The ability of Climacodon septentrionalis to immobilize and kill a mycophagous nematode (Aphelenchoides sp.) in vitro is described for the first time. Two isolates produced droplets (20–45 μm in diameter) that formed at the apices of tall, stalked, and branching secretory cells (700–

,500 μm tall). On 2% modified malt extract agar, nematodes became enveloped in the droplets, which restricted their ability to move and resulted in complete immobilization and death within several hours of contact. The rate of decomposition of the nematodes varied considerably, with most individuals persisting for weeks whereas others were degraded within several days and appeared to be colonized by dense hyphal growth. This study provides the first documentation of a non-agaricoid fungus producing secretory cells that are able to immobilize nematodes.

抄録全体を表示

The design implication of stress-confinement effect of nonwoven geotextile is addressed. The unconfined and confined strengths of a selected needle-punched nonwoven geotextile are used to conduct a comparative design of a granular soil retaining wall based on a limit equilibrium approach. A higher wall may be allowed when considering the confined strength as compared to the unconfined strength. For a selected wall height, confined strength allows for fewer geotextile layers when compared to that designed using unconfined strength. It is recommended that stress-confinement test procedure should be standardized so that confinement effect of some nonwoven geotextiles may be incorporated into an individual wall design procedure.

抄録全体を表示

The paper presents results from an extensive experimental model study of response of dry sand to impact of a rigid tamper. In the laboratory tests a circular steel tamper was repeatedly dropped on sand contained in a large tank. Measurements included tamper acceleration aud soil pressure at impact, tamper settlement, aud soil densities and strains. Effects of tamper drop height, weight and contact area were investigated. A method is presented for the evaluation of global dynamic stiffness of the soil mass affected by the impact by calculating a dynamic settlement modulus (DSM). The DSM values are determined from integration of the impact acceleration record with respect to time using measured integration constants. DSM values show good correlation to soil densities and corresponding elastic moduli obtained from laboratory tests for loose sand. However, for dense sand, results indicate apparent discrepancies between elastic modulus and the higher DSM values. Analyses of normalized impact energy and the resulting densification in the sand in terms of normalized dimensions of volumetric strain (relative density) contours show unique correlations which are used for a proposed rational design method for dynamic compaction in dry sandy soils.

抄録全体を表示

The possibility of attenuation of microseismic waves due to the presence of an upward folding of the ocean bottom into the liquid is discussed in this paper. The upward folding of the ocean bottom has been idealized by means of an irregularity in the form of a rectangle intruding into the liquid and the evaluation of the displacement component at any point of the solid medium has been carried out in two stages. First, the change in the incident mode of the surface wave due to the presence of the rectangular irregularity has been determined, and second, the subsequent change of the resulting displacement components due to the termination of the liquid layer and the step change in elevation of the solid medium at the continental margin has been discovered. Finally, numerical calculation has been made to determine the attenuation of the microseismic waves of different periods due to the presence of the rectangular irregularity at the ocean bottom.

抄録全体を表示

It has been shown after mathematical and mechanical investigation that Limit Equilibrium Method (LEM) can be considered as a method to obtain the necessary condition of Slip Line Method (SLM), and that the solution can be obtained under the condition that F_s= and ∂F_s/∂θ=O, where F_s is the safety factor and θ is the inclination of the plane on which the safety factor is defined. Next, the generalized LEM (GLEM) is proposed, dealing with the following points : () Triangular or quadrangular blocks can be treated; (2) Safety factors are defined also on interblock planes; and (3) All types of plastic problems, slope stability, bearing capacity, and earth pressure are identically formulated. Two situations regarding treatment of the moment equilibrium condition are discussed. GLEM is applied to well-known problems. The results agree well with those obtained by theoretical methods. GLEM can be used to obtain the distribution of earth pressure or bearing capacity. GLEM, Iike ordinary LEM, is very effective for the practical problems, but GLEM is more theoretical and it can result in more accurate solutions.

抄録全体を表示

A sample of [³H] tobrarnycin (, 000 Ci/Mole) has been synthetized and incubated with
the bacterial ribosome and its subunits. The results obtained show that this antibiotic has
two types of binding sites. The primary one is probably responsible for the inhibition of
protein synthesis whereas the secondary one is probably related to the misreading and reading
tiirough of the messenger RNA.

