In view of the significant role of the water film effect in flow failure for a liquefied sandy deposit, the mechanism of water film generation is numerically studied based on a 1-dimensional model test. The process of water film growth and decay can be simulated to a certain extent by a simple consolidation analysis, which indicates that only a small difference in permeability in layered sand is enough for a water film to develop. A 1 G shaking table test for a two-dimensional slope model with an arc of silt within a saturated sand is then addressed to discuss the dilatancy effect exerted in sheared sand during flow failure. It is possible that, once the water film is formed, the transmission of shear stress through it is interrupted, leaving the sand below free from the dilatancy ; this eventually allows the water film to stay without being absorbed during flow failure. The result of another shaking table test for a trapezoidal slope with horizontal silt seams indicate that water films beneath the seams enable the soil mass above them to laterally flow along water films very gently inclined even after shaking. If a silt seam breaks due to excessive pressure in the water film, it triggers re-liquefaction in the upper sand and leads to further instability.

抄録全体を表示

The behavior of the soft clay grounds subjected to repeated loading is different from that subjected to sustained loading. The difference in settlement between these two loading patterns should be due to secondary compression over a long period of time. Consequently, soft clay grounds subjected to repeated loading tend to be more compressible than those subjected to sustained loading. Therefore, it is necessary for engineers to predict post-construction settlements under repeated loading. In this respect, the preloading is considered to be promising as a countermeasure to reduce the settlement of clay under repeated loading as well as under sustained loading. The effect of preloading on post-construction consolidation settlement of soft clay subjected to repeated loading after removal of a part of preload is investigated in the present paper. It has become clear that the settlement of a clay sample after preconsolidation is mainly affected by the amount of preload, the degree of consolidation due to the preload, the amount of permanent load and the amount of repeated load after removal of preload. The calculated settlement versus time relations using a method to estimate the amount of consolidation settlement of soft clay grounds subjected to repeated loading after removal of preloading were compared with the observed degree of consolidation as parameters of the intensities of preload and repeated load.

抄録全体を表示

An empirical equation in use for estimating the pseudo-elastic shear modulus, G_f, of subsoil, associated with shear strains less than 0.001% is proposed in this paper. In a series of in-situ seismic cone tests performed nationwide, the profiles of both G_f and the in-situ void ratio, , with depth were successfully characterised at five sites, each comprising a soft clay layer deposited in the Holocene era. The database which comprised the original data from the field and laboratory tests, coupled with similar information on well-documented Holocene clay deposits in Europe, was statistically analyzed in attempts to determine a generalised relationship with which G_f of soft clay may be reasonably estimated only from routinely available borehole data; that is and the current geostatic effective overburden pressure, σ'_v. An empirical relationship, G_f=, 000 -√(σ'_v) (kPa), was derived from the statistical analysis applied to data from seven different clays worldwide, for which extended over a range between 1 and , and the overconsolidation ratio ranged roughly between 1 and 2. The applicability of the proposed relationship was evaluated for two case records, each in which the clay exhibited unusual behavior; i.., the undrained shear strength remained more or less constant with depth due to the existence of artesian pressure at one site, and, at the other, G_f decreased, whereas increased, with depth. It was demonstrated that even in these clay deposits exhibiting exceptional profiles, the proposed relationship was capable of predicting G_f with a reasonable accuracy by determining the profiles of and σ'_v with depth. In addition, the prediction when compared to G_max from carefully performed laboratory cyclic tests, yielded a better estimate of G_f from the in-situ seismic survey. Despite the fact that the empirical relationship was initially designated to estimate G_f of soft clays, it may be equally applicable to sandy deposits. This was verified by comparing it to similar, and well-established, relationships developed for sands. A case record as such is also described for a loose sand deposit at Higashi-Ohgishima in Tokyo Bay which was placed in 1960's by land reclamation.

抄録全体を表示

In this paper, consideration is given as to how to characterize depth-variation for the small-strain shear modulus of natural clay sedimentation, in a state of normal consolidation. A case study was carried out for a relatively uniform clay layer deposited in the Holocene era. Initially, the effects of both strain and in-situ stress levels on secant shear modulus were carefully examined in cyclic torsion shear tests using undisturbed samples, which were recovered at different depths in a test borehole. The range of shear strain examined was between 0.001% and 1%. Similar examination was made for a silty clay using reconstituted samples that were isotropically consolidated at different stress levels. On the basis of the results of these laboratory tests, together with the shear modulus from an in-situ seismic survey, the small-strain shear modulus was formulated in terms of the stress and strain levels, and linked also to undrained shear strength. Interactions of the small strain stiffness between in-situ and laboratory are discussed in depth with an attention paid to the existing aging effect in the original subsurface condition.

