Repetitive liquefactions in angular and subangular gravels from an alluvial fan, in the case of two earthquakes with accelerations lower than that of a former which had caused liquefaction some months before, are described. The liquefaction took place from the surface, down to a depth of approximately 10 m. Water laden with sediments spouted out for some tens of minutes after the strong motion ceased. Knowledge of the grain size distribution of the sediments inside the body of the alluvial fan roughly defines the areas of the fan prone to future liquefaction. Non-repetitive liquefaction in overconsolidated fine fluvio-lacustrine sand of glacial origin at the unusual depth of 14 m to 16 m is also described. From the observation of sand lifted up for 10 m inside a large diameter well, and of that which spouted out from several microvents, it was estimated that extra-pore pressure was close to lithostatic conditions. Nevertheless, modeling of intrinsic pore pressure buildup on the DESRA2 programme gives lower values than the experimental one. Geotechnical characteristics of the 12 m-thick sandy stratum indicate that the upper part is unusually soft, either due to water circulation or past repetitive liquefactions which prevented reconsolidation. It is suggested that excess pore pressure generated by the earthquake was also due to redistribution of pressure from adjacent sediments.

抄録全体を表示

(³H) Tobramycin was used as a probe to determine the relationship between the structure of aminoglycoside antibiotics and their ability to remove this drug from its higher affinity binding site on the ribosome. The dissacharide moieties (neamine, tobramine, gentamine) appeared to have a common binding site, whereas the kanosamine, garosamine and ribose moieties determined the specificity of this binding. Amikacin and butikacin behaved in an anomalous manner in spite of their close structural relationship to tobramycin.

抄録全体を表示

The activities of tobramycin derivatives acetylated and ethylated on the '-N, 2'-N and 3-N positions were examined. The MICs of these derivatives against tobramycin sensitive strains indicated that 2'-N-ethylated and '-N-ethylated derivatives have a fairly good activity, and confirmed that the 3-N position is the most important one for antibiotic activity since 3-N derivatives were less active. The MICs of these derivatives against tobramycin resistant strains, and their inactivation by tobramycin modifying enzymes were examined. These results showed that 2'-N or '-N ethylation protects the drug against inactivation by AAC(2') or AAC('), respectively, and 2'-N-ethyltobramycin and '-N-ethyltobramycin were active against strains containing these modifying enzymes. On the other hand, 3-N ethylation protects the drug against inactivation by AAC(3) but 3-N-ethyl tobramycin does not inhibit strains containing this enzyme.

抄録全体を表示

 The stability of

‒tetrahydrocannabinol acetate (‒THC‒OAc) and ‒tetrahydrocannabinol acetate (‒THC‒OAc) in -liquid during storage was investigated. ‒THC‒OAc liquids in cartridges were stored at ℃ or 30℃ for 28 days. The relative concentrations of cannabinoids in the liquids were measured by gas chromatography with flame ionization detection. ‒THC‒OAc decreased during storage at either temperature. ‒THC, a minor impurity, also decreased. ‒THC‒OAc liquid in a cartridge was stored at ℃ for 57 days. The concentration of ‒THC‒OAc and ‒THC, a minor impurity, did not change during that time. Cannabinol acetate increased in all liquids, and unknown products were also detected by gas chromatography/mass spectrometry (GC/MS). The ‒THC‒OAc and ‒THC‒OAc liquids were subjected to GC/MS to detect representative diluents, glycerol, propylene glycol, and polyethylene glycol 400, but none of these were detected.

抄録全体を表示

 We examined the stability of

-tetrahydrocannabinol acetate (-THC-OAc) and -tetrahydrocannabinol acetate (-THC-OAc) in -liquid products. Eight samples were heated at 30℃ for 28 days and one of them was heated at 70℃ for 2, 4, , 10, and 15 days. Residual ratios of -THC-OAc and -THC-OAc were evaluated by gas chromatography with flame ion detection and their degradation products were examined by gas chromatography/mass spectrometry (GC/MS). Some samples were tested for solubility in hexane and were submitted to GC/MS analysis to detect propylene glycol and glycerol. After a 28-day incubation at 30℃, -THC-OAc was slightly decomposed (residual ratio: 84.–.2%) but -THC-OAc was almost stable (residual ratio: .2–108.%). Heating at 70℃ decomposed not only -THC-OAc but also -THC-OAc. The decomposition proceeded rapidly in the initial 2 days then slowly until 15 days later. The degradation products, four putative one-oxygen-atom adducts and cannabinol, were detected but deacetylated products (-tetrahydrocannabinol and -tetrahydrocannabinol) were not detected. All the samples tested were completely dissolved in hexane differently from propylene glycol and glycerol. Propylene glycol and glycerol were not detected from the samples completely dissolved in hexane. This study indicated that deacetylation of -THC-OAc and -THC-OAc did not proceed when the sample did not contain propylene glycol and glycerol.

抄録全体を表示

The correction factor (η_ie) for the ultimate bearing capacity of a footing placed adjacent to a slope, taking into account the combined effect of horizontal and vertical seismic loads, represented by horizontal and vertical seismic coefficients, k_h and k_v, respectively, was derived using a modified Janbu's slice method. The influence of slope angles ‘α’ on the values of ‘η_ie’ are studied here. It was found that the values of η_ie can be expressed as an exponential function of ‘k_h/(-k_v)’ and ‘α’, with a measurable interdependency between ‘α’ and ‘η_ie’. The influence of ‘α’ on the value of ‘η_ie’ increases as the input value of ‘k_h/(-k_v)’ increases. Equations derived based on the analytical results are proposed to account for this effect. Based on the analyses of 11 near-fault seismographers obtained in the 1999 Chi-Chi earthquake in Taiwan, a ratio between the vertical and the horizontal seismic coefficients, λ, of between ±0.25 is suggested for including the combined effect of vertical and horizontal seismic forces in evaluating the seismic bearing capacity of footings located in near-fault areas.

抄録全体を表示

At present, analytical or empirical formula for seismic bearing capacity of footings adjacent to slopes is not available. This study uses a pseudo-static-based approach in conjunction with rigorous Janbu's slice method to derive analytical values of seismic bearing capacity factors (N_γ) and correction factors for the effects of inertia of soil mass and load inclinations for a rigid footing adjacent to cohesionless slopes. It is shown that both the bearing capacity factors (N_γ) and the correction factors for the seismic bearing capacity of footings placed on level ground derived herein are comparable with those reported in the literature. Empirical equations regarding the effects of slope angles and load inclinations, expressed using generalized forms of those proposed in the literature, are also derived. It is also found that the empirical equations derived in the present study provide values of correction factors in good agreements with the analytical ones, indicating the validity of using these empirical equations for assessing the bearing capacity of rigid footings situated on the slope subjected to pseudo-static seismic loading.

抄録全体を表示

In this paper, instead of the time-invariant state-space representation in the consequent of the T-S fuzzy model, tim,-varying system is considered in order to deal with the reconstruction error between the real system to be controlled and its T-S model, and fuzzy approximator is employed to cope with unknown functions involved in the model. As a result, it reaches an adaptive controller that has two parts: one is obtained by solving certain linear matrix inequalities (LMIs) (fixed part) and another one is acquired by the fuzzy approximator in which the related parameters are tuned by adaptive law (variable part). The proposed controller can guarantee the closed-loop system to be asymptotically stable.

抄録全体を表示

Circuit techniques to enhance the linearity of input-voltage-to-current (V/I) conversion and to increase the output impedance of a current source by compensating for the low intrinsic gain of a transistor were introduced to realize a high-frequency operational transconductance amplifier (OTA) for a low supply voltage using sub-100-nm CMOS processes. Applying these techniques, a MOS th-order Gm- linear-phase low-pass filter (LPF) was realized using a 65nm CMOS process. A simplified biquad LPF that can serve as a component of a th-order LPF was newly developed by replacing OTAs with resistors. As a result, the -3dB frequency bandwidth, group delay ripple, 3rd-order distortion, and 3rd-order input intercept point (IIP3) were 200MHz, 2.2%, ≤ -55dB with a 100MHz input, and +10.3dBm, respectively, all with a ±0.Vp-p input signal at each input terminal in the pseudodifferential configuration. The LPF including an output buffer dissipated 60mW in the case of a .2V supply. Wide spurious-free dynamic range (SFDR) characteristics were confirmed up to high frequencies.

抄録全体を表示

Two new partially saturated tricyclic ring systems, , a, , , , 10, 10a, 11-octahydro-11-oxodibenz [b, ] oxepins (3a and 3b), and -thiepins (4a and 4b) were synthesized. Compounds 4a and 4b were desulfurized to give a pair of isomeric 2-methylbenzoylcyclohexanes (10a and 10b). Deuterated 4a and 4b (11a and 11b) were prepared starting from butadiene- (12). The stereochemical features of 3a (trans), 3b (cis), 4a (trans) and 4b (cis) are compared with those of 10a, 10b, 11a and 11b on the basis of proton nuclear magnetic resonance data.

抄録全体を表示

Nアルキル3,4:,10-ペリレンテトラカルボン酸モノアンヒドリド=モノイミド[4a～]と芳香族アミン(アニリン,p-トルイジン,p-アニシジン,3,-キシリジン,4-アミノナゾベンゼン,およびo-フェニレンジアミン)を縮合して非対称型3,4:,10-ペリレンビス(ジカルボキシミド)誘導体-N-アルキル-N'-アリール-3,4:,10-ペリレンビス(ジカルボキシミド)(〔a～〕,〔a～〕,〔a～〕,〔a～〕,〔a～〕,および〔10a～b〕)を合成した. これらの各誘導体はすべて赤色系の色相を示し, 顔料試験の結果N-ブチル-N'-アリール-3,4:,10-ペリレンビス(ジカルボキシミド)(たとえば〔〕や〔〕)がとくにすぐれた耐光性を示した.

抄録全体を表示

The mechanism of wave-induced instability in a permeable seabed have been studied for more than two decades. The distinction between shear failure and liquefaction, however, has not been clearly defined. This paper presents a fundamental study on the differences in two failure modes for a fully saturated seabed of both finite and infinite thickness. The wave-induced effective stresses and pore pressure, obtained from an analytical solution of Biot's pore-elastic consolidation theory, were employed to examine the failure modes under a two-dimensional plane strain condition. A case study is presented to examine the failure modes with respect to several parameters, such as excess pore pressure, seepage flow, seepage force, failure areas and stress path in the seabed. The conclusions obtained from this study were as follows ; () the thickness of a permeable seabed affects the pore pressure and effective stress response to ocean waves and the failure mode of the seabed, (2) either a liquefaction or shear failure, or both, occur in the seabed, even in the saturated seabed, (3) the Mohr-Coulomb's failure criterion, when combined with elastic stresses, can not be employed to estimate the liquefaction failure in the seabed, (4) the liquefaction can be evaluated by a criterion in terms of the excess pore pressure, () The liquefied zone in the seabed is significantly different from the shear failure zone. The shape beneath the seabed surface for the former is almost identical to the contour where the upward seepage flow is concentrated.

抄録全体を表示

11-Amino-, a, , , , 10, 10a, 11-octahydrodibebenzo[b, ]thiepines (a-d) and -oxepines (a-d) were synthesized by the Leuckart reaction of , a, , , , 10, 10a, 11-octahydro-11-oxodibenzo[b, ]thiepines (a, b)and -oxepines (2a, b) followed by hydrolysis of the reaction products 4a-d and a-d, respectively. The four diastereomers, cis(a-H, 10a-H)-cis(10a-H, 11-H) a and a, cis(a-H, 10a-H)-trans(10a-H, 11-H) b and b, trans(a-H, 10a-H)-trans(10a-H, 11a-H) and , and trans(a-H, 10a-H)-cis(10a-H, 11-H) d and d, were isolated and their configurations and conformations were elucidated by chemical methods together with

1H

-nuclear magnetic resonance spectroscopic and X-ray crystallographic analyses.

抄録全体を表示

The objective of this article is to propose and evaluate a sliding-block model to deal with very large displacements of slopes when a horizontal earthquake is applied. The slip surface consists of two inclinations on which full shear resistance is mobilized. Internal shearing exists along a sub-plane that intersects the angle between the two sub-planes that form the external slip surface. The ratio of the distance moved along the two external sub-planes depends on the inclination of the internal sub-plane. If there is a water table line, undrained conditions are assumed during motion and total stress analysis is performed. The governing equations of motion are formulated, analytical solutions are obtained for some cases, and back-analysis of four well-documented slides is performed.

抄録全体を表示

This paper is concerned with an extension of a rotational limit equilibrium method for determining the permanent displacements of slopes under seismic excitation. In the proposed procedure, the sliding mass is treated as a rigid rotating body defined by a log spiral trace. Permanent displacements are obtained by double-integration of the equation of motion in a manner similar to Newmark's translational sliding block method. The seismic slope stability analysis is based on the rotational (variational) limit equilibrium approach. This stability analysis was verified with dynamic experimental results obtained from centrifuge model testing. A series of parametric studies was conducted on"unstable"slopes, investigating the effects of soil properties and characteristics of excitation on the magnitude of permanent displacements. The higher the frictional angle, the smaller the permanent displacement of the slope is. Low excitation frequency yields larger slope displacement if the excitation is extended for the same time period of time. The effect of frequency becomes less distinct when a larger value of yield seismic coefficient is used. The proposed procedures produce a rational criterion to evaluate the seismic performance of simple slopes. This criterion is based on permanent displacement limit rather than factor of safety alone.

抄録全体を表示

A comparative study of the static and dynamic response of a slope is carried out, using the large deformation theory of the updated Lagrangian formulation and the conventional infinitesimal theory. In the static analysis, a strength reduction method proposed by one of the authors is used to evaluate the safety factor of the slope. It is found that by the large deformation theory, the safety factor is larger than that calculated by the infinitesimal theory, and this difference becomes large along with the reduction of elastic modulus. In the dynamic analysis, it is observed that the large deformation theory gives smaller sliding displacement and larger response acceleration than the infinitesimal approach. It is concluded that in many cases the large deformation approach gives more adequate solutions.

抄録全体を表示