繊維機械学会誌
Online ISSN : 1880-1994
Print ISSN : 0371-0580
ISSN-L : 0371-0580
38 巻, 3 号
選択された号の論文の6件中1~6を表示しています
  • (第2報) 実験
    森 教安, 矢上 光宏, 江口 孝彰, 中村 喜代次, 堀川 明
    1985 年 38 巻 3 号 p. T47-T52
    発行日: 1985/03/25
    公開日: 2010/02/12
    ジャーナル フリー
    目的 内管が回転する偏心二重円管内における非ニュートン流体の圧力流れについてHEC水溶液を用いて実験を行い, 流れを解明するとともに, 前報の数値計算結果の妥当性を確認する.
    成果 1) 内管回転により, 無回転時に比べて同一圧力勾配での流量が増加した.また, 無回転時流量QSと回転時流量QRの関係において, 軸方向流れに与える回転の効果が大きいほど偏心率による違いが顕著となった.
    2) 二次流れ領域の角度は, 回転数が低いほど, 軸方向流れが大きいほど大きくなった.
    3) 外管壁上の圧力差分布は軸方向流れにより変化した.
    4) 圧力損失, 二次流れ領域の角度および外管壁上の圧力差分布の測定結果は, 数値計算結果と一致し, 数値計算の妥当性が確認できた.
  • (第2報) 糸口出しサクションノズル部の流動抵抗係数ならびに管に設けたスリットの流量係数が糸誘導に及ぼす影響
    平井 恒夫, 部谷 尚道, 木村 照夫, 幸川 光雄, 深井 完祐
    1985 年 38 巻 3 号 p. T53-T62
    発行日: 1985/03/25
    公開日: 2009/10/27
    ジャーナル フリー
    目的 自動ワインダの導糸管の最適設計に資するため, 糸口出しサクションノズル部に相当する部分の抵抗係数fと管軸に沿って設けたスリットの流量係数cの値が糸の誘導に及ぼす影響を実験ならびに数値計算により明らかにする.成果 f, cの値がそれぞれ管内流動および糸の誘導に及ぼす影響を実験ならびに数値計算により詳細に示すとともに, 管曲がり上流端と下流端における流量比, 糸の管外への飛出し時の張力およびそのときの糸の管内飛走距離を, f, c, R/r (R : 導糸管曲がり半径, r : 管半径) の関数として定式化することにより導糸管の最適設計のための指針を与えた.
  • 広津 敏博, 須田 昌男
    1985 年 38 巻 3 号 p. P135-P143
    発行日: 1985/03/25
    公開日: 2009/10/27
    ジャーナル フリー
  • 松本 修
    1985 年 38 巻 3 号 p. P144-P150
    発行日: 1985/03/25
    公開日: 2009/10/27
    ジャーナル フリー
  • 飯田 進也
    1985 年 38 巻 3 号 p. P151-P158
    発行日: 1985/03/25
    公開日: 2009/10/27
    ジャーナル フリー
  • 大沢 政徳
    1985 年 38 巻 3 号 p. P159-P165
    発行日: 1985/03/25
    公開日: 2010/02/01
    ジャーナル フリー
    To learn a systematic method for effective training of machine sewing, general charateristics of adult women operators by an electric sewing have been in vestigated. Adult women operators were asked to sew along straight or curved lines printed on pre pared papers under several conditions. The results obtained were as follows :
    1) The deviation of stitched lines from predeter mined guide lines increases with the increase of the curvature of the guide line. In addition, the increasing rate of the deviation as a result of the increase of the stitching speed also increases in proportion to the curvature.
    2) The phase lag of stitched lines from predeter mined guide lines when sewing along sinusoidal curve increases as the stitching speed increases.
    3) The tracking ability of operators along predeter mined guide lines is proportinal to an accumulation of the experience they have already gained.
    4) Sewing at high speed along sharp curve tends to cause an irregular stitch and indented stitch line.
    5) The deviation increases as intervals between predetermined guide marks increase and it becomes more remarkable on curves than on straight lines.
    6) While sewing along straight lines, if intervals between predetermined guide marks are long enough or if stitching lines are apart from guide lines, the deviation decreases as sewing speed in creases.
    7) The sewing speed control is more difficult when stitching along curved lines than along straight lines.
feedback
Top