抄録全体を表示

An empirical equation in use for estimating the pseudo-elastic shear modulus, G_f, of subsoil, associated with shear strains less than .001% is proposed in this paper. In a series of in-situ seismic cone tests performed nationwide, the profiles of both G_f and the in-situ void ratio, , with depth were successfully characterised at five sites, each comprising a soft clay layer deposited in the Holocene era. The database which comprised the original data from the field and laboratory tests, coupled with similar information on well-documented Holocene clay deposits in Europe, was statistically analyzed in attempts to determine a generalised relationship with which G_f of soft clay may be reasonably estimated only from routinely available borehole data; that is and the current geostatic effective overburden pressure, σ'_v. An empirical relationship, G_f=, 000 -√(σ'_v) (kPa), was derived from the statistical analysis applied to data from seven different clays worldwide, for which extended over a range between and , and the overconsolidation ratio ranged roughly between and 2. The applicability of the proposed relationship was evaluated for two case records, each in which the clay exhibited unusual behavior; i.., the undrained shear strength remained more or less constant with depth due to the existence of artesian pressure at one site, and, at the other, G_f decreased, whereas increased, with depth. It was demonstrated that even in these clay deposits exhibiting exceptional profiles, the proposed relationship was capable of predicting G_f with a reasonable accuracy by determining the profiles of and σ'_v with depth. In addition, the prediction when compared to G_max from carefully performed laboratory cyclic tests, yielded a better estimate of G_f from the in-situ seismic survey. Despite the fact that the empirical relationship was initially designated to estimate G_f of soft clays, it may be equally applicable to sandy deposits. This was verified by comparing it to similar, and well-established, relationships developed for sands. A case record as such is also described for a loose sand deposit at Higashi-Ohgishima in Tokyo Bay which was placed in 1960's by land reclamation.

抄録全体を表示

2-Benzyl--chloro--mercapto-3 (2H)-pyridazinone () was heated in ethanol under reflux for 10 hours to form concurrently 2, -dibenzyldipyridazo [, - : ', '-]-, -dithiin-, (2H, H)-dione (Ia) (57% in yield) and 2, -dibenzyldipyridazo [, - : ', '-]-, -dithiin-, 9 (2H, H)-dione (IIa) (14% in yield). Assignment of the two products to the corresponding structures is established by their physico-chemical constants and chemical behaviors. The concurrent formation of the dipyridazo [, - : ', '-]-, -dithiin-, (2H, H)-dione and the -, 9 (2H, H)-dione were observed in, not only heating -chloro--mercapto-3 (2H)-pyridazinones (-3) in polar solvent, but warming -mercapto--chloro-3 (2H)-pyridazinones (-) in the presence of potassium carbonate in DMF. For the interpretation of the reaction, keto-thioketo carbenes as active intermediate species and a reversible interconversion among them are suggested on the basis of the fact that there was nonexistence of an equilibrium between the two compounds, such as Ia and IIa, under the reaction condition and a trapping keto-thioketo carbene species as 2-phenylimino--benzylpyridazo [, -]-, 3-dithiol- (H)-one (IVa) (14% in yield) along with the major products, (Ia) and (IIa), was furnished by warming with phenylisothiocyanate in the presence of triethylamine in dry benzene. On the contrary, participation of a reversible interconversion between Ia and IIa, to a considerable extent, with the concurrent formation of them in the case of benzylation of either Ib or IIb, by warming with benzylchloride in the presence of potassium carbonate in DMF at 80°, might not be neglected, because an attempted approach to an equilibrium between Ia and IIa in a similar reaction condition except the use of benzylchloride realized, whereas non-existence of an equilibrium between Ib and IIb in the similar reaction condition was observed.

抄録全体を表示

A boron treated copper bearing HSLA steel containing austenite formers like manganese and nickel, somewhat lower in amount than that in HSLA 100 variety of steel is chosen for the study. The role of thermomechanical processing on the microstructure and mechanical properties of the above steel has been investigated. Differential scanning calorimetric study is carried out for understanding the precipitation behaviour of copper in HSLA steel under the influence of boron. The microstructure of the experimental steel is found to consist of laths of martensites and bainite. MA constituents of ribbon like morphology are observed at the lath boundaries. Higher strength properties of the steel are attributed to the presence of finely distributed precipitates of copper and microalloy carbides.

抄録全体を表示

In this paper, consideration is given as to how to characterize depth-variation for the small-strain shear modulus of natural clay sedimentation, in a state of normal consolidation. A case study was carried out for a relatively uniform clay layer deposited in the Holocene era. Initially, the effects of both strain and in-situ stress levels on secant shear modulus were carefully examined in cyclic torsion shear tests using undisturbed samples, which were recovered at different depths in a test borehole. The range of shear strain examined was between .001% and %. Similar examination was made for a silty clay using reconstituted samples that were isotropically consolidated at different stress levels. On the basis of the results of these laboratory tests, together with the shear modulus from an in-situ seismic survey, the small-strain shear modulus was formulated in terms of the stress and strain levels, and linked also to undrained shear strength. Interactions of the small strain stiffness between in-situ and laboratory are discussed in depth with an attention paid to the existing aging effect in the original subsurface condition.