抄録全体を表示

In the 1993 Kushiro-oki Earthquake of Richter magnitude ., simultaneous recording of earthquake motions was successfully made at the ground surface and at a depth of 77 meters in a dense saturated sand deposit. The peak horizontal acceleration was 0.47 g on the ground surface and 0.21 g at a depth of 77 meters. The acceleration record at the ground surface showed a distinctive ground response, which consisted of a cyclic motion having a period of about 1. seconds overlain by a spike at each peak of the motion. In order to study the mechanism of this peculiar ground response, effective stress analysis was conducted on the dense saturated sand deposit. The model used for this study was a strain space multiple mechanism model, which takes into account the effect of principal stress axis rotation. The recorded earthquake motion at a depth of 77 meters was used as the input earthquake motion for the analysis. Sampling after in-situ freezing was done in order to evaluate the properties of the sand. The results of the analysis indicated that the observed ground response was due to the effect of dilatancy of sand, which plays a significant role in the response of the dense saturated sand deposits during strong earthquake motions.

抄録全体を表示

Stress wave theory is applied to open-ended pipe piles to clarify the effects of soil plug on the behaviour of piles during driving and static loading. Measured field data and various numerical models are reviewed ; methods are presented to calculate wave propagation in both the pile and the soil plug ; modelling is presented which takes into account the interaction between the soil plug and the pile ; also presented is simplified method to estimate the loadsettlement relation of the pipe pile in static loading. By correlating observed and calculated values in two analytical cases, the authors demonstrate that incorporation of the soil plug (modelled as a series of masses and springs) is required to correctly predict pile behaviour during driving and static loading.

抄録全体を表示

In this paper, centrifuge shaking table tests were conducted in order to understand the performance of seawalls during a seismic event. The model tests showed that the displacement of the caisson was much affected by the seaward shear deformation of the sand seabed beneath it during shaking. It was also confirmed that an armored embankment played an important role in the displacement of the caisson during shaking. Based on these test results, a two-dimensional DEM-FEM coupled analysis method was newly developed to numerically predict the deformation of seawalls covered with armored embankments during earthquakes. The movements of the armor units were calculated by DE analysis and deformations of the caisson, rubble mound, sand seabed and backfill were calculated by FE analysis considering the non-linearity of the soil materials based on the effective stress. Dynamic interaction was taken into account by delivering the nodal displacements of the finite elements or the nodal forces converted from the contact forces through the imaginary distinct elements defined at the boundaries between the DE and FE domain. The applicability of this method to the prediction of the deformation of seawalls was verified through numerical simulations of the centrifuge model test.

抄録全体を表示

Seismic records obtained from a seismometer array located in downtown Tokyo Japan for about ten years were inversely analyzed to estimate the dynamic soil parameters. Due to the illposed nature of the problem, the simple and often used "least square method" does not properly estimate the parameters. The Extended Bayesian Method combined with the Akaike Bayesian Information Criterion was introduced to overcome this difficulty. The results obtained were compared with dynamic triaxial test results obtained at the time of the seismometer installation. The shear moduli agree quite well with the estimated results, however the damping ratios estimated are slightly higher than the ones obtained in the laboratory.

抄録全体を表示

The ability of Climacodon septentrionalis to immobilize and kill a mycophagous nematode (Aphelenchoides sp.) in vitro is described for the first time. Two isolates produced droplets (20–45 μm in diameter) that formed at the apices of tall, stalked, and branching secretory cells (700–1,500 μm tall). On 2% modified malt extract agar, nematodes became enveloped in the droplets, which restricted their ability to move and resulted in complete immobilization and death within several hours of contact. The rate of decomposition of the nematodes varied considerably, with most individuals persisting for weeks whereas others were degraded within several days and appeared to be colonized by dense hyphal growth. This study provides the first documentation of a non-agaricoid fungus producing secretory cells that are able to immobilize nematodes.

抄録全体を表示

Among the rivers damaged by the earthquake, two most severely damaged along the Yodo-gawa River are described. In the left levee, the settlement exceeded 2 m for a length of 1. km, with a maximum settlement of 3 m. Sand boils were observed extensively on the ground surface near the damaged dikes. Holocene sandy soil with an SPT N-value of 10 or less existed in the upper part of the subsoil profile. These facts indicate that liquefaction of the soil was the major cause of the embankment damage. The cyclic stress ratio required to cause liquefaction was 0.30 as determined from cyclic triaxial tests on undisturbed samples.

