀雄
1984 年 50 巻 458 号 p.
2602-2607
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
Air pressure pulses occurred in drainage pipes induce oscillating motions of water in drain traps accompanied with the outflow of a part of the water. This paper deals with the behavior of the water as the transient response of oscillation system. In this system, mass of the water decreases momentarily. A mathematical model for the system is introduced. With making impulse response model experiments and the simulations, the system parameters of the mathematical model are indentified. This method is one of the system identification methods in modern automatic control theory.
抄録全体を表示
-
平松 力, 古村 義彰, 伊藤 敦
1984 年 50 巻 458 号 p.
2608-2613
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
The perpose of this analysis is to predict the vibration level of a pipe conveying a two-phase flowing fluid. Experiments were carried out with a perpendiculary supported U-type piping system, conveying an air-water two-phase flow in a steady state condition. Fluctuation signals are observed by a void signal sensor, and power spectral densities and probability density functions are obtained from the void signals. Theoretical studies using FEM and an estimation of the exciting forces from the PSD of void signals, provided a good predictional estimation of vibration responses of the piping system.
抄録全体を表示
-
朝倉 俊行, 段野 勝, 川端 洋平, 藤中 雄三, 林 庄司
1984 年 50 巻 458 号 p.
2614-2618
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
The purpose of the research is to develop the measuring device for the ventilation in tunnels. This device measures the differences of pressures between two points, using two devices of the same construction, by which the headloss of tunnels may be calculated. This device is composed of a container in which the air pressure is kept constant as the reference pressure, and is equipped with a manometer to detect the difference between the reference pressure and the ambient air pressure. In order to obtain the reference pressure, it is necessary for the container of the device to be kept at a constant temperature with the accuracy of 10
-3°C. Firstly, both the structure and its operation of the device with double-walled container is explained. Secondly, the dynamics of temperature may be represented as a on-off feedback control system and its characteristics of temperature is analyzed in detail. Finally, the experimental studies are performed and the good regulation response may be obtained at the high accuracy within 10
-3°C.
抄録全体を表示
-
田原 晴男, 真鍋 明
1984 年 50 巻 458 号 p.
2619-2624
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
When inducer is attached to centrifugal pump in order to improve the suction performance of the pump, the inducer is required to have better suction performance and enough total head. Then cambered inducer which is expected to satisfy these requirements is suggested because its inlet and outlet angles can be selected independently. In this paper, experimental studies of several cambered inducers that were made on same design conditions except inlet and outlet angles were performed and followings were clarified. First, the outlet angle had effects on the exit flow condition and the total head of inducer. Second, the suction performance of the pump equipped with inducer was determined by inlet angle but influenced by the suction performance of pump when the total head of inducer was not enough.
抄録全体を表示
-
加藤 榮二, 吹田 年, 川又 正昭, 大森 伸一
1984 年 50 巻 458 号 p.
2625-2630
発行日: 1984/10/25
公開日: 2008/03/28
ジャーナル
フリー
Studies have been made to compare and discuss the analytical solutions solved by the method of characteristics with the experimental results on the waterhammer. The measurements have been carried out using the 1/6 scale model of the primary coolant system of the experimental fast breeder reactor "JOYO" belonging to the Power Reactor and Nuclear Fuel Development Corporation. The waterhammer has been taken place at the valve throat area ratio ranging from 1/4 to 4/4 by varying in circulating pump revolving speed in the angular acceleration ranges 20 to 180 rad/s
2 and -20 to -180 rad/s
2. Good agreement was found between the analytical results and experimental. Therefore the calculation models and idea used in this paper have sufficient practical value.
抄録全体を表示