A method for analyzing the uncertainties involving the use of empirical relationships in design is developed. It is applied to evaluate the reliability of the relationship s_u(mobilized)=(measured), whereby the pertinent uncertainties are analyzed using extensive laboratory and field observed data. On the average, the relationship s_u(mobilized)= (measured) is unbiased and the error implicit in the relationship is about 15%. When cone values are used to infer s'_p, additional uncertainties on the mobilized undrained strength will incur resulting mainly from the calibration uncertainty between σ'_p and the cone values. Alternatively, vane tests may be performed to infer the mobilized strength using Bjerrum correction factor. Results show that uncertainty level associated with using the vane tests is smaller than that using the cone values, provided that similar scatter is observed between measured vane and cone values at a given site. However, prediction of the mobilized strength is even more accurate if direct measurements can be made on the preconsolidation pressure. The proposed probabilistic method also assesses the benefit of additional tests besides comparing the accuracy of using various soil parameters for predicting mobilized undrained strength. Such information is essential for planning cost-effective site characterization program.

抄録全体を表示

This paper presents reinforcing mechanisms and a method for analyzing reinforced earth structures. The reinforcing mechanism presented is divided into two stages, a fixed slip surface and an arbitrarily selected slip surface. The mechanism is studied through direct shear tests and plane strain compression tests including some geotextiles. The reinforcing materials considered in this paper only have tensile strength. The authors have already proposed a method called Generalized Limit Equilibrium Method (GLEM) for analyzing stability problems. The validity of the method has already been shown in previously published papers. In this paper, the method is extended to carry out a stability analysis for reinforced earth structures. Finally, large scale model tests for the bearing capacity of foundations on reinforced slopes were carried out to investigate the validity of the proposed reinforcing mechanism and the analytical method. Through comparisons of observations of experiments and results of the analytical method, the validity of the present work is demonstrated.

抄録全体を表示

Two new polyacetylene compounds (4, , 12)-1-acetoxy--isovaleryloxytetradeca-4, , 12-trien-, 10-diyn-14-ol (), and (4, , 12)-1-acetoxy--(2-methylbutyryloxy)tetradeca-4, , 12-trien-, 10-diyn-14-ol (C) have been isolated along with (4, , 12)-1-acetoxy--senecioyloxytetradeca-4, , 12-trien-, 10-diyn-14-ol (A) from Atractylodes Rhizome (Karabyakujutu). The structures of these compounds were determined on the basis of their spectral data.

抄録全体を表示

By employing an undrained cyclic loading ring-shear apparatus, a series of tests to reproduce the dynamic behavior of the Nikawa landslide induced by the January 17, 1995 Hyogoken-Nambu earthquake, is conducted. The test sample is Osaka-group coarse sandy soil taken from the landslide. The initial stress condition acting on a soil element in the sliding surface is applied to the sample. Based on the seismic records monitored at the JR Takarazuka Station, the input seismic wave is synthesized to reproduce the seismic stress acting on the sliding surface. The test results show that the soil failed due to the dynamic loading of the earthquake. The most important results are the excess pore water pressure generation and the acceleration of shear displacement continuing after the main shock. Combined with the grain crushing at the shear zone and the volume reduction in the drained constant-speed ring-shear test, the mechanism of this landslide is interpreted as, shear displacement causing grain crushing in the shear zone and volume reduction, and then resulting in a localized liquefaction phenomenon, "sliding-surface liquefaction". This geotechnical simulation test provides a reasonable interpretation of this highly mobile landslide.

抄録全体を表示

The pseudo-static analysis has been used in engineering practice to simplify the computation of the upper limit of a slope under seismic load. In this paper, the upper bound technique of limit analysis of perfect plasticity is used to determine the bearing capacity of a foundation near a down-hill slope. In this analysis (Chen et al., 1969; Chen, 1975), a logarithmic spiral rapture (Abdul-Baki et al., 1970; Sawada et al., 1984) is assumed to start at an edge of the loaded area far from the slope. A landslide is assumed to be of rigid body type with the inertia force acted at its center of gravity. The collapse state is reached when the rate of kinematic energy of the landslide together with the load is equal to the rate of dissipation of internal energy along the sliding surface. This energy balance leads to the equation of ultimate load with several parameters. The optimized numerical rcsults with respect to these parameters are compared with those by Kotter's method (Yamaguchi, 1959) and those obtained by the slice method.

抄録全体を表示

The characteristic mechanical activities of the smooth muscles found in all organs of the body are highly variable and depend mainly on the spatial arrangement of the muscle cells and the stroma: mass, orientation, relationships, links, constraints, which are deployed in various configurations. These structural features are examined here for their mechanical relevance, in light and electron microscopic views of several muscles of viscera and blood vessels, in a selection of mammalian species. Smooth muscles are incompressible and therefore maintain constant volume. They do not have available space and any movement of a part requires displacement of another part. Most of them have no terminations or points of attachment, and in hollow organs such as intestines, blood vessels and uro-genital tract they usually form structures closed onto themselves, such as rings or bag-like containers In these situations, changes in the size of the lumen is achieved very efficiently by a concentric inward enlargement that accompanies muscle contraction. The longitudinal arrangement of collagen blocks an elongation of small blood vessels upon contraction, further enhancing the efficiency of lumen reduction. In other muscles, links between layers and special arrangements of the stroma allow both shortening and elongation of a tubular organ to occur. The mechanics of smooth muscles has many characteristic features (some unique, some shared with those of hydrostats, some at variance with other muscles) and histological data are a contribution to our understanding of these properties.

