A comparative study of the static and dynamic response of a slope is carried out, using the large deformation theory of the updated Lagrangian formulation and the conventional infinitesimal theory. In the static analysis, a strength reduction method proposed by one of the authors is used to evaluate the safety factor of the slope. It is found that by the large deformation theory, the safety factor is larger than that calculated by the infinitesimal theory, and this difference becomes large along with the reduction of elastic modulus. In the dynamic analysis, it is observed that the large deformation theory gives smaller sliding displacement and larger response acceleration than the infinitesimal approach. It is concluded that in many cases the large deformation approach gives more adequate solutions.

抄録全体を表示

The paper presents results from an extensive experimental model study of response of dry sand to impact of a rigid tamper. In the laboratory tests a circular steel tamper was repeatedly dropped on sand contained in a large tank. Measurements included tamper acceleration aud soil pressure at impact, tamper settlement, aud soil densities and strains. Effects of tamper drop height, weight and contact area were investigated. A method is presented for the evaluation of global dynamic stiffness of the soil mass affected by the impact by calculating a dynamic settlement modulus (DSM). The DSM values are determined from integration of the impact acceleration record with respect to time using measured integration constants. DSM values show good correlation to soil densities and corresponding elastic moduli obtained from laboratory tests for loose sand. However, for dense sand, results indicate apparent discrepancies between elastic modulus and the higher DSM values. Analyses of normalized impact energy and the resulting densification in the sand in terms of normalized dimensions of volumetric strain (relative density) contours show unique correlations which are used for a proposed rational design method for dynamic compaction in dry sandy soils.

抄録全体を表示

Based on the concept "intermediate soil wedge" which is dependent on mobilized frictional resistance, a new theory has been developed for evaluating the seismic earth pressures against retaining walls under any condition between the active and passive states. For this theory, the seismic earth pressure is separated into four components according to their formation. New equations are proposed to determine the distribution, resultant and point of application for each component. An equivalent seismic coefficient is introduced to take into account non-uniform seismic acceleration distribution with depth. The equations place special emphasis on dependence of the seismic earth pressure on mode and level of wall movement. The equations can be reduced to the Mononobe-Okabe equation for the limiting conditions. Their applicability was confirmed by comparing the predictions with a number of previous model test results.

抄録全体を表示

During earthquakes, saturated loose sandy soils often liquefy, causing serious damage to buildings and underground structures. Various construction methods have been employed to stabilize these soils against liquefaction. The popular methods are those which increase their density. Vibration and impact methods are commonly employed, but these often pose a problem of noise and vibration in urban areas. Results of previous experiments have shown that Quick Lime Consolidated Briquettes (QCB), a soil stabilizer made of quicklime and cement placed to form cylinders, significantly increases resistance to liquefaction by utilizing the effects of water absorption, swelling, and hardening. In the present study, shaking table tests were performed to evaluate the earthquake resistance of soil treated with QCB. Results of these test showed that the response acceleration and excess pore water pressure in QCB-treated soils were scarcely affected by the excitation of 200 Gals. The soil settlement due to shaking was about one tenth of that for the untreated soil, proving the effectiveness of QCB during earthquakes.

抄録全体を表示

A finite element model capable of taking into account nonlinear hysteretic soil behavior is presented to study earthquake induced retaining wall movement. The model also accounts for increase in lateral stresses and settlement associated with grain slip caused by cyclic loads. The predictive capability of the proposed method is verified by comparing responses given by the model with those computed by another existing finite element model and also with responses recorded at the Cambridge centrifuge facility. The study reveals that the wall displacement can be substantially affected, among other factors, by the increase in lateral stresses due to grain slip and wall-soil friction. Care should be taken when selecting a constant value of wall-soil friction angle for the entire duration of excitation since structural changes can occur in the soil adjacent to the wall.

抄録全体を表示

In view of the significant role of the water film effect in flow failure for a liquefied sandy deposit, the mechanism of water film generation is numerically studied based on a 1-dimensional model test. The process of water film growth and decay can be simulated to a certain extent by a simple consolidation analysis, which indicates that only a small difference in permeability in layered sand is enough for a water film to develop. A 1 G shaking table test for a two-dimensional slope model with an arc of silt within a saturated sand is then addressed to discuss the dilatancy effect exerted in sheared sand during flow failure. It is possible that, once the water film is formed, the transmission of shear stress through it is interrupted, leaving the sand below free from the dilatancy ; this eventually allows the water film to stay without being absorbed during flow failure. The result of another shaking table test for a trapezoidal slope with horizontal silt seams indicate that water films beneath the seams enable the soil mass above them to laterally flow along water films very gently inclined even after shaking. If a silt seam breaks due to excessive pressure in the water film, it triggers re-liquefaction in the upper sand and leads to further instability.

