-
木内 学
1985 年 51 巻 469 号 p.
2197-2203
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
-
田中 信雄, 菊島 義弘
1985 年 51 巻 469 号 p.
2204-2212
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
本論文は,弾性支持法の高域遮断特性,サーボダンパ法の共振ピーク抑制特性および能動制振法の加振力抑制機能をすべて含む新しい制振法,すなわちハイブリッド制振法を提案し,振動公害の元凶となる加振力を幅広い領域にわたり抑制することを目的としている.まず,当制振法の基本原理を提示し,つぎに当制振系設計法を明らかにする.また,理論解析によりハイブリッド制振機能を明らかにするとともに,実験により本機能の検証を行う.
抄録全体を表示
-
今市 憲作, 福嶋 雅文, 石井 徳章, 村松 繁, 松永 寛
1985 年 51 巻 469 号 p.
2213-2223
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
本研究では,ローリングピストン形回転圧縮機の電源遮断後の振動,クランク軸の回転挙動およびシリンダ内の圧力に関する計測データを示す.その結果,圧縮機の電源遮断後の動的挙動を決定する主要因が電源遮断時のクランク回転角であり,それをある範囲内に電気的に制御することによって,振動および騒音の発生を常に最小限に保って,定常運転中の圧縮機を停止させることが可能であること,を明らかにする.
抄録全体を表示
-
長屋 幸助, 武田 定彦, 林下 豊彦
1985 年 51 巻 469 号 p.
2224-2232
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
任意動トルクを受ける任意形状断面棒の衝撃ねじり応力の解析を行った.解析では,任意時間関数荷重はフーリエ展開法とラプラス変換法を適用して処理し,さらに境界条件はフーリエ展開境界値平均法により満足させた.得られた理論結果は数値計算の過程でデータのみを与えることで,あらゆる動的トルクを受けるあらゆる断面形状の棒に適用できる一般式である.また数値計算を行い種々の断面形状を有する棒の衝撃ねじり応答を解明した.
抄録全体を表示
-
小野 京右
1985 年 51 巻 469 号 p.
2233-2243
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
一自由度振動計にモデル化できる振動機構形をその固有周期近傍の時間で一定速度に起動させる場合,残留振動が生じずしかも最小の消費エネルギで駆動できる最適な駆動関数を導く手法を提案し,その多項式近似解を求めた.最適な駆動関数による消費エネルギは剛体駆動における最小消費エネルギにほぼ等しくなり,また振動機構形のパラメータ変動による残留振動の発生感度を小さくすることができる.
抄録全体を表示
-
荻原 憲明, 河野 敬
1985 年 51 巻 469 号 p.
2244-2252
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
簡易モデルによる解析結果から,回転体の接触不安定振動に関し,内周接触では前向きふれまわり,外周接触では後向きふれまわりが不安定モードとなることがわかった.また各単独の接触形態ならびに内・外周同時接触形態での安定限界速度や限界摩擦係数を解析的に予測し,安定域を広げるための指針が得られた.軸受減衰効果やジャイロ効果の検証も行い,不安定振動に及ぼす影響度が高いことがわかった.
抄録全体を表示
-
石田 幸男, 山本 敏男, 池田 隆, 秋田 哲義
1985 年 51 巻 469 号 p.
2253-2260
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
非線形ばね特性を持つ対象回転軸において,前向き歳差運動様式の1/2次分数調波振動とばね剛性の方向差に起因する後向き歳差運動様式の同期ふれまわり振動の共進展がほぼ一致する場合の内部共振現象について,極座標表示非線形成分との関連に注意し,その特性を理論的,実験的に調べた.その結果,これら二つの振動は連成して複雑な共振曲線となり,また分数調波振動が二度発生するなど特徴ある現象が明らかとなった.
抄録全体を表示
-
斉藤 俊, 塚原 幸茂, 遠藤 満
1985 年 51 巻 469 号 p.
2261-2268
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
回転円筒の振動に関し,トルク,外圧,軸圧縮力のような初期応力が作用する場合について振動数解析を行った.その結果非回転時に初期応力が作用した場合には初期応力の種類,大きさにより固有振動数は低下するにもかかわらず,初期応力が作用し回転している場合でも動的な不安定現象は存在せず回転速度と回転時の固有振動数を非回転時の固有振動数で正規化した関数は円環の関係にほぼ一致することが明らかとなった.
