Repetitive liquefactions in angular and subangular gravels from an alluvial fan, in the case of two earthquakes with accelerations lower than that of a former which had caused liquefaction some months before, are described. The liquefaction took place from the surface, down to a depth of approximately 10 m. Water laden with sediments spouted out for some tens of minutes after the strong motion ceased. Knowledge of the grain size distribution of the sediments inside the body of the alluvial fan roughly defines the areas of the fan prone to future liquefaction. Non-repetitive liquefaction in overconsolidated fine fluvio-lacustrine sand of glacial origin at the unusual depth of 14 m to 16 m is also described. From the observation of sand lifted up for 10 m inside a large diameter well, and of that which spouted out from several microvents, it was estimated that extra-pore pressure was close to lithostatic conditions. Nevertheless, modeling of intrinsic pore pressure buildup on the DESRA2 programme gives lower values than the experimental one. Geotechnical characteristics of the 12 m-thick sandy stratum indicate that the upper part is unusually soft, either due to water circulation or past repetitive liquefactions which prevented reconsolidation. It is suggested that excess pore pressure generated by the earthquake was also due to redistribution of pressure from adjacent sediments.

抄録全体を表示

A new analytical method is proposed for determining the inextensible grid reinforcement pullout resistance and pullout force/pullout displacement curve by using basic backfill soil and grid reinforcement properties. The pullout skin friction resistance/pullout displacement relationship is simulated by linear elastic-perfectly plastic model. A hyperbolic model has been proposed to represent the pullout bearing resistance/pullout displacement relationship in which the maximum bearing resistance of a single bearing member is determined using a new bearing capacity equation proposed in this paper. The influences of the grid bearing member spacing ratio, S/, the bearing member deflection rigidity, and the pullout softening behavior on the mobilization of pullout bearing resistance are explicitly included in the proposed model. Good agreement has been obtained between calculated values and laboratory test results.

抄録全体を表示

The Beckmann rearrangement of aliphatic ketone oximes, R(CHs)=NOH (R=Et (1); n-Pr (2); iso-Pr (3); iso-Bu (4)), with polyphosphoric acid (PPA), polyphosphate ester (PPE), and ester of phosphoric acid (2 P- R) was carried out and migratory ratios ((a)/(b) in eq. (1)) were determined, The results are shown in Fig.1, 2, and 3, respectively.
In Fig.1 and 2, the migratory ratios decrease with reaction time and nearly approach to the ratios of anti-alkyl form/syn-alkylform in benzene(A1) or DMSO(A2)except for (3) (See Table 1). From this fact, it has been found that PPA and PPE are inactive for isomerization of the oximes andanti-alkyl oximes rearrange faster than syn-alkyl ones. ln the case of (3), migratery ratios are smaller than Ai or A2. As acetonitrile is detected by GLC, it is presumed that fission has been occurred simultaneously with rearrangement in anti-alkyl oxime (eq. (3)). In the case of 2 P- R, all modes of the reaction arethe same as in above, except that the rate of fission is tnuch faster than that in PPA and PPE.
The reaction of anti-alkyl ketone oximes having a bulky grouphas been greatly influenced by the use of sterically demanding catalysts such asPPA, PPE, and 2 P- R.

抄録全体を表示

 The stability of

‒tetrahydrocannabinol acetate (‒THC‒OAc) and ‒tetrahydrocannabinol acetate (‒THC‒OAc) in -liquid during storage was investigated. ‒THC‒OAc liquids in cartridges were stored at 80℃ or 30℃ for 28 days. The relative concentrations of cannabinoids in the liquids were measured by gas chromatography with flame ionization detection. ‒THC‒OAc decreased during storage at either temperature. ‒THC, a minor impurity, also decreased. ‒THC‒OAc liquid in a cartridge was stored at 80℃ for 57 days. The concentration of ‒THC‒OAc and ‒THC, a minor impurity, did not change during that time. Cannabinol acetate increased in all liquids, and unknown products were also detected by gas chromatography/mass spectrometry (GC/MS). The ‒THC‒OAc and ‒THC‒OAc liquids were subjected to GC/MS to detect representative diluents, glycerol, propylene glycol, and polyethylene glycol 400, but none of these were detected.

