計測自動制御学会論文集
Online ISSN : 1883-8189
Print ISSN : 0453-4654
ISSN-L : 0453-4654
53 巻, 4 号
選択された号の論文の5件中1~5を表示しています
論文
  • 岩政 宏紀, 土谷 茂樹
    2017 年 53 巻 4 号 p. 261-267
    発行日: 2017年
    公開日: 2017/04/18
    ジャーナル フリー
    Operation of an actuator having a series tensile constitution of a planar type dielectric elastomer actuator and a spring was analyzed by taking viscosity of elastomer into consideration. It was found that the influence of the viscosity is reduced by applying a pre-stretching in the tensile direction. Furthermore, the pre-stretching conditions for achieving the largest operation strain and the largest generation force were obtained in cases with and without application of load. In addition, the number of lamination of the planar type DEA for satisfying target specifications about the maximum displacement and the maximum traction force was derived.
  • 江上 正, 渡邊 孝之, 梅本 和希
    2017 年 53 巻 4 号 p. 268-275
    発行日: 2017年
    公開日: 2017/04/18
    ジャーナル フリー
    We propose a method for vehicle path control that considers sideslip through the combination of a time-state control form and a path control method with nearest point search and we demonstrate the method's effectiveness through experiments with an experimental small four-wheeled vehicle. In the proposed method, combining the time-state control form and path control method with nearest point search for a geometric model that constrains the position of the vehicle in consideration of sideslip allows arbitrary path following through the translational velocity and yaw rate determined from input. The method gives steering angle as input to the yaw rate control system with derived yaw rate taken as a desire value for an equivalent two-wheeled model that considers sideslip. Because cornering power and sideslip angle are difficult to determine in a yaw rate control system, these are estimated using adaptive identification and a state observer, and an adaptive control system is formed. The small four-wheeled vehicle performs path control by use a laser scanner to estimate its position and attitude. The effectiveness of a sideslip angle estimation method that uses motion capture is also demonstrated. We verify that estimates of sideslip angle are nearly identical to measured values, and experiments using a variety of path desired values demonstrate the effectiveness of the proposed path control method.
  • 神保 智彦, 日比野 良一, 山口 裕之, 大坪 秀顕, 加藤 伸二
    2017 年 53 巻 4 号 p. 276-285
    発行日: 2017年
    公開日: 2017/04/18
    ジャーナル フリー
    This paper proposes low-order physical modeling method using operational output-only data without inputs. Vehicle characteristics and the controllers are designed to be satisfied with a number of requests and constraints such as driveability and ride comfort. Those need dynamic models which can represent the corresponding motional behaviors. However, the detail physical modeling for various vehicles and the simplification, or the system identification with input measurement is usually difficult or expensive in terms of labor. Therefore, in this paper, firstly, time-frequency data array of output accelerations of vehicle components is constructed and then decomposed by one of tensor decomposition methods, parallel factor (PARAFAC) decomposition, to separate stationary vibrations and transient vibrations like vibration modes. Secondly, using the result and the structure of PARAFAC, trade-off decision can be made between the model accuracy and the simplicity regarding number of motions considered in modeling. The effectiveness of this approach is demonstrated for driveability by using operational tip-in acceleration data.
  • 青木 今日子, 牧野 浩二, 中村 祐敬, 大森 英功, 花形 悦伸, 植田 祥平, 石田 和義, 寺田 英嗣
    2017 年 53 巻 4 号 p. 286-294
    発行日: 2017年
    公開日: 2017/04/18
    ジャーナル フリー
    It is important that the activities of daily living of the elderly are preserved and improved. One factor that decreases the activities of daily living is the knee Extension Lag. Many elderly patients have a knee Extension Lag after Total Knee Arthroplasty. In most cases, the recovery of the extension lag is not necessary surgery, and is often enough to as perform the rehabilitation. However, physical therapists find it difficult to perform rehabilitation of patients with an Extension Lag. In this study, an instrument for automatic rehabilitation of the extension lag was developed by adapting the Knee-Assistive Instrument for Rehabilitation (KAI-R) that has been developed as the walking rehabilitation after that surgery. First, the specifications for the rehabilitation of the extension lag were considered and a control algorithm was proposed. Second, the algorithm was installed into the instrument and its effectiveness was confirmed by myoelectric potential. Finally, the instrument was examined in a clinical trial. A recovery trend of the patient and a reduction in work load of the physical therapist were confirmed.
ショート・ペーパー
feedback
Top