The Gujarat earthquake in India occurred in January, 2001, and caused significant damage in the province of Gujarat. The Japanese Geotechnical Society sent a small reconnaissance team to the damaged region after the quake. The present text presents the report from this activity. The major attention of the team was focused on geotechnical aspects of the damage which were related to earthfill dams and harbor land fills. It was found that a significant portion of damage was concentrated in fills resting on soft natural soils. Swedish weight soundings which were conducted at two places demonstrated the existence of such a soft subsoil. From this, it was concluded that amplification of earthquake shaking as well as the permanent deformation in the soft foundation soil induced such kinds of damage as subsidence, cracking, and lateral spreading in overlying artificial fills. For the better seismic resistance of those affected fills during future earthquakes, the improvement of soft subsoil seems essential.

抄録全体を表示

The boundary element method expanded in frequency domains is presented to analyze the dynamic interaction between an embedded flexible rectangular foundation and soil with consideration of the obliquely incident waves. Numerical results describing the influence of the flexibility of the foundation on the dynamic responses of the foundation due to obliquely incident waves indicate that the flexibility of actual foundations can diminish the reduction of translation responses and increase the rotational responses in the high frequency range. These phenomena are more conspicuous as the embedment ratio is larger and the value of the wave velocity ratio of the soil and the foundation approaches to unity. When the high frequency components of the input ground motion are important and the basement has higher flexibility (for example ₂v_s/₁v_s >.), the analysis method which considers the basement as a rigid foundation may lead to unsafety estimations and the estimation of the flexibility of the foundation is necessary as analysing the effective input motion with consideration of the incident waves.

抄録全体を表示

The phase diagrams of the Ni-Mo- and Ni-W- ternary systems in the region of less than 50mol% were constructed by thermodynamic calculation, based on the data obtained by thermodynamic measurement of the related materials. We found three ternary eutectic points and three or two ternary peritecto-eutectic points as follows:
:L (1365K, 71.mol%Ni-.mol%Mo-.mol%)=(Ni)++
:L (1355K, 62.mol%Ni-2.mol%Mo-30.mol%)=++
:L (1445K, 42.mol%Ni-30.mol%Mo-10.3mol%)=(Ni)+NiMo+
P₁:L (1812K, 34.mol%Ni-42.3mol%Mo-.mol%)+MoB=+
P₂:L (1633K, 42.3mol%Ni-40.mol%Mo-17.3mol%)+Mo=+
P₃:L (1812K, 53.mol%Ni-33.mol%Mo-12.mol%)+Mo=NiMo+
:L (1622K, 51.mol%Ni-31.mol%W-17.mol%)=(Ni)+W+
:L (1260K, 71.mol%Ni-.mol%W-.mol%)=(Ni)++
:L (1291K, 65.mol%Ni-.mol%W-29.mol%)=++
P₁:L (2115K, 23.mol%Ni-43.1mol%W-33.1mol%)+WB=+
P₂:L (1657K, 48.mol%Ni-33.1mol%W-18.mol%)+=W+
The calculated phase diagrams are expected to be useful for the development of new Ni-based heat-, corrosion- or wear-resistance alloys.

抄録全体を表示

2-Benzyl--chloro--mercapto-3 (2H)-pyridazinone (1) was heated in ethanol under reflux for 10 hours to form concurrently 2, -dibenzyldipyridazo [, - : ', '-]-1, -dithiin-1, (2H, H)-dione (Ia) (57% in yield) and 2, -dibenzyldipyridazo [, - : ', '-]-1, -dithiin-1, (2H, H)-dione (IIa) (14% in yield). Assignment of the two products to the corresponding structures is established by their physico-chemical constants and chemical behaviors. The concurrent formation of the dipyridazo [, - : ', '-]-1, -dithiin-1, (2H, H)-dione and the -1, (2H, H)-dione were observed in, not only heating -chloro--mercapto-3 (2H)-pyridazinones (1-3) in polar solvent, but warming -mercapto--chloro-3 (2H)-pyridazinones (-) in the presence of potassium carbonate in DMF. For the interpretation of the reaction, keto-thioketo carbenes as active intermediate species and a reversible interconversion among them are suggested on the basis of the fact that there was nonexistence of an equilibrium between the two compounds, such as Ia and IIa, under the reaction condition and a trapping keto-thioketo carbene species as 2-phenylimino--benzylpyridazo [, -d]-1, 3-dithiol- (H)-one (IVa) (14% in yield) along with the major products, (Ia) and (IIa), was furnished by warming 1 with phenylisothiocyanate in the presence of triethylamine in dry benzene. On the contrary, participation of a reversible interconversion between Ia and IIa, to a considerable extent, with the concurrent formation of them in the case of benzylation of either Ib or IIb, by warming with benzylchloride in the presence of potassium carbonate in DMF at 80°, might not be neglected, because an attempted approach to an equilibrium between Ia and IIa in a similar reaction condition except the use of benzylchloride realized, whereas non-existence of an equilibrium between Ib and IIb in the similar reaction condition was observed.