抄録全体を表示

This paper outlines a mathematical description of the stress dilatancy behaviour of granular materials which accounts for stress level and void ratio dependencies. The consideration of these aspects has important implications in the modelling of granular material behaviour. In fact, granular material mechanical response is largely dominated by the evolution of dilatancy, fabric and void ratio histories. The starting point in this study is the well established Rowe's theory which is revisited and ultimately modified by introducing a factor linked to governing state parameters in order to describe the complete behaviour of granular materials during deformation. Numerical simulations of triaxial tests on granular materials at different void ratios and stress levels are herein presented to illustrate the model.

抄録全体を表示

The correction factor (η_ie) for the ultimate bearing capacity of a footing placed adjacent to a slope, taking into account the combined effect of horizontal and vertical seismic loads, represented by horizontal and vertical seismic coefficients, k_h and k_v, respectively, was derived using a modified Janbu's slice method. The influence of slope angles ‘α’ on the values of ‘η_ie’ are studied here. It was found that the values of η_ie can be expressed as an exponential function of ‘k_h/(1-k_v)’ and ‘α’, with a measurable interdependency between ‘α’ and ‘η_ie’. The influence of ‘α’ on the value of ‘η_ie’ increases as the input value of ‘k_h/(1-k_v)’ increases. Equations derived based on the analytical results are proposed to account for this effect. Based on the analyses of 11 near-fault seismographers obtained in the 1999 Chi-Chi earthquake in Taiwan, a ratio between the vertical and the horizontal seismic coefficients, λ, of between ±0.25 is suggested for including the combined effect of vertical and horizontal seismic forces in evaluating the seismic bearing capacity of footings located in near-fault areas.

抄録全体を表示

At present, analytical or empirical formula for seismic bearing capacity of footings adjacent to slopes is not available. This study uses a pseudo-static-based approach in conjunction with rigorous Janbu's slice method to derive analytical values of seismic bearing capacity factors (N_γ) and correction factors for the effects of inertia of soil mass and load inclinations for a rigid footing adjacent to cohesionless slopes. It is shown that both the bearing capacity factors (N_γ) and the correction factors for the seismic bearing capacity of footings placed on level ground derived herein are comparable with those reported in the literature. Empirical equations regarding the effects of slope angles and load inclinations, expressed using generalized forms of those proposed in the literature, are also derived. It is also found that the empirical equations derived in the present study provide values of correction factors in good agreements with the analytical ones, indicating the validity of using these empirical equations for assessing the bearing capacity of rigid footings situated on the slope subjected to pseudo-static seismic loading.

抄録全体を表示

The main objective of this paper is to compare safety factors obtained from Morgenstern-Price, Janbu and Spencer methods with the factors calculated from the modified variational approach (Leshchinsky and Huang, 1992a). Such comparison is essential since there is no mathematical proof that the variational analysis indeed yields a minimum and thus, physically produce significant results. The safety factors compared well, indicating the variational analysis is on a par with acceptable existing rigorous methods. Availability of a user-friendly computer code may make the variational analysis useful to practicing engineers. However, its greatest potential at the moment is in 3- applications; i.., unlike other methods, its extension to 3- is straightforward.

抄録全体を表示

By employing an undrained cyclic loading ring-shear apparatus, a series of tests to reproduce the dynamic behavior of the Nikawa landslide induced by the January 17, 1995 Hyogoken-Nambu earthquake, is conducted. The test sample is Osaka-group coarse sandy soil taken from the landslide. The initial stress condition acting on a soil element in the sliding surface is applied to the sample. Based on the seismic records monitored at the JR Takarazuka Station, the input seismic wave is synthesized to reproduce the seismic stress acting on the sliding surface. The test results show that the soil failed due to the dynamic loading of the earthquake. The most important results are the excess pore water pressure generation and the acceleration of shear displacement continuing after the main shock. Combined with the grain crushing at the shear zone and the volume reduction in the drained constant-speed ring-shear test, the mechanism of this landslide is interpreted as, shear displacement causing grain crushing in the shear zone and volume reduction, and then resulting in a localized liquefaction phenomenon, "sliding-surface liquefaction". This geotechnical simulation test provides a reasonable interpretation of this highly mobile landslide.