抄録全体を表示

The behavior of the soft clay grounds subjected to repeated loading is different from that subjected to sustained loading. The difference in settlement between these two loading patterns should be due to secondary compression over a long period of time. Consequently, soft clay grounds subjected to repeated loading tend to be more compressible than those subjected to sustained loading. Therefore, it is necessary for engineers to predict post-construction settlements under repeated loading. In this respect, the preloading is considered to be promising as a countermeasure to reduce the settlement of clay under repeated loading as well as under sustained loading. The effect of preloading on post-construction consolidation settlement of soft clay subjected to repeated loading after removal of a part of preload is investigated in the present paper. It has become clear that the settlement of a clay sample after preconsolidation is mainly affected by the amount of preload, the degree of consolidation due to the preload, the amount of permanent load and the amount of repeated load after removal of preload. The calculated settlement versus time relations using a method to estimate the amount of consolidation settlement of soft clay grounds subjected to repeated loading after removal of preloading were compared with the observed degree of consolidation as parameters of the intensities of preload and repeated load.

抄録全体を表示

 The stability of

‒tetrahydrocannabinol acetate (‒THC‒OAc) and ‒tetrahydrocannabinol acetate (‒THC‒OAc) in -liquid during storage was investigated. ‒THC‒OAc liquids in cartridges were stored at 80℃ or 30℃ for 28 days. The relative concentrations of cannabinoids in the liquids were measured by gas chromatography with flame ionization detection. ‒THC‒OAc decreased during storage at either temperature. ‒THC, a minor impurity, also decreased. ‒THC‒OAc liquid in a cartridge was stored at 80℃ for 57 days. The concentration of ‒THC‒OAc and ‒THC, a minor impurity, did not change during that time. Cannabinol acetate increased in all liquids, and unknown products were also detected by gas chromatography/mass spectrometry (GC/MS). The ‒THC‒OAc and ‒THC‒OAc liquids were subjected to GC/MS to detect representative diluents, glycerol, propylene glycol, and polyethylene glycol 400, but none of these were detected.

抄録全体を表示

Repetitive liquefactions in angular and subangular gravels from an alluvial fan, in the case of two earthquakes with accelerations lower than that of a former which had caused liquefaction some months before, are described. The liquefaction took place from the surface, down to a depth of approximately 10 m. Water laden with sediments spouted out for some tens of minutes after the strong motion ceased. Knowledge of the grain size distribution of the sediments inside the body of the alluvial fan roughly defines the areas of the fan prone to future liquefaction. Non-repetitive liquefaction in overconsolidated fine fluvio-lacustrine sand of glacial origin at the unusual depth of 14 m to 16 m is also described. From the observation of sand lifted up for 10 m inside a large diameter well, and of that which spouted out from several microvents, it was estimated that extra-pore pressure was close to lithostatic conditions. Nevertheless, modeling of intrinsic pore pressure buildup on the DESRA2 programme gives lower values than the experimental one. Geotechnical characteristics of the 12 m-thick sandy stratum indicate that the upper part is unusually soft, either due to water circulation or past repetitive liquefactions which prevented reconsolidation. It is suggested that excess pore pressure generated by the earthquake was also due to redistribution of pressure from adjacent sediments.

抄録全体を表示

In this study the field feasibility of an innovative thermal technique to improve the performance of prefabricated vertical drains (PVD) used in conjunction with the preloading ground improvement method is investigated. For this purpose, two identical 6. m high full-scale test embankments for preloading were constructed over the soft Bangkok clay where a conventional PVD system was installed underneath one embankment and a novel prefabricated vertical thermo-drain (PVTD) system was utilized for the other. The PVTD unit consists of a U-tube made of cross-linked polyethylene plastic (PEX) that is attached to a conventional PVD unit. Preheated water at about 90°C is circulated through the attached U-tube to raise the soil temperature underneath the PVTD embankment. The behavior of the two test embankments were compared in terms of excess pore water pressure and consolidation results. The comparison shows the advantage of a PVTD system over a conventional PVD system. The rate of consolidation increases significantly in the PVTD system due to the temperature effect on the hydraulic conductivity. Moreover, the embankment with the PVTD system generates more settlement due to the thermally induced irreversible contraction of saturated normally consolidated soft Bangkok clay.