抄録全体を表示

Field data indicate that the P-wave velocity in sand or gravel is sometimes much lower than that of water, even if the soil is below the water table. It is well understood that a slight decrease in saturation normally evaluated by the -value has a significant effect on undrained shear behavior like liquefaction of saturated soil. In the first part of this research, theoretical formulations of the -value, P-wave velocity and Poisson's ratio are made by taking into account the decrease in bulk modulus of water due to a mixture of air bubbles. Then, computations are carried out using formulas based on the soil properties of a typical sand or gravelly soils and Masa soil from the Kobe area to make charts correlating the variables. These charts indicate that a small decrement in the -value in the interval of =1.0 to 0. will considerably decrease the P-wave velocity. Thus, the P-wave velocity which is easily measured in the field can serve as a convenient index to quantitatively evaluate the insitu soil -value.

抄録全体を表示

The mechanism of wave-induced instability in a permeable seabed have been studied for more than two decades. The distinction between shear failure and liquefaction, however, has not been clearly defined. This paper presents a fundamental study on the differences in two failure modes for a fully saturated seabed of both finite and infinite thickness. The wave-induced effective stresses and pore pressure, obtained from an analytical solution of Biot's pore-elastic consolidation theory, were employed to examine the failure modes under a two-dimensional plane strain condition. A case study is presented to examine the failure modes with respect to several parameters, such as excess pore pressure, seepage flow, seepage force, failure areas and stress path in the seabed. The conclusions obtained from this study were as follows ; (1) the thickness of a permeable seabed affects the pore pressure and effective stress response to ocean waves and the failure mode of the seabed, (2) either a liquefaction or shear failure, or both, occur in the seabed, even in the saturated seabed, (3) the Mohr-Coulomb's failure criterion, when combined with elastic stresses, can not be employed to estimate the liquefaction failure in the seabed, () the liquefaction can be evaluated by a criterion in terms of the excess pore pressure, () The liquefied zone in the seabed is significantly different from the shear failure zone. The shape beneath the seabed surface for the former is almost identical to the contour where the upward seepage flow is concentrated.

抄録全体を表示

Based on the methods previously presented by the authors (Yasuhara et al., 1992, 1994, 1996) for predicting the degradation in strength and stiffness of soft clays in the course of cyclic loading, a methodology has been developed to estimate the cyclic loading-induced settlements. The method also includes not only immediate settlements but also post-cyclic long-term settlements due to dissipation of cyclically induced excess pore pressures in soft soils. The simplified formulae included in the proposed methodology are given as functions of the amplitude of cyclic-induced excess pore pressure normalized by the confining pressure, u/p'_c, plasticity index I_p and factor of safety against bearing capacity failure, F_s. The calculations of cyclic-induced settlements were conducted for soft soil deposits with different index and geotechnical properties. The results calculated using the proposed methodology are presented in the form of a design chart to give the settlement versus normalized excess pore pressure ratio relations including the effects of the plasticity index and safety factor for bearing capacity. An example of the calculated results using the proposed procedure for the earthquake-induced settlements of embankments founded on soft clay, is presented to demonstrate the practicality of the method for design at fields.

抄録全体を表示

Shaking table tests were performed to clarify the settlement in liquefied loose sand of a new foundation incorporating top-shaped concrete blocks. In the tests, blocks of half scale were installed as they are in practice, by using a crusher-run, a lattice of iron rods and iron bars. Shaking table tests were also conducted on foundations with two differently shaped concrete blocks to investigate the effectiveness of the three foundations in reducing settlement. One was a T-shaped concrete block, or a disk-shaped concrete plate with a leg. The other was a conical concrete block without a leg. The results of shaking table tests showed that the foundation with the top-shaped concrete blocks was most effective in reducing the settlement among the three types of foundation. FEM elastic analyses were performed to compute the stress distributions in the models and in-situ ground when the top-shaped concrete blocks were applied and to confirm whether liquefaction resistance of the sand layer below the foundation is large. Moreover, the factor of safety against liquefaction, F_L was evaluated in in-situ model ground, in order to compare with sensitivities against liquefaction in the ground without countermeasures and with top-shaped concrete blocks. For the liquefaction analyses, shear stress in the ground during an earthquake was estimated by dynamic analyses using the SHAKE computer program.

抄録全体を表示

The original Drnevich Resonant Column apparatus has been designed for testing cylindrical soil specimen with maximum longitudinal and torsional stiffnesses corresponding to approximate resonant frequencies 285 Hz and 318 Hz respectively. This apparatus has been modified successfully and its stiffness has been increased to over threefold in the longitudinal vibratory mode and at least twofold in the torsional vibratory mode. Monterey No. O sand samples prepared at approximate relative densities 43% and 60% were tested with the original and the modified apparatus in the range of effective confining pressures from 49 kPa to 588 kPa. Measurement of dynamic moduli values measured with the original apparatus were up to 23% higher, and damping values up to five times higher than those measured by the modified apparatus.