抄録全体を表示
-
岩田 佳雄, 田村 章義, 佐藤 秀紀
1985 年 51 巻 469 号 p.
2269-2275
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
弾性支持されたたて形ロータでは,軸受支持の弾性主軸方向がすべての軸受で一致しない場合がある.本報では多軸受多円板の弾性ロータ系の各軸受に弾性主軸方向を考慮し,その解析に伝達マトリックス法を適用した.そして2円板ロータの危険速度とふれまわりについて実験と解析を行い,両結果を比較した.最後に簡単な弾性ロータモデルについて,その弾性主軸の方向が危険速度に及ぼす影響の定性的な特徴を明らかにした.
抄録全体を表示
-
岡田 養二, / 王 波平, BoPing WANG
1985 年 51 巻 469 号 p.
2276-2282
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
伝達マトリックス法は,特に直線状の構造物解析には,きわめて有効な構造解析法である.しかし伝達マトリックスの数値計算で,解が不安定になったり誤差が増加してしまうことがある.本論文では有限要素法などで使われるフロンタル解法を応用し,部分マトリックスの逐次リダクションによって計算の安定化と効率化をはかる方法を提案する.この計算方法は部分構造の特性変化を評価するリアナリシスへも,効率よく適用可能である.
抄録全体を表示
-
和田 稲苗, 西田 俊一
1985 年 51 巻 469 号 p.
2283-2290
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
非ニュートン流体に対する修正ダルシの法則を適用して,多孔質スクイズ軸受の弾性流体潤滑の挙動を明らかにすることにより,生体関節の潤滑機構を議論しようとするものである.ここで,非ニュートン流体の多孔質軸受内の流動状態,弾性変形の多孔質体の透過率に及ぼす影響,近接速度の圧力分布,負荷容量,弾性変形および流量に及ぼす影響などの潤滑特性を理論的に取り扱っている.併せて,実験を行って,理論を検証している.
抄録全体を表示
-
福井 茂寿, 木暮 賢司, 三矢 保永
1985 年 51 巻 469 号 p.
2291-2299
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
走行面のうねりに対するヘッドスライダのすきま変動には,スライダ長対うねりの波長の比,すきま形状などによって決まる下限値が存在する.流入端にテーバ部をもつスライダでは,この下限値は潤滑面内の場所に大きく依存し極小値をとる位置が存在すること,流出端部のすきま変動はスライダ長の二乗にほぼ比例することを明らかにした.これらの結果として,追従性の高い浮動ヘッドスライダの設計指針を示した.
抄録全体を表示
-
有浦 泰常, 小田 哲, 中西 勉, 矢野 満, 上野 拓
1985 年 51 巻 469 号 p.
2300-2308
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
第1報に基づいて,被削性に優れた鋳放し高強度球状黒鉛鋳鉄材を中硬度歯車の分野に実用化するため,その負荷能力を検討した.その結果,本球状黒鉛鋳鉄材は素材制作費の低減に寄与し,曲げ強さ・歯面強さともに調質合金鋼に劣ることなく,歯車材として十分実用可能であることがわかった.特に,ホブ切り状態でも歯面が滑らかで,調質鋼に比べ歯面強さが高いことは,本球状黒鉛鋳鉄材の有利な点である.
抄録全体を表示
-
寺島 健一, 西田 知照, 塚本 尚久, 石 嘉〓
1985 年 51 巻 469 号 p.
2309-2315
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
プラスチック歯車は耐食性,自己潤滑性,低騒音など金属歯車にない特色を持っているが,歯のかみあい挙動が金属歯車と異なるため損傷状態も大きく異なり寿命の予測もむつかしい.本報ではプラスチック歯車を動力伝達用として使用するとき問題となる歯元の異常摩擦の発生成長機構ならびにそれが誘因となってピッチ点近傍に発生する歯の折損機構との関係を解明し,プラスチック歯車の寿命延長法を提案している.
抄録全体を表示
-
梅澤 清彦, 鈴木 登志夫, 佐藤 太一
1985 年 51 巻 469 号 p.
