-
竹林 亜夫, 山本 和義, 泉谷 泰志, 上岡 真也
1999 年 9 巻 p.
1-8
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
In the mountain tunnel, the face stability is necessary until the support will confine the ground. However there were considerably many cases which fall into the accident construction by face's collapse. An unstable phenomenon including face's collapse is an important problem in the tunnel construction, it causes serious influence to the safety, delivery and cost etc. of the tunnel construction. We try to classify the unstable phenomenon experienced by the many tunnel constructions in our country, and consider the unstable phenomenon. We will propose the new countermeasure of the face stabilization by considering the ground conditions which trigger unstable face.
抄録全体を表示
-
鈴木 哲也, 疋田 貞良, 横山 博之, 宍戸 政仁
1999 年 9 巻 p.
9-14
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
On natural ground consisting of altered andesite lava and pyroclastic rock of the Neogene period of the Miocene epoch, two-dimensional resistivity method and VLF-EM survey were conducted in addition to seismic wave exploration using the refraction method - which is commonly used for. geological surveys in tunnels. Comparisons of the results of these surveys were made along with comparisