The main objective of this paper is to compare safety factors obtained from Morgenstern-Price, Janbu and Spencer methods with the factors calculated from the modified variational approach (Leshchinsky and Huang, 1992a). Such comparison is essential since there is no mathematical proof that the variational analysis indeed yields a minimum and thus, physically produce significant results. The safety factors compared well, indicating the variational analysis is on a par with acceptable existing rigorous methods. Availability of a user-friendly computer code may make the variational analysis useful to practicing engineers. However, its greatest potential at the moment is in 3-D applications; i.., unlike other methods, its extension to 3-D is straightforward.

抄録全体を表示

The correction factor (η_ie) for the ultimate bearing capacity of a footing placed adjacent to a slope, taking into account the combined effect of horizontal and vertical seismic loads, represented by horizontal and vertical seismic coefficients, k_h and k_v, respectively, was derived using a modified Janbu's slice method. The influence of slope angles ‘α’ on the values of ‘η_ie’ are studied here. It was found that the values of η_ie can be expressed as an exponential function of ‘k_h/(-k_v)’ and ‘α’, with a measurable interdependency between ‘α’ and ‘η_ie’. The influence of ‘α’ on the value of ‘η_ie’ increases as the input value of ‘k_h/(-k_v)’ increases. Equations derived based on the analytical results are proposed to account for this effect. Based on the analyses of 11 near-fault seismographers obtained in the 1999 Chi-Chi earthquake in Taiwan, a ratio between the vertical and the horizontal seismic coefficients, λ, of between ±0.25 is suggested for including the combined effect of vertical and horizontal seismic forces in evaluating the seismic bearing capacity of footings located in near-fault areas.

抄録全体を表示

At present, analytical or empirical formula for seismic bearing capacity of footings adjacent to slopes is not available. This study uses a pseudo-static-based approach in conjunction with rigorous Janbu's slice method to derive analytical values of seismic bearing capacity factors (N_γ) and correction factors for the effects of inertia of soil mass and load inclinations for a rigid footing adjacent to cohesionless slopes. It is shown that both the bearing capacity factors (N_γ) and the correction factors for the seismic bearing capacity of footings placed on level ground derived herein are comparable with those reported in the literature. Empirical equations regarding the effects of slope angles and load inclinations, expressed using generalized forms of those proposed in the literature, are also derived. It is also found that the empirical equations derived in the present study provide values of correction factors in good agreements with the analytical ones, indicating the validity of using these empirical equations for assessing the bearing capacity of rigid footings situated on the slope subjected to pseudo-static seismic loading.

抄録全体を表示

Repetitive liquefactions in angular and subangular gravels from an alluvial fan, in the case of two earthquakes with accelerations lower than that of a former which had caused liquefaction some months before, are described. The liquefaction took place from the surface, down to a depth of approximately 10 m. Water laden with sediments spouted out for some tens of minutes after the strong motion ceased. Knowledge of the grain size distribution of the sediments inside the body of the alluvial fan roughly defines the areas of the fan prone to future liquefaction. Non-repetitive liquefaction in overconsolidated fine fluvio-lacustrine sand of glacial origin at the unusual depth of 14 m to 16 m is also described. From the observation of sand lifted up for 10 m inside a large diameter well, and of that which spouted out from several microvents, it was estimated that extra-pore pressure was close to lithostatic conditions. Nevertheless, modeling of intrinsic pore pressure buildup on the DESRA2 programme gives lower values than the experimental one. Geotechnical characteristics of the 12 m-thick sandy stratum indicate that the upper part is unusually soft, either due to water circulation or past repetitive liquefactions which prevented reconsolidation. It is suggested that excess pore pressure generated by the earthquake was also due to redistribution of pressure from adjacent sediments.

抄録全体を表示

 The stability of

‒tetrahydrocannabinol acetate (‒THC‒OAc) and ‒tetrahydrocannabinol acetate (‒THC‒OAc) in -liquid during storage was investigated. ‒THC‒OAc liquids in cartridges were stored at ℃ or 30℃ for 28 days. The relative concentrations of cannabinoids in the liquids were measured by gas chromatography with flame ionization detection. ‒THC‒OAc decreased during storage at either temperature. ‒THC, a minor impurity, also decreased. ‒THC‒OAc liquid in a cartridge was stored at ℃ for 57 days. The concentration of ‒THC‒OAc and ‒THC, a minor impurity, did not change during that time. Cannabinol acetate increased in all liquids, and unknown products were also detected by gas chromatography/mass spectrometry (GC/MS). The ‒THC‒OAc and ‒THC‒OAc liquids were subjected to GC/MS to detect representative diluents, glycerol, propylene glycol, and polyethylene glycol 400, but none of these were detected.

抄録全体を表示

The small strain stiffness and anisotropic nature of two sands with different geological origin have been determined via laboratory seismic tests performed in a triaxial cell. Dry triaxial reconstituted specimens of Ticino river silica sand (TS) and of Kenya carbonatic sand (KS) were subjected to isotropic and anisotropic states of effective stress ; then both shear and constrained compression waves were propagated in vertical, horizontal and oblique directions by means of five couples of piezoelectric transducers especially arranged in the specimens. The propagated compression and shear waves allow the assessment of the constrained M₀ and shear G₀ moduli respectively, at very small strains where, as a first approximation many soils can be assumed, from an engineering point of view, to behave as an elastic cross-anisotropic medium with a vertical axis of symmetry. This paper, after a brief description of the novel measuring technique adopted and of the tested materials, summarises the test results and their interpretation in order to separate the effects of the fabric anisotropy from those produced by the state of effective stresses on soil stiffness. The stiffness and anisotropic response of the two tested sands are compared. Finally the results enable us to establish five independent constants of the cross-anisotropic elasticity model, which appears to be appropriate to reproduce the behaviour at small strain of the two sands.

抄録全体を表示

A procedure for limit equilibrium slope analysis based on a realistic consideration of the mobilized interslice shear forces is presented in this paper. This new approach ensures that solutions are kinematically admissible and the possibility of convergence problems, often associated with numerical solutions, is minimized. The proposed approach recognizes the importance of slip surface geometry in estimating interslice shear forces whether vertical or non-vertical slices are used in a limit equilibrium analysis. Illustrative examples are presented and the results shown to be reasonable. The calculated factors of safety based on the new method compare very well with values based on recognized methods of analysis. Yet the method is more direct and enables a proper visualization of the transfer of mobilized normal and shear forces through a sloping soil mass above a potential slip surface. The method also gives consistent results with non-vertical slices even if the shape of non-vertical slices is varied.

抄録全体を表示

A new analytical method is proposed for determining the inextensible grid reinforcement pullout resistance and pullout force/pullout displacement curve by using basic backfill soil and grid reinforcement properties. The pullout skin friction resistance/pullout displacement relationship is simulated by linear elastic-perfectly plastic model. A hyperbolic model has been proposed to represent the pullout bearing resistance/pullout displacement relationship in which the maximum bearing resistance of a single bearing member is determined using a new bearing capacity equation proposed in this paper. The influences of the grid bearing member spacing ratio, S/D, the bearing member deflection rigidity, and the pullout softening behavior on the mobilization of pullout bearing resistance are explicitly included in the proposed model. Good agreement has been obtained between calculated values and laboratory test results.

抄録全体を表示

 We examined the stability of

-tetrahydrocannabinol acetate (-THC-OAc) and -tetrahydrocannabinol acetate (-THC-OAc) in -liquid products. Eight samples were heated at 30℃ for 28 days and one of them was heated at 70℃ for 2, 4, , 10, and 15 days. Residual ratios of -THC-OAc and -THC-OAc were evaluated by gas chromatography with flame ion detection and their degradation products were examined by gas chromatography/mass spectrometry (GC/MS). Some samples were tested for solubility in hexane and were submitted to GC/MS analysis to detect propylene glycol and glycerol. After a 28-day incubation at 30℃, -THC-OAc was slightly decomposed (residual ratio: 84.–94.2%) but -THC-OAc was almost stable (residual ratio: 95.2–108.%). Heating at 70℃ decomposed not only -THC-OAc but also -THC-OAc. The decomposition proceeded rapidly in the initial 2 days then slowly until 15 days later. The degradation products, four putative one-oxygen-atom adducts and cannabinol, were detected but deacetylated products (-tetrahydrocannabinol and -tetrahydrocannabinol) were not detected. All the samples tested were completely dissolved in hexane differently from propylene glycol and glycerol. Propylene glycol and glycerol were not detected from the samples completely dissolved in hexane. This study indicated that deacetylation of -THC-OAc and -THC-OAc did not proceed when the sample did not contain propylene glycol and glycerol.

抄録全体を表示

In this paper, instead of the time-invariant state-space representation in the consequent of the T-S fuzzy model, tim,-varying system is considered in order to deal with the reconstruction error between the real system to be controlled and its T-S model, and fuzzy approximator is employed to cope with unknown functions involved in the model. As a result, it reaches an adaptive controller that has two parts: one is obtained by solving certain linear matrix inequalities (LMIs) (fixed part) and another one is acquired by the fuzzy approximator in which the related parameters are tuned by adaptive law (variable part). The proposed controller can guarantee the closed-loop system to be asymptotically stable.

抄録全体を表示

Walking rehabilitation machines have drawn great attentions with more and more people suffering from walking disabilities in an aging society. However, most of the developed walking rehabilitation machines aim at enhancing muscle strength, neglecting the recovery of the neural system. 58% of walking disabilities are caused by problems in the neural system. Therefore, we propose a rehabilitation system which includes both muscle strength enhancement by a walking rehabilitation machine and neurological rehabilitation by imaginary walking. In this paper we compared the activation in motor area of the brain during real walking and imaginary walking by means of fNIRS (functional Near-InfraRed Spectroscopy). Two subjects participated in the experiment. During imaginary walking, the subjects were instructed to imagine that they were walking with the same pace to a person in the video being shown to the subjects. As a result, the concentration of oxygenated hemoglobin in motor area during imaginary walking was higher than that during real walking in both of the subjects. This was because that it was not necessary to pay attention to the movements of the legs and feet during normal walking on the plain road without any obstacles, while movement planning was required when the subjects imagined their walking in the same way to another person. The experiment result indicated that it is possible to quicken walking rehabilitation by imaginary walking.

抄録全体を表示

This paper presents the results of 24 centrifuge model tests of nailed soil slopes and vertical walls, constructed out of dry Leighton buzzard sand. The walls were initially supported by fluid pressure from flexible rubber bags against the face, and excavation was modelled by gradually draining the fluid from the bags. The finished model walls were 200 mm high and were initially tested at 30 g acceleration to correspond to a prototype structure .0 m high. If failure was not obtained, the acceleration was increased progressively to a maximum of g. No surcharges were applied. The main parameters varied in the tests were the wall slope, nail length, nail surface roughness, nail inclination, facing stiffness and facing roughness. Observations were made of the mechanism of failure when it occurred, of soil pressures on the facing, and of pre-failure deformations. Failure was always by pull-out rather than breakage of the nails, and a series of pull-out tests of the model nails was conducted to aid interpretation of the results. Failure surfaces were seen to have the shape of logarithmic spirals, and limit equilibrium analyses based on these surfaces agreed well with experimental observations. Prior to failure, earth pressures on the facing compared reasonably well with those calculated by Coulomb's method, except at the base of the wall. One test set out to model a full-scale trial wall, and although the construction process could not be exactly modelled in the small-scale centrifuge tests, comparisons were sufficiently good to give confidence in the model test results.

抄録全体を表示

This paper deals with the overall stability of an embankment foundation failure that lies at km 40+700 of the new Irbid-Amman Highway in Jordan. Slope stability back analysis was carried out for the slope to assess the conditions at time of failure, and estimate most representative shear strength parameters of foundation materials. Slope stability analysis was also carried out for proposed remedies. Probabilistic seismic hazard analysis was carried out for the landslide site. Peak Ground Acceleration (PGA) value of 0.2 g was estimated for design. This corresponds to a % probability of non-exceedence in a 50 year design life of the highway. Pseudo-static slope stability analysis was also carried out. The study concluded that the landslide movement occurred within the foundation colluvium material. It resulted primarily from the excessive load of the embankment and excess piezometric pressures generated within the slope. The most feasible remedial measure to stabilize the landslide area was removal of existing failed embankment down to the top of sandstone layer, and reconstruction (using imported free-drainage rockfill) of a split level embankment together with the construction of surface and subsurface drainage system. These measures were successfully implemented in the field.

抄録全体を表示

To remove some weak points of the limit equilibrium slope stability method, the authors have tried so far to develop a hybrid slope stability analysis method, in which stress and strain developed in a slope are determined by the finite element method, while the basic concept of the limit equilibrium method is adopted in the overall stability analysis. In this paper, first, the theory behind the hybrid slope stability analysis method is presented, together with the comparison of the proposed hybrid method and the conventional Bishop's method. Then, reinforcement mechanism and stability characteristics of the reinforced slope cutting are examined through numerical examples by the proposed method. Finally, practical application of the proposed method to an in-situ reinforcement slope stabilization project is presented. In consequence, the applicability and simplicity of the proposed method to the practical design works of reinforcement slope stabilization are demonstrated in success.

抄録全体を表示

Circuit techniques to enhance the linearity of input-voltage-to-current (V/I) conversion and to increase the output impedance of a current source by compensating for the low intrinsic gain of a transistor were introduced to realize a high-frequency operational transconductance amplifier (OTA) for a low supply voltage using sub-100-nm CMOS processes. Applying these techniques, a MOS 7th-order Gm-C linear-phase low-pass filter (LPF) was realized using a 65nm CMOS process. A simplified biquad LPF that can serve as a component of a 7th-order LPF was newly developed by replacing OTAs with resistors. As a result, the -3dB frequency bandwidth, group delay ripple, 3rd-order distortion, and 3rd-order input intercept point (IIP3) were 200MHz, 2.2%, ≤ -55dB with a 100MHz input, and +10.3dBm, respectively, all with a ±0.Vp-p input signal at each input terminal in the pseudodifferential configuration. The LPF including an output buffer dissipated 60mW in the case of a .2V supply. Wide spurious-free dynamic range (SFDR) characteristics were confirmed up to high frequencies.

抄録全体を表示

One method currently being considered for the disposal of high level radio-active waste is burial in the seabed. When a hot object is buried in soil, the temperature of the soil adjacent to the object is raised and there is transient heat flow away from the object. The rise in the temperature of the soil causes excess pore pressures to be generated and transient pore water diffusion also takes place. A finite element formulation of the coupled heat flow and consolidation problem is presented. The computer implementation of this formulation is found to compare favourably with analytical solutions based on the same physical principles.

抄録全体を表示