2316-2323
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
比較的歯幅の狭い動力伝達用はすば歯車の回転方向振動挙動を明らかにするために,差分法を適用して求められている歯車対のたわみからかみあっている歯対のばねこわさの近似式を製作した.さらに,その妥当性を加速度を測定することで検証した.その結果,回転方向振動は,一自由度の振動系として取扱えることを明らかにし,近似式により得られたかみあい固有振動数と実験により得られた値とがよく一致することを示した.
抄録全体を表示
-
韋 雲隆, 酒井 高男, 大泉 哲哉
1985 年 51 巻 469 号 p.
2324-2331
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
著者らは大形歯車を対象にし,経済的で製作・組立・補修の便を考慮したピンホイール鼓形ウォームギヤを提案した.理論的には歯形論的考察を容易にするため,共面性直線なる概念を導入した.この概念により,接触線の現れ方,接触範囲を概観した.また数値的に歯形論的諸性質を調べ,歯当りの様子を包絡過程の計算機シミュレーションによって求めた.かみあい性能への配慮から斜交軸を提案した.
抄録全体を表示
-
寺内 喜男, 白石 光信, 芦沢 忠昭
1985 年 51 巻 469 号 p.
2332-2340
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
歯車の転造仕上げに際して,歯幅および硬さが歯面の変形に及ぼす影響を明らかにすると同時に,転造による変形を本質的に把握する目的で,幅および硬さの異なるローラを用いてすべり率を変えて転造実験を行い,変形形状,塑性変形量および加工硬化性の面から検討を加えた.その結果,変形は繰返し数3~6回程度で安定するが,幅によって変形状態が異なることがわかった.また変形諸量感の関係についても明らかにできた.
抄録全体を表示
-
佐山 武英, 林 国一, 梅澤 清彦
1985 年 51 巻 469 号 p.
2341-2349
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
薄肉リム歯車のリム厚さを決定するのに必要な変形と応力特性を知るため,歯をもたない円筒かくの一端固定,他端自由な場合についての任意の位置と向きに集中荷重を加えたときの変形量と諸内力値を求めた.歯の存在を無視したので現実の歯車からはやや遠いモデルであるが,集中荷重が加わったときのリム厚さなどを決定するための基本的特性を把握できた.ただし,用いた弾性方程式が近似式のため円筒かく寸法に制限されることも指摘した.
抄録全体を表示
-
山倉 康隆, 長内 敏雄
1985 年 51 巻 469 号 p.
2350-2356
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
ピッチングの大きさに注目した解析方法として平均面積をもとめる方法を提案し,この方法の一般性,および実用化を寸法,形状の異なる3種類の調質に対し潤滑油温度を変えて行ったピッチング試験の結果を用い,面積率を求める方法と比較検討して示した.次いで,ピッチングの非進行性領域や,平均サイズは負荷くり返しにより成長しないなどの性質や,材質および潤滑油温度などの平均面積に及ぼす影響を調べ示した.
抄録全体を表示
-
田中 道彦, 山田 朗
1985 年 51 巻 469 号 p.
2357-2363
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
本論文では,周辺境内の大部分が自由表面であるねじ締結体の境界要素法解析において,基本解に Mindlin 解を用いる場合について研究した.これにより,自由表面部の要素分割が不要になり入力データが著しく減少したほか,三次元および軸対称境界要素法によるねじ解析が可能となった.また領域分割解法を応用することにより,ねじ締結体の接触問題の解法が容易になったほか,外力の作用に伴うボルト軸力や接触域の変化が解析された.
抄録全体を表示
-
高倉 章雄, 小畑 誠司, 山口 克彦, 福田 正成
1985 年 51 巻 469 号 p.
2364-2372
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
金属薄板の塑性変形に伴う表面あれ,および成形限界に対する変形経路の影響を,剛塑性有限要素法によって解析した.解析では,個々の結晶粒の変形抵抗が異なる不均質な板材モデルを考え,また変形経路として第2軸引張り,平面ひずみ引張り,一軸引張りの単純変形経路を組み合わせた複合変形経路を採用した.その結果,表面あれの発達挙動および成形限界は変形経路によってきわめて大きく影響されることがわかった.
抄録全体を表示
-
大村.悦二 , 難波 義治, 牧之内 三郎
1985 年 51 巻 469 号 p.