抄録全体を表示

In view of the significant role of the water film effect in flow failure for a liquefied sandy deposit, the mechanism of water film generation is numerically studied based on a 1-dimensional model test. The process of water film growth and decay can be simulated to a certain extent by a simple consolidation analysis, which indicates that only a small difference in permeability in layered sand is enough for a water film to develop. A 1 G shaking table test for a two-dimensional slope model with an arc of silt within a saturated sand is then addressed to discuss the dilatancy effect exerted in sheared sand during flow failure. It is possible that, once the water film is formed, the transmission of shear stress through it is interrupted, leaving the sand below free from the dilatancy ; this eventually allows the water film to stay without being absorbed during flow failure. The result of another shaking table test for a trapezoidal slope with horizontal silt seams indicate that water films beneath the seams enable the soil mass above them to laterally flow along water films very gently inclined even after shaking. If a silt seam breaks due to excessive pressure in the water film, it triggers re-liquefaction in the upper sand and leads to further instability.

抄録全体を表示

The paper presents results from an extensive experimental model study of response of dry sand to impact of a rigid tamper. In the laboratory tests a circular steel tamper was repeatedly dropped on sand contained in a large tank. Measurements included tamper acceleration aud soil pressure at impact, tamper settlement, aud soil densities and strains. Effects of tamper drop height, weight and contact area were investigated. A method is presented for the evaluation of global dynamic stiffness of the soil mass affected by the impact by calculating a dynamic settlement modulus (DSM). The DSM values are determined from integration of the impact acceleration record with respect to time using measured integration constants. DSM values show good correlation to soil densities and corresponding elastic moduli obtained from laboratory tests for loose sand. However, for dense sand, results indicate apparent discrepancies between elastic modulus and the higher DSM values. Analyses of normalized impact energy and the resulting densification in the sand in terms of normalized dimensions of volumetric strain (relative density) contours show unique correlations which are used for a proposed rational design method for dynamic compaction in dry sandy soils.

抄録全体を表示

Stress wave theory is applied to open-ended pipe piles to clarify the effects of soil plug on the behaviour of piles during driving and static loading. Measured field data and various numerical models are reviewed ; methods are presented to calculate wave propagation in both the pile and the soil plug ; modelling is presented which takes into account the interaction between the soil plug and the pile ; also presented is simplified method to estimate the loadsettlement relation of the pipe pile in static loading. By correlating observed and calculated values in two analytical cases, the authors demonstrate that incorporation of the soil plug (modelled as a series of masses and springs) is required to correctly predict pile behaviour during driving and static loading.

抄録全体を表示

The ability of Climacodon septentrionalis to immobilize and kill a mycophagous nematode (Aphelenchoides sp.) in vitro is described for the first time. Two isolates produced droplets (20–45 μm in diameter) that formed at the apices of tall, stalked, and branching secretory cells (700–1,500 μm tall). On 2% modified malt extract agar, nematodes became enveloped in the droplets, which restricted their ability to move and resulted in complete immobilization and death within several hours of contact. The rate of decomposition of the nematodes varied considerably, with most individuals persisting for weeks whereas others were degraded within several days and appeared to be colonized by dense hyphal growth. This study provides the first documentation of a non-agaricoid fungus producing secretory cells that are able to immobilize nematodes.

抄録全体を表示

This study was performed to clarify which factors affected damage to tame-ike (small embankment dams for irrigation) in Hokudan Town as a result of the January 17, 1995 Hyogoken-Nambu earthquake. Factors were assumed to be : Location (.g., Distance to Epicenter, etc.), Structure (.g., Angle to Nearest Fault, Embankment Volume, etc.), Soil Properties of Embankment, Geology of Dam Site and History (Era of Construction, Repaired, etc.). Multivariate statistical analyses were performed for documentary data (damaged : 181, undamaged : 328). Ordinary statistical analyses were conducted for the data investigated in situ for soil properties of the embankment. The results show that the factors causing damage to dam are : (1) Nearest Fault (Nojima, Mizukoshi and D2), (2) Distance to Nearest Fault (less than 500 m), (3) Distance to Epicenter (approximately to 14 km, which almost agrees with the location of seismic intensity JMA), () Elevation of Dam Site (higher than 100 m), () Embankment Volume (the greater the volume the more damage was caused), () Direction of Dam Axis (normal or diagonal to the epicenter or to nearest the fault), () Plan View of Dam Axis (3 or axes), () Surface Geology of Dam Site (non-cohesive soil type ground), () Era of Construction (prior to 1891) and (10) Soil Properties of Embankment (sand, not silty sand or gravel, penetration resistance that is 10% smaller than the undamaged dams).