抄録全体を表示

Leakage of water due to internal erosion through a dam body or foundation is a major problem with fill-type dams. Recent case histories and research suggest that most cases of internal erosion are possibly triggered by hydraulic fracturing. However, the quantitative mechanism of hydraulic fracturing still remains to be solved. Therefore in-situ hydraulic fracture tests were carried out with a cheap, concise apparatus using boreholes dug in the soft clayey volcanic soil foundation of a low earth dam (Oyachi Dam) in Niigata Prefecture. Water was injected into the foundation through a perforated pipe by two methods : one was under a controlled injection pressure and the other was a controlled injection flow rate. In the former method, the relationship between flow rate and injection pressure was observed and it was found that a yield pressure or fracture pressure existed in all the tests. By repeating the injection test it was confirmed that once a crack is developed, it is very easily reopened by a water pressure a little higher than the earth pressure exerted on the crack. In the latter method, the relationship between injection pressure and time was observed and it was found that fracture pressure varied with flow rate. The boreholes were excavated to observe the development of fracture cracks and it was also found that the cracks had developed perpendicular to the borehole periphery, which means that fracture cracks were induced by tensile stress and denies the explanation that fractures are caused by shear failure.

抄録全体を表示

 We examined the stability of

-tetrahydrocannabinol acetate (-THC-OAc) and -tetrahydrocannabinol acetate (-THC-OAc) in -liquid products. Eight samples were heated at 30℃ for 28 days and one of them was heated at 70℃ for 2, , , 10, and 15 days. Residual ratios of -THC-OAc and -THC-OAc were evaluated by gas chromatography with flame ion detection and their degradation products were examined by gas chromatography/mass spectrometry (GC/MS). Some samples were tested for solubility in hexane and were submitted to GC/MS analysis to detect propylene glycol and glycerol. After a 28-day incubation at 30℃, -THC-OAc was slightly decomposed (residual ratio: 84.–94.2%) but -THC-OAc was almost stable (residual ratio: 95.2–108.%). Heating at 70℃ decomposed not only -THC-OAc but also -THC-OAc. The decomposition proceeded rapidly in the initial 2 days then slowly until 15 days later. The degradation products, four putative one-oxygen-atom adducts and cannabinol, were detected but deacetylated products (-tetrahydrocannabinol and -tetrahydrocannabinol) were not detected. All the samples tested were completely dissolved in hexane differently from propylene glycol and glycerol. Propylene glycol and glycerol were not detected from the samples completely dissolved in hexane. This study indicated that deacetylation of -THC-OAc and -THC-OAc did not proceed when the sample did not contain propylene glycol and glycerol.

抄録全体を表示

In the seismic analysis of pile foundations the soil is often assumed to be an elastic material and the pressure at the soil pile interface is not limited during the analysis. This may result in a considerable error, as the computed pressure from an elastic analysis may go well beyond the ultimate lateral pressure of real soil. In fact, significant yielding at the soil-pile interface has been observed during real earthquakes, and also in laboratory tests. The yield zone is usually near the ground surface where the effect of inertial force due to the superstructure is higher. This yielding redefines the pile response, and in general cannot be ignored. In order to examine the effects of soil yielding on the internal pile response during earthquakes an approximate analysis is described in this paper which is an extension of a static method developed by the second author (1982) for the analysis of piles subjected to lateral soil movement. This method is then used to investigate the effects of soil yielding on the internal response of piles through a comparative study in which real earthquakes are used. It is shown that for strong earthquakes and heavily loaded piles the soil yielding may considerably increase the amount of maximum pile moment developed in the pile. A marked difference in the effects of yielding on the pile moment and shear is observed and discussed.