抄録全体を表示

All the cells of rat detrusor muscle fall into one of five ultrastructural types: muscle cells, fibroblasts, axons and glia, and vascular cells (endothelial cells and pericytes). The tissue is ~79% cellular and 21% non-cellular. Muscle cells occupy 72%, nerves ~4% (1/

axons, 2/ glia), and fibroblast >% of space. Muscle cells (up to µm across and ~600 µm long, packed to almost 100,000 per mm²) have surface-to-volume ratio of 2.4 µm²/ ~93% of cell volume is contractile apparatus, .1% mitochondria and 2.5% nucleus. Cell profiles are irregular but sectional area decreases regularly towards either end of the cell. Muscle cells are gathered into bundles (the mechanical units of detrusor), variable in length and size, but of constant width. The musculature is highly compact (without fascia or capsule) with smooth outer surfaces and extensive association and adhesion between its cells. Among many types of intercellular contact and junction, digitations are very common, each muscle cell issuing minute finger-like processes that abut on adjacent cells. Sealed apposition are wide areas of specialized contact, possibly forming a chamber between two muscle cells, distinct from the extracellular space at large (stromal space). The innervation is very dense, virtually all intramuscular axons being varicose (including afferent ones). There are identifiable neuro-muscular junctions on each muscle cell, often several junctions on a single cell. There are also unattached terminals. Fibroblasts (involved in the production of collagen), ~1% of the total number of cells, do not make specialized contacts.

抄録全体を表示

It has been shown after mathematical and mechanical investigation that Limit Equilibrium Method (LEM) can be considered as a method to obtain the necessary condition of Slip Line Method (SLM), and that the solution can be obtained under the condition that F_s=1 and ∂F_s/∂θ=O, where F_s is the safety factor and θ is the inclination of the plane on which the safety factor is defined. Next, the generalized LEM (GLEM) is proposed, dealing with the following points : (1) Triangular or quadrangular blocks can be treated; (2) Safety factors are defined also on interblock planes; and () All types of plastic problems, slope stability, bearing capacity, and earth pressure are identically formulated. Two situations regarding treatment of the moment equilibrium condition are discussed. GLEM is applied to well-known problems. The results agree well with those obtained by theoretical methods. GLEM can be used to obtain the distribution of earth pressure or bearing capacity. GLEM, Iike ordinary LEM, is very effective for the practical problems, but GLEM is more theoretical and it can result in more accurate solutions.

抄録全体を表示

The objective of this article is to propose and evaluate a sliding-block model to deal with very large displacements of slopes when a horizontal earthquake is applied. The slip surface consists of two inclinations on which full shear resistance is mobilized. Internal shearing exists along a sub-plane that intersects the angle between the two sub-planes that form the external slip surface. The ratio of the distance moved along the two external sub-planes depends on the inclination of the internal sub-plane. If there is a water table line, undrained conditions are assumed during motion and total stress analysis is performed. The governing equations of motion are formulated, analytical solutions are obtained for some cases, and back-analysis of four well-documented slides is performed.

抄録全体を表示

This paper is concerned with an extension of a rotational limit equilibrium method for determining the permanent displacements of slopes under seismic excitation. In the proposed procedure, the sliding mass is treated as a rigid rotating body defined by a log spiral trace. Permanent displacements are obtained by double-integration of the equation of motion in a manner similar to Newmark's translational sliding block method. The seismic slope stability analysis is based on the rotational (variational) limit equilibrium approach. This stability analysis was verified with dynamic experimental results obtained from centrifuge model testing. A series of parametric studies was conducted on"unstable"slopes, investigating the effects of soil properties and characteristics of excitation on the magnitude of permanent displacements. The higher the frictional angle, the smaller the permanent displacement of the slope is. Low excitation frequency yields larger slope displacement if the excitation is extended for the same time period of time. The effect of frequency becomes less distinct when a larger value of yield seismic coefficient is used. The proposed procedures produce a rational criterion to evaluate the seismic performance of simple slopes. This criterion is based on permanent displacement limit rather than factor of safety alone.

抄録全体を表示

Two new partially saturated tricyclic ring systems, , a, 7, , , 10, 10a, 11-octahydro-11-oxodibenz [, ] oxepins (a and ), and -thiepins (4a and 4) were synthesized. Compounds 4a and 4 were desulfurized to give a pair of isomeric 2-methylbenzoylcyclohexanes (10a and 10). Deuterated 4a and 4 (11a and 11) were prepared starting from butadiene- (12). The stereochemical features of a (trans), (cis), 4a (trans) and 4 (cis) are compared with those of 10a, 10, 11a and 11 on the basis of proton nuclear magnetic resonance data.