抄録全体を表示

Two new partially saturated tricyclic ring systems, , a, , , , 10, 10a, 11-octahydro-11-oxodibenz [, ] oxepins (3a and 3), and -thiepins (a and ) were synthesized. Compounds a and were desulfurized to give a pair of isomeric 2-methylbenzoylcyclohexanes (10a and 10). Deuterated a and (11a and 11) were prepared starting from butadiene- (12). The stereochemical features of 3a (trans), 3 (cis), a (trans) and (cis) are compared with those of 10a, 10, 11a and 11 on the basis of proton nuclear magnetic resonance data.

抄録全体を表示

The design implication of stress-confinement effect of nonwoven geotextile is addressed. The unconfined and confined strengths of a selected needle-punched nonwoven geotextile are used to conduct a comparative design of a granular soil retaining wall based on a limit equilibrium approach. A higher wall may be allowed when considering the confined strength as compared to the unconfined strength. For a selected wall height, confined strength allows for fewer geotextile layers when compared to that designed using unconfined strength. It is recommended that stress-confinement test procedure should be standardized so that confinement effect of some nonwoven geotextiles may be incorporated into an individual wall design procedure.

抄録全体を表示

This paper provides a comprehensive survey of the numerical methods related to geotechnical problems, most of which were reported in papers appearing in Soils and Foundations. The reason why most of the reviewed papers are concentrated in Soils and Foundations is that if we were to include papers appearing in other journals in the field of geotechnical engineering, closely related to numerical methods, .g., Computers and Geotechnics, Int. J. Numer. Anal. Meth. Geomech., etc., we would have to deal with almost all the papers in those journals. Firstly, we present a description of the current status of the numerical methods, and then give a brief review of the literature covering several topics in geotechnical applications. The scope of the review is limited, and thus, the authors do not profess to cover the entire range of literature.

抄録全体を表示

Stereoselective synthesis of the , -syn, , -anti adducts (14 and 16) on the aldol condensation of the Z (O)-lithium enolate, derived from the -enone (2), to α-alkoxy aldehydes (12 and 13) was proved via the successive intramolecular Diels-Alder reaction.

抄録全体を表示

A sample of [³H] tobrarnycin (, 000 Ci/Mole) has been synthetized and incubated with
the bacterial ribosome and its subunits. The results obtained show that this antibiotic has
two types of binding sites. The primary one is probably responsible for the inhibition of
protein synthesis whereas the secondary one is probably related to the misreading and reading
tiirough of the messenger RNA.

抄録全体を表示

This study aimed to determine the prevalence of fecal carriage of extended spectrum β-lactamase (ESBL) and/or plasmidic AmpC β-lactamase (pAmpC) producing Escherichia coli among dogs (n=428) in Turkey. Polymerase chain reaction (PCR) and sequencing were used to characterize genes encoding β-lactamase and plasmid mediated quinolone resistance (PMQR). Antimicrobial susceptibility testing and PCRs for virulence genes and phylogenetic groups were also performed. Cefotaxime resistant

. coli isolates were detected in 95 (.2%) of the swab samples. Sequencing analysis results showed occurrence of various β-lactamase genes: bla_CTX-M-15 (62), blaTEM-

1b

(42), bla_CMY-2 (

22

), bla_CTX-M-3 (16), bla_CTX-M-1 (15), bla_OXA-1 (

9

) and bla_SHV-12 (3) alone or in combination. The most frequently encountered phylogenetic group was group A₁ (35.

8

%), followed by group D₂ (

22

.1%),

B

1 (15.

8

%), D₁ (

9

.

5

%),

A₀

(

7

.

4

%),

B2₂

(

5

.3%) and

B2₃

(

4

.2%), respectively. PMQR genes, aac(

6

’)-Ib-cr, qnrS1 and qnrB10 were detected in 25.3, 10.