2373-2380
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
前報で提案した硬化層生成理論を適用し,ビーム径とビーム移動速度の二つのパラメータに注目して,硬化層が生成する照射条件の範囲と,硬化層の深さと幅が最も大きくなる照射条件を推定することを試みた.硬化層が生成する照射条件の範囲と硬化層の大きさを推定した結果は,実験結果とよく一致し,照射条件の最適値の妥当性も示された.照射条件の最適化は,他の目的関数についても同様に行うことができ,実用上有効である.
抄録全体を表示
-
佐藤 壽芳, 大堀 真敬
1985 年 51 巻 469 号 p.
2381-2388
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
SEM の反射電子画像信号をファイバを介してミニコンピュータにとりこみ,従来アナログ方式の積分演算によってえていた表面あらさ曲面をディジタル方式によっても可能とした.これによって,画面上で走査線を特定してあらさ曲線が求められること,信号の平均化処理でノイズの影響を低減できることなどの諸点について性能向上がはかれることを示した.
抄録全体を表示
-
本間 義彦
1985 年 51 巻 469 号 p.
2389-2392
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
自動組立における部分整列の簡単な方法の一つとして,走路に段差を設けて部品を転倒させることによる方法がある.このとき通過する部品が転倒するための条件を,部品の形状,重心位置,段差の大きさのほか,転倒前後の回転速度の変化,部品の走路上での移送速度などを考慮して求めた.得られた条件式は,数列について実験を行い計算結果と比較して,所要の段差を推測するのに十分有効であることを示した.
抄録全体を表示
-
高田 一, 大野 一彦
1985 年 51 巻 469 号 p.
2393-2396
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
This paper deals with the natural frequency of an edge-fixed disc in contact with a liquid, which acts as an added mass to the disc reducing its natural frequency. Calculations and experiments are carried out for the following two cases : Disc-shaped liquid is kept on the disc (1) with its free surface parallel to the disc and (2) surrounded by rigid walls without air content. In Case (1) the natural frequency of the disc decreases with increased liquid height, while in Case (2) vice versa. The experimental results agree well with the calculations by means of finite element method within 4.3% error for the nodeless mode and for the mode with one diametral- and zero circular node. A reduction formula of the reducing ratio of the frequency is derived for arbitrary disc thickness, radius and density and also for arbitrary liquid density.
抄録全体を表示
-
田中 信雄, 菊島 義弘
1985 年 51 巻 469 号 p.
2397-2402
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
In order to suppress the vibration as pollution generated by machines, an active force control method-a hybrid force control method-was proposed in the previous paper. This method aims to eliminate the exciting force of machines in almost all of the frequency range. This paper deals with the realization of the hybrid force control method from a practical point of view. First, based upon the experimental data, the design procedure of the system is presented. Secondly, on the suppression of the vibration as pollution, the control effect in terms of an active damper is considered. Thirdly, from a viewpoint of dynamic compensation, the effectiveness as well as the stabilization procedure of the system is shown. Finally, the realization of the hybrid force control method including both the characteristics of a low-pass filter of an elastic support and that of a high-pass filter of an active force control method is performed experimentally.
抄録全体を表示
-
佐藤 啓仁, 山本 純雄, 鎌田 治, 高津 宣夫
1985 年 51 巻 469 号 p.
2403-2407
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
Forced vibration of a gear system excited by transmission error having a period equal to the meshing period and by a random force, is analyzed approximately by means of an averaging method. Some numerical examples are given. To facilitate analytical treatment, the time varying parameter system is transformed into a time invariant parameter system.
抄録全体を表示
-
大山 忠夫, 杉本 嘉孝, 夏井 由郎, 中村 弘治, 中野 敏, 今井 克己
1985 年 51 巻 469 号 p.
2408-2413
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
In order to improve adhesion force between wheel and rail under water lubrication, a special composite type of conditioning block was developed for rubbing wheel treads during braking under the pressure of adhesion force with the block was investigated by the experiments using a large scale rolling contact testing machine. Then, some braking tests were carried out with railway cars at the speeds of beyond 120 km/h. by applying the block to wheel treads during braking, gross slips were reduced and preferable adhesion characteristics were obtained under wet condition. The adhesion coefficients with the blocks were about 1.4 times higher than the values without the blocks under water lubrication.