抄録全体を表示

The interaction between a penetrating shaft and the surrounding soil media under impact loading is a frequently encountered phenomenon in geotechnical engineering. Examples of such dynamic soil/shaft interaction would include dynamic pile driving, standard penetration testing (SPT), and dynamic driven rod test. Presented in this paper is a novel approach, based on the principle of dynamic system identification, which enables identification of dynamic soil-pile interaction model parameters. The analytical transfer function, relating the output stress wave forms to the input stress wave forms in the soil/shaft system, is derived using the Laplace and Fourier Transform techniques and the one-dimensional wave propagation theories. A numerical solution algorithm based on a variation of gradient method is coded into a micro-computer based program to solve the frequency-dependent soil-pile interaction parameters (Smith model) : soil damping and soil spring stiffness. To further reduce the amount of computational effort required in the solution of the frequency-dependent dynamic soil properties, it is suggested that the solution be obtained for the first-mode natural frequency of the measured stress waves. The results obtained from this simplified solution algorithm, when compared with both numerical simulations and controlled laboratory tests, are reasonably acceptable. The proposed parameter identification technique offers a viable alternative data interpretation procedure for deducing pertinent Smith model parameters used frequently in pile driving analysis.

抄録全体を表示

The syntheses of (S)-13-hydroxy-(2, , )-tetradecatrienoic acid (1) and (2, , Z-tetradecatrienoic acid (2) were carried out by using the Wittig reaction as the key step. The asymmetric center at C-13 and the double bond between C- and C- for natural compound 1 were reconfirmed as being of (S) configuration and , respectively. The relationship between the structure of the unsaturated hydroxy fatty acids and their inhibitory effect on the growth of lettuce was investigated.

抄録全体を表示

An empirical equation in use for estimating the pseudo-elastic shear modulus, G_f, of subsoil, associated with shear strains less than .001% is proposed in this paper. In a series of in-situ seismic cone tests performed nationwide, the profiles of both G_f and the in-situ void ratio, , with depth were successfully characterised at five sites, each comprising a soft clay layer deposited in the Holocene era. The database which comprised the original data from the field and laboratory tests, coupled with similar information on well-documented Holocene clay deposits in Europe, was statistically analyzed in attempts to determine a generalised relationship with which G_f of soft clay may be reasonably estimated only from routinely available borehole data; that is and the current geostatic effective overburden pressure, σ'_v. An empirical relationship, G_f=, 000 -√(σ'_v) (kPa), was derived from the statistical analysis applied to data from seven different clays worldwide, for which extended over a range between 1 and , and the overconsolidation ratio ranged roughly between 1 and 2. The applicability of the proposed relationship was evaluated for two case records, each in which the clay exhibited unusual behavior; i.., the undrained shear strength remained more or less constant with depth due to the existence of artesian pressure at one site, and, at the other, G_f decreased, whereas increased, with depth. It was demonstrated that even in these clay deposits exhibiting exceptional profiles, the proposed relationship was capable of predicting G_f with a reasonable accuracy by determining the profiles of and σ'_v with depth. In addition, the prediction when compared to G_max from carefully performed laboratory cyclic tests, yielded a better estimate of G_f from the in-situ seismic survey. Despite the fact that the empirical relationship was initially designated to estimate G_f of soft clays, it may be equally applicable to sandy deposits. This was verified by comparing it to similar, and well-established, relationships developed for sands. A case record as such is also described for a loose sand deposit at Higashi-Ohgishima in Tokyo Bay which was placed in 1960's by land reclamation.

抄録全体を表示

Elastic wave propagation in saturated soil is investigated in order to grasp the frequency dependent wave propagation property of actual soil. First, a closed form solution of Biot's equation is derived under a one-directional wave propagation condition. Then, the frequency dependent properties of waves in various soils such as clay, silt, sand, gravel and soft rock are computed and discussed. The behavior is shown to be classified into three states : low frequency, high frequency and transient. Properties hardly change in the low and high frequency states. The degree of saturation is shown to hardly affect the shear wave property, but it greatly affects the dilatational wave property, especially in a highly saturated condition. Permeability hardly affects the properties at low and high frequency states, but it does change the frequency range of the transient state. Next, the applicability of Biot's formulation is examined and the high frequency state derived from Biot's equation is shown to be valid when permeability is larger than that of silt. Finally, it is shown that various mechanical properties can be evaluated using the frequency dependent characteristics of the wave, some of which are difficult to measure in situ with conventional tools.

抄録全体を表示

(³H) Tobramycin was used as a probe to determine the relationship between the structure of aminoglycoside antibiotics and their ability to remove this drug from its higher affinity binding site on the ribosome. The dissacharide moieties (neamine, tobramine, gentamine) appeared to have a common binding site, whereas the kanosamine, garosamine and ribose moieties determined the specificity of this binding. Amikacin and butikacin behaved in an anomalous manner in spite of their close structural relationship to tobramycin.

抄録全体を表示