抄録全体を表示

The correction factor (η_ie) for the ultimate bearing capacity of a footing placed adjacent to a slope, taking into account the combined effect of horizontal and vertical seismic loads, represented by horizontal and vertical seismic coefficients, k_h and k_v, respectively, was derived using a modified Janbu's slice method. The influence of slope angles ‘α’ on the values of ‘η_ie’ are studied here. It was found that the values of η_ie can be expressed as an exponential function of ‘k_h/(1-k_v)’ and ‘α’, with a measurable interdependency between ‘α’ and ‘η_ie’. The influence of ‘α’ on the value of ‘η_ie’ increases as the input value of ‘k_h/(1-k_v)’ increases. Equations derived based on the analytical results are proposed to account for this effect. Based on the analyses of 11 near-fault seismographers obtained in the 1999 Chi-Chi earthquake in Taiwan, a ratio between the vertical and the horizontal seismic coefficients, λ, of between ±0.25 is suggested for including the combined effect of vertical and horizontal seismic forces in evaluating the seismic bearing capacity of footings located in near-fault areas.

抄録全体を表示

At present, analytical or empirical formula for seismic bearing capacity of footings adjacent to slopes is not available. This study uses a pseudo-static-based approach in conjunction with rigorous Janbu's slice method to derive analytical values of seismic bearing capacity factors (N_γ) and correction factors for the effects of inertia of soil mass and load inclinations for a rigid footing adjacent to cohesionless slopes. It is shown that both the bearing capacity factors (N_γ) and the correction factors for the seismic bearing capacity of footings placed on level ground derived herein are comparable with those reported in the literature. Empirical equations regarding the effects of slope angles and load inclinations, expressed using generalized forms of those proposed in the literature, are also derived. It is also found that the empirical equations derived in the present study provide values of correction factors in good agreements with the analytical ones, indicating the validity of using these empirical equations for assessing the bearing capacity of rigid footings situated on the slope subjected to pseudo-static seismic loading.

抄録全体を表示

We screened the differentiation-inducing activities of 39 mushroom extracts from Akita prefecture, Japan, on the mouse osteoblastic cell line, MCT-1. Sixteen phosphate buffered saline (PBS), boiled PBS, 14 ethanol and 12 methanol extracts induced alkaline phosphatase (ALP) activities, an indicator of MCT-1 cell differentiation. The enzyme activities were markedly induced by extracts of Tricholoma auratum, and we isolated the active compound from methanol extracts of this mushroom. Physical data for the isolated active compound were identical to those for (,24R)-ergosta-7,-diene-,5α,-triol (1). 1 induced ALP activities of MCT-1 cells and promoted cell proliferation. To investigate the relationships between the chemical structure and differentiation-inducing activity of the compound, ALP-inducing activities of MCT-1 cells by 1, ergosterol (2), ergocalciferol (), cholesta-,5α,-triol (4), 7-dehydrocholesterol (5) and cholecalciferol () were tested. The enzyme activities of MCT-1 cells were increased .0-fold by 10 μM 1 and 2.4-fold by 10 μM 4. However, 2, , 5 and did not induce MCT-1 cell ALP activity at 0.1—10 μM. These results suggested that the OH groups at C-5 and/or C- of 1 and 4 played an important role in their differentiation-inducing activities on MCT-1 cells. Furthermore, 1 suppressed induction of MCT-1 cell apoptosis by serum starvation.

抄録全体を表示

The Beckmann rearrangement of aliphatic ketone oximes, R(CHs)C=NOH (R=Et (1); n-Pr (2); iso-Pr (); iso-Bu (4)), with polyphosphoric acid (PPA), polyphosphate ester (PPE), and ester of phosphoric acid (2 P-5 R) was carried out and migratory ratios ((a)/() in eq. (1)) were determined, The results are shown in Fig.1, 2, and , respectively.
In Fig.1 and 2, the migratory ratios decrease with reaction time and nearly approach to the ratios of anti-alkyl form/syn-alkylform in benzene(A1) or DMSO(A2)except for () (See Table 1). From this fact, it has been found that PPA and PPE are inactive for isomerization of the oximes andanti-alkyl oximes rearrange faster than syn-alkyl ones. ln the case of (), migratery ratios are smaller than Ai or A2. As acetonitrile is detected by GLC, it is presumed that fission has been occurred simultaneously with rearrangement in anti-alkyl oxime (eq. ()). In the case of 2 P-5 R, all modes of the reaction arethe same as in above, except that the rate of fission is tnuch faster than that in PPA and PPE.
The reaction of anti-alkyl ketone oximes having a bulky grouphas been greatly influenced by the use of sterically demanding catalysts such asPPA, PPE, and 2 P-5 R.

抄録全体を表示