抄録全体を表示
-
伊藤 周三, 村上 靖典, 伊東 誼
1985 年 51 巻 469 号 p.
2414-2418
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
The necessity of establishing the determination methodology of the mathematical model of the machine tool joint becomes more important recently. In this study, thus, the interface pressure distribution of the bolt-flange assembly under complex loading condition was measured by means of the ultrasonic waves method. From the results, it can be observed that the initial tightening force and roughness of joint surface have large influence on the change of the interface pressure distribution due to the external loading (bending moment). On the basis of the experimental evidences, furthermore, the data available for the determination of the mathematical model have been arranged. For instance, the data available for the determination of the mathematical model have been arranged. For instance, the pressure effective area is largely moved when the bending moment commences to effect, but it is not so large at the further loading. In addition, in both the cases, the pressure effective area are, in general, maintained as the same as that under no external loading.
抄録全体を表示
-
榊田 勝美, 石川 広美
1985 年 51 巻 469 号 p.
2419-2422
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
The effects of a 60 Sn solder overlaid at the copper surface were studied experimentally on the cutting force and on the chip thickness ratio. The presence of the boundary layer between the solder and copper produced a higher chip thickness ratio and reducd the cutting force. It has been reported that similar effects are found when fatty acids are applied to the surface of a copper or alminumspecimen. It can be demonstrated that an increase in the size of the solder layer also increases the chip thickness ratio.
抄録全体を表示
-
堤 成晃, 加藤 隆雄
1985 年 51 巻 469 号 p.
2423-2429
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
An experimental equipment to assess the tool-workpiece compatibility in deep drawing was designed, built, and characterized. In this construction, a die is divided into two coaxial parts and the one with die profile radius can be rotated at a desired speed so that the meridian component of frictional force reduces to zero. In order to test the performance of this equipment, some trial draws of copper sheets were carried out, and it was proved that the all functioned as designed. While the forces carried by the flat part and the curved part of die gave a vivid description of the interaction between tool and workpiece, absolute value of frictional force on the die radius was estimated for the first time by subtracting punch load with rotation from one without rotation.
抄録全体を表示
-
片峰 昭彦, 小野沢 元久, 石井 勇五郎
1985 年 51 巻 469 号 p.
2430-2433
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
There are many methods for measuring the depth of fatigue crack by ultrasonic testing. The flaw heights are measured by ultrasonic angle beam testing. This method has various problems. For example, pulse amplitude is affected by flaw size and the inclination of a flaw. This time, the authors developed a special probe. This work has been carried out to investigate the flaw detection sensitivity of the probe. The results indicate that the probe can estimate fatigue crack depth in an accuracy of 0.52.0 mm.
抄録全体を表示
-
斉藤 正美, 済木 弘行, 河合 望
1985 年 51 巻 469 号 p.
2434-2441
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
A new apparatus for ironing test has been made to resolve the critical conditions in the ironing process of thin wall metal cups. Ironing punch load (P) and frictional force (F
P) acting on the punch surface can be directly measured. Two main components of F
P, i. e. (F
Pd) on the ironing region and (F
Pf) on the region after ironing, are separated from one another by using F
pf estimated from the measured stripping load of the ironed cup. Thus, the axial stress in the cup wall at die exit can be exactly calculated. The results are as follows. (1) As the friction on the punch becomes higher, the axial stress in the cup wall becomes smaller and the welding becomes easy to occur. (2) The axial fracture stress in an ironed cup wall is larger than the critical stress of the original cup calculated by using the maximum load condition under uniaxial and plane strain states.
抄録全体を表示
-
進村 武男
1985 年 51 巻 469 号 p.
2442-2443
発行日: 1985/09/25
公開日: 2008/02/21
ジャーナル
フリー
This paper discusses analytically on the machining condition for modification of work roundness error by a simple conventional cylindrical lapping method, in which the internal surface of the cylindrical workpiece is machined with the lapping tool supported with two free rotating rollers. The analysis points out that there is a suitable machining condition for modification of roundness error by which the effect of the random and periodic deflections of the supporting roller surface and its rotating axis on the word roundness can be decreased.
抄録全体を表示