抄録全体を表示

Two new partially saturated tricyclic ring systems, , a, 7, , , 10, 10a, 11-octahydro-11-oxodibenz [b, ] oxepins (3a and 3b), and -thiepins (4a and 4b) were synthesized. Compounds 4a and 4b were desulfurized to give a pair of isomeric 2-methylbenzoylcyclohexanes (10a and 10b). Deuterated 4a and 4b (11a and 11b) were prepared starting from butadiene- (12). The stereochemical features of 3a (trans), 3b (cis), 4a (trans) and 4b (cis) are compared with those of 10a, 10b, 11a and 11b on the basis of proton nuclear magnetic resonance data.

抄録全体を表示

In this study the field feasibility of an innovative thermal technique to improve the performance of prefabricated vertical drains (PVD) used in conjunction with the preloading ground improvement method is investigated. For this purpose, two identical .0 m high full-scale test embankments for preloading were constructed over the soft Bangkok clay where a conventional PVD system was installed underneath one embankment and a novel prefabricated vertical thermo-drain (PVTD) system was utilized for the other. The PVTD unit consists of a U-tube made of cross-linked polyethylene plastic (PEX) that is attached to a conventional PVD unit. Preheated water at about 90° is circulated through the attached U-tube to raise the soil temperature underneath the PVTD embankment. The behavior of the two test embankments were compared in terms of excess pore water pressure and consolidation results. The comparison shows the advantage of a PVTD system over a conventional PVD system. The rate of consolidation increases significantly in the PVTD system due to the temperature effect on the hydraulic conductivity. Moreover, the embankment with the PVTD system generates more settlement due to the thermally induced irreversible contraction of saturated normally consolidated soft Bangkok clay.

抄録全体を表示

Circuit techniques to enhance the linearity of input-voltage-to-current (V/I) conversion and to increase the output impedance of a current source by compensating for the low intrinsic gain of a transistor were introduced to realize a high-frequency operational transconductance amplifier (OTA) for a low supply voltage using sub-100-nm CMOS processes. Applying these techniques, a MOS 7th-order Gm- linear-phase low-pass filter (LPF) was realized using a 65nm CMOS process. A simplified biquad LPF that can serve as a component of a 7th-order LPF was newly developed by replacing OTAs with resistors. As a result, the -3dB frequency bandwidth, group delay ripple, 3rd-order distortion, and 3rd-order input intercept point (IIP3) were 200MHz, 2.2%, ≤ -55dB with a 100MHz input, and +10.3dBm, respectively, all with a ±0.1Vp-p input signal at each input terminal in the pseudodifferential configuration. The LPF including an output buffer dissipated 60mW in the case of a 1.2V supply. Wide spurious-free dynamic range (SFDR) characteristics were confirmed up to high frequencies.

抄録全体を表示

 We examined the stability of

-tetrahydrocannabinol acetate (-THC-OAc) and -tetrahydrocannabinol acetate (-THC-OAc) in -liquid products. Eight samples were heated at 30℃ for 28 days and one of them was heated at 70℃ for 2, 4, , 10, and 15 days. Residual ratios of -THC-OAc and -THC-OAc were evaluated by gas chromatography with flame ion detection and their degradation products were examined by gas chromatography/mass spectrometry (GC/MS). Some samples were tested for solubility in hexane and were submitted to GC/MS analysis to detect propylene glycol and glycerol. After a 28-day incubation at 30℃, -THC-OAc was slightly decomposed (residual ratio: 84.–.2%) but -THC-OAc was almost stable (residual ratio: 95.2–108.%). Heating at 70℃ decomposed not only -THC-OAc but also -THC-OAc. The decomposition proceeded rapidly in the initial 2 days then slowly until 15 days later. The degradation products, four putative one-oxygen-atom adducts and cannabinol, were detected but deacetylated products (-tetrahydrocannabinol and -tetrahydrocannabinol) were not detected. All the samples tested were completely dissolved in hexane differently from propylene glycol and glycerol. Propylene glycol and glycerol were not detected from the samples completely dissolved in hexane. This study indicated that deacetylation of -THC-OAc and -THC-OAc did not proceed when the sample did not contain propylene glycol and glycerol.