抄録全体を表示

Natural sedimentary clays exhibit ageing effects on their behaviour when subjected to both consolidation and shearing. Attempts to characterising the in-situ 'structure'of soft marine clays have been made in case studies performed in Ariake (Japan) and in Bangkok (Thailand), each showing a typical profile of aged clay-structure with depth reflecting its site-specific geological consolidation history. In each site, profiles of Atterberg limits, natural water content, overconsolidation ratio (OCR), quasi-elastic shear modulus G_max and the undrained shear strength c_u with depth were attained from various laboratory tests, together with the a comparable profile of quasi-elastic shear modulus from insitu seismic survey G_f. Quantitative assessment of the aged clay-structure was made by using two different measures, metastability index MI (G) and the soil constant reflecting structure S (Jamiolkowski et al., 1994). The profiles of MI (G) and the S-value with depth were both determined based on the corresponding G_max behaviour of the reconstituted sample. "Disturbance"of laboratory samples retrieved by using two different samplers (i.., Laval and Japanese thin-walled samplers) with two different sampling techniques (i.., pre-boring and displacement methods) was discussed. A new approach to estimate c_u"in the ground", termed by the authors the MILK (Metastability Index coupled with Laboratory K_o test) method, is proposed. A trial of the MILK-method is demonstrated in soft Bangkok clay, the texture of which is similar to "soft cheese".

抄録全体を表示

This paper provides a comprehensive survey of the numerical methods related to geotechnical problems, most of which were reported in papers appearing in Soils and Foundations. The reason why most of the reviewed papers are concentrated in Soils and Foundations is that if we were to include papers appearing in other journals in the field of geotechnical engineering, closely related to numerical methods, .g., Computers and Geotechnics, Int. J. Numer. Anal. Meth. Geomech., etc., we would have to deal with almost all the papers in those journals. Firstly, we present a description of the current status of the numerical methods, and then give a brief review of the literature covering several topics in geotechnical applications. The scope of the review is limited, and thus, the authors do not profess to cover the entire range of literature.

抄録全体を表示

Two new partially saturated tricyclic ring systems, , a, , , 9, 10, 10a, 11-octahydro-11-oxodibenz [, ] oxepins (3a and 3), and -thiepins (a and ) were synthesized. Compounds a and were desulfurized to give a pair of isomeric 2-methylbenzoylcyclohexanes (10a and 10). Deuterated a and (11a and 11) were prepared starting from butadiene- (12). The stereochemical features of 3a (trans), 3 (cis), a (trans) and (cis) are compared with those of 10a, 10, 11a and 11 on the basis of proton nuclear magnetic resonance data.

抄録全体を表示

The phase diagrams of the Ni-Mo- and Ni-W- ternary systems in the region of less than 50mol% were constructed by thermodynamic calculation, based on the data obtained by thermodynamic measurement of the related materials. We found three ternary eutectic points and three or two ternary peritecto-eutectic points as follows:
:L (1365K, 71.mol%Ni-.mol%Mo-.mol%)=(Ni)++
:L (1355K, 62.mol%Ni-2.mol%Mo-30.mol%)=++
:L (1445K, 42.mol%Ni-30.mol%Mo-10.3mol%)=(Ni)+NiMo+
:L (1812K, 34.9mol%Ni-42.3mol%Mo-.mol%)+MoB=+
P₂:L (1633K, 42.3mol%Ni-40.mol%Mo-17.3mol%)+Mo=+
P₃:L (1812K, 53.mol%Ni-33.mol%Mo-12.mol%)+Mo=NiMo+
:L (1622K, 51.mol%Ni-31.mol%W-17.mol%)=(Ni)+W+
:L (1260K, 71.mol%Ni-.mol%W-.mol%)=(Ni)++
:L (1291K, 65.mol%Ni-.mol%W-29.mol%)=++
:L (2115K, 23.mol%Ni-43.mol%W-33.mol%)+WB=+
P₂:L (1657K, 48.9mol%Ni-33.mol%W-18.mol%)+=W+
The calculated phase diagrams are expected to be useful for the development of new Ni-based heat-, corrosion- or wear-resistance alloys.

抄録全体を表示

A comparative study of the static and dynamic response of a slope is carried out, using the large deformation theory of the updated Lagrangian formulation and the conventional infinitesimal theory. In the static analysis, a strength reduction method proposed by one of the authors is used to evaluate the safety factor of the slope. It is found that by the large deformation theory, the safety factor is larger than that calculated by the infinitesimal theory, and this difference becomes large along with the reduction of elastic modulus. In the dynamic analysis, it is observed that the large deformation theory gives smaller sliding displacement and larger response acceleration than the infinitesimal approach. It is concluded that in many cases the large deformation approach gives more adequate solutions.

抄録全体を表示