5

and 1.1% of the isolates, respectively. While all isolates were susceptible to imipenem and amikacin, resistance rates to non-β-lactam antibiotics ranged from 20.

0

% for tobramycin to 56.

8

% for tetracycline. The virulence genes were only detected in 34 (36.2%) of the isolates and this isolates carried single or various combination of virulence genes of iucD, papC, papE, f17a-A and eaeA. Four isolates were identified as human virulent pandemic CTX-M-15 producing

E

. coli clone O25

b

:ST131/

B

2. To the best of our knowledge, this is the first study to show fecal carriage of ESBL/pAmpC type β-lactamase producing

E

. coli isolates among dogs in Turkey.

抄録全体を表示

In the seismic analysis of pile foundations the soil is often assumed to be an elastic material and the pressure at the soil pile interface is not limited during the analysis. This may result in a considerable error, as the computed pressure from an elastic analysis may go well beyond the ultimate lateral pressure of real soil. In fact, significant yielding at the soil-pile interface has been observed during real earthquakes, and also in laboratory tests. The yield zone is usually near the ground surface where the effect of inertial force due to the superstructure is higher. This yielding redefines the pile response, and in general cannot be ignored. In order to examine the effects of soil yielding on the internal pile response during earthquakes an approximate analysis is described in this paper which is an extension of a static method developed by the second author (1982) for the analysis of piles subjected to lateral soil movement. This method is then used to investigate the effects of soil yielding on the internal response of piles through a comparative study in which real earthquakes are used. It is shown that for strong earthquakes and heavily loaded piles the soil yielding may considerably increase the amount of maximum pile moment developed in the pile. A marked difference in the effects of yielding on the pile moment and shear is observed and discussed.

抄録全体を表示

The interaction between a penetrating shaft and the surrounding soil media under impact loading is a frequently encountered phenomenon in geotechnical engineering. Examples of such dynamic soil/shaft interaction would include dynamic pile driving, standard penetration testing (SPT), and dynamic driven rod test. Presented in this paper is a novel approach, based on the principle of dynamic system identification, which enables identification of dynamic soil-pile interaction model parameters. The analytical transfer function, relating the output stress wave forms to the input stress wave forms in the soil/shaft system, is derived using the Laplace and Fourier Transform techniques and the one-dimensional wave propagation theories. A numerical solution algorithm based on a variation of gradient method is coded into a micro-computer based program to solve the frequency-dependent soil-pile interaction parameters (Smith model) : soil damping and soil spring stiffness. To further reduce the amount of computational effort required in the solution of the frequency-dependent dynamic soil properties, it is suggested that the solution be obtained for the first-mode natural frequency of the measured stress waves. The results obtained from this simplified solution algorithm, when compared with both numerical simulations and controlled laboratory tests, are reasonably acceptable. The proposed parameter identification technique offers a viable alternative data interpretation procedure for deducing pertinent Smith model parameters used frequently in pile driving analysis.

抄録全体を表示

It has been shown after mathematical and mechanical investigation that Limit Equilibrium Method (LEM) can be considered as a method to obtain the necessary condition of Slip Line Method (SLM), and that the solution can be obtained under the condition that F_s=1 and ∂F_s/∂θ=O, where F_s is the safety factor and θ is the inclination of the plane on which the safety factor is defined. Next, the generalized LEM (GLEM) is proposed, dealing with the following points : (1) Triangular or quadrangular blocks can be treated; (2) Safety factors are defined also on interblock planes; and (3) All types of plastic problems, slope stability, bearing capacity, and earth pressure are identically formulated. Two situations regarding treatment of the moment equilibrium condition are discussed. GLEM is applied to well-known problems. The results agree well with those obtained by theoretical methods. GLEM can be used to obtain the distribution of earth pressure or bearing capacity. GLEM, Iike ordinary LEM, is very effective for the practical problems, but GLEM is more theoretical and it can result in more accurate solutions.

抄録全体を表示

A comparative study of the static and dynamic response of a slope is carried out, using the large deformation theory of the updated Lagrangian formulation and the conventional infinitesimal theory. In the static analysis, a strength reduction method proposed by one of the authors is used to evaluate the safety factor of the slope. It is found that by the large deformation theory, the safety factor is larger than that calculated by the infinitesimal theory, and this difference becomes large along with the reduction of elastic modulus. In the dynamic analysis, it is observed that the large deformation theory gives smaller sliding displacement and larger response acceleration than the infinitesimal approach. It is concluded that in many cases the large deformation approach gives more adequate solutions.

抄録全体を表示