抄録全体を表示

11-Amino-, a, 7, , , 10, 10a, 11-octahydrodibebenzo[b, ]thiepines (a-) and -oxepines (7a-) were synthesized by the Leuckart reaction of , a, 7, , , 10, 10a, 11-octahydro-11-oxodibenzo[b, ]thiepines (1a, b)and -oxepines (2a, b) followed by hydrolysis of the reaction products 4a- and a-, respectively. The four diastereomers, cis(a-H, 10a-H)-cis(10a-H, 11-H) a and 7a, cis(a-H, 10a-H)-trans(10a-H, 11-H) b and 7b, trans(a-H, 10a-H)-trans(10a-H, 11a-H) and 7, and trans(a-H, 10a-H)-cis(10a-H, 11-H) and 7, were isolated and their configurations and conformations were elucidated by chemical methods together with ¹H-nuclear magnetic resonance spectroscopic and X-ray crystallographic analyses.

抄録全体を表示

A procedure for limit equilibrium slope analysis based on a realistic consideration of the mobilized interslice shear forces is presented in this paper. This new approach ensures that solutions are kinematically admissible and the possibility of convergence problems, often associated with numerical solutions, is minimized. The proposed approach recognizes the importance of slip surface geometry in estimating interslice shear forces whether vertical or non-vertical slices are used in a limit equilibrium analysis. Illustrative examples are presented and the results shown to be reasonable. The calculated factors of safety based on the new method compare very well with values based on recognized methods of analysis. Yet the method is more direct and enables a proper visualization of the transfer of mobilized normal and shear forces through a sloping soil mass above a potential slip surface. The method also gives consistent results with non-vertical slices even if the shape of non-vertical slices is varied.

抄録全体を表示

The advantages and disadvantages of using a back analysis of slope failures to evaluate soil shear strength are discussed. A methodology is presented herein that allows the implied level of reliability associated with soil shear strength parameters back calculated from slope failures to be estimated. A reliability approach is also used to estimate the probability of failure for a given limit equilibrium slope stability method, design factor of safety, and combination of back calculated Mohr-Coulomb shear strength parameters, ' and φ'. The methodology is illustrated using 39 landslides in the Orinda Formation in the San Francisco Bay area. The impact of additional case histories in the same geologic setting, i.., a larger data set, on the required design factor of safety for a given probability of failure is also investigated.

抄録全体を表示

An empirical equation in use for estimating the pseudo-elastic shear modulus, G_f, of subsoil, associated with shear strains less than 0.001% is proposed in this paper. In a series of in-situ seismic cone tests performed nationwide, the profiles of both G_f and the in-situ void ratio, , with depth were successfully characterised at five sites, each comprising a soft clay layer deposited in the Holocene era. The database which comprised the original data from the field and laboratory tests, coupled with similar information on well-documented Holocene clay deposits in Europe, was statistically analyzed in attempts to determine a generalised relationship with which G_f of soft clay may be reasonably estimated only from routinely available borehole data; that is and the current geostatic effective overburden pressure, σ'_v. An empirical relationship, G_f=, 000 -√(σ'_v) (kPa), was derived from the statistical analysis applied to data from seven different clays worldwide, for which extended over a range between 1 and , and the overconsolidation ratio ranged roughly between 1 and 2. The applicability of the proposed relationship was evaluated for two case records, each in which the clay exhibited unusual behavior; i.., the undrained shear strength remained more or less constant with depth due to the existence of artesian pressure at one site, and, at the other, G_f decreased, whereas increased, with depth. It was demonstrated that even in these clay deposits exhibiting exceptional profiles, the proposed relationship was capable of predicting G_f with a reasonable accuracy by determining the profiles of and σ'_v with depth. In addition, the prediction when compared to G_max from carefully performed laboratory cyclic tests, yielded a better estimate of G_f from the in-situ seismic survey. Despite the fact that the empirical relationship was initially designated to estimate G_f of soft clays, it may be equally applicable to sandy deposits. This was verified by comparing it to similar, and well-established, relationships developed for sands. A case record as such is also described for a loose sand deposit at Higashi-Ohgishima in Tokyo Bay which was placed in 1960's by land reclamation.

抄録全体を表示

The (S)-enantiomer of the sex pheromone of the yellow scale (Aonidiella citrina), (S, )--isopropyl-3, -dimethyl-, -decadienyl acetate, was stereoselectively synthesized from (R)-(+)-citronellic acid.

抄録全体を表示