抄録全体を表示

Natural sedimentary clays exhibit ageing effects on their behaviour when subjected to both consolidation and shearing. Attempts to characterising the in-situ 'structure'of soft marine clays have been made in case studies performed in Ariake (Japan) and in Bangkok (Thailand), each showing a typical profile of aged clay-structure with depth reflecting its site-specific geological consolidation history. In each site, profiles of Atterberg limits, natural water content, overconsolidation ratio (OCR), quasi-elastic shear modulus G_max and the undrained shear strength c_u with depth were attained from various laboratory tests, together with the a comparable profile of quasi-elastic shear modulus from insitu seismic survey G_f. Quantitative assessment of the aged clay-structure was made by using two different measures, metastability index MI (G) and the soil constant reflecting structure S (Jamiolkowski et al., 1994). The profiles of MI (G) and the S-value with depth were both determined based on the corresponding G_max behaviour of the reconstituted sample. "Disturbance"of laboratory samples retrieved by using two different samplers (i.., Laval and Japanese thin-walled samplers) with two different sampling techniques (i.., pre-boring and displacement methods) was discussed. A new approach to estimate c_u"in the ground", termed by the authors the MILK (Metastability Index coupled with Laboratory K_o test) method, is proposed. A trial of the MILK-method is demonstrated in soft Bangkok clay, the texture of which is similar to "soft cheese".

抄録全体を表示

An earthquake of magnitude . occurred in the south-east coast of El Salvador on January 13, 2001, causing widespread damage to buildings and several kinds of civil engineering structures due to ground shaking and earthquake-induced ground failures, including several large-scale landslides. This paper discusses the results of the damage investigation conducted in the area after the earthquake, with emphasis on the general features of the earthquake and its effects on the ground damage, specifically the landsliding which occurred in natural slopes and the liquefaction of soil deposits. The occurrence of liquefaction in the alluvial plain exhibited several characteristics in common with those observed in other areas of similar condition. On the other hand, the main cause of slope failures in volcanic deposits was not clearly identified, and several possible sources of slope instability were pointed out.

抄録全体を表示

This text is concerned with the basic principles underlying current practice in the earthquake response analysis of soft alluvial deposits. Its special interest is focused on the stratification of alluvium that has been modeled in analyses by layers in which soil properties are uniform. Since the age and the effective stress are continuous in the vertical direction, it is possible that the soil-dynamic properties such as shear modulus and damping ratio are not uniform but varying continuously in the vertical direction. From this viewpoint, the conventional idea of uniform layers was examined in detail by conducting detailed investigations in-situ, as well as laboratory tests on continuously collected undisturbed soil samples. The test results show that soil properties continuously vary in the vertical direction within an alluvium. This holds true even when the soil type changes from clayey to sandy. In contrast, a discontinuity of properties was detected at an unconformity of Pleistocene layers where the age and sedimentation process are discontinuous. With this knowledge, an attempt was made to propose a recommendable modelling of soil stratification for practical earthquake response analysis on alluvium.

抄録全体を表示

The Split Hopkinson Pressure Bar method (S. H. P. ) provides a ready means for direct analysis of material dynamic response. Soil Specimens generally present poor mechanical properties, thus the classical experimental device has to be adapted. An original experimental arrangement "Three-Dimensional Split Hopkinson Pressure Bar" (3-SHPB) is proposed. It allows measurement of the complete three-dimensional dynamic response of soils. Experiments are oedometric type tests (rigid confining cylinder) involving dynamic radial stress measurement. Pseudo Poisson's ratio is then determined and the influence of strain rate is shown. In addition, other types of confining systems are used : soft and semi-rigid confinement and low impedance tests are performed. Results on different loading paths are compared with others on sands and clays. Analysis at grain-size level gives further elements on the comminution process.

抄録全体を表示

The paper focuses on the development and modelling of residual cyclic pore water pressure, u, in clay during undrained cyclic strain-controlled loading. Data obtained from a series of NGI type cyclic simple shear tests were employed. In addition to the amplitude of cyclic shear strain, γ_c, the number of cycles, N, and the overconsolidation ratio, OCR, a new component is incorporated in the conventional characterization of u. This new component is the volumetric threshold shear strain, γ_tv, of clayey soils, below which for all practical purposes u does not develop. The lack of understanding of complex clay microstructure and the associated interaction between clay particles during cyclic shearing makes the modelling of u in a manner other than curve fitting rather difficult. This is especially true in regard to the development of negative u in overconsolidated clays. A model based on the systematic curve fitting of the pore pressure data expressed in terms of γ_c, γ_tv, N and OCR is presented. The possibilities of the incorporation of such a model into existing numerical tools for simulation of the seismic and ocean wave loading response of natural soil deposits are briefly discussed as well.

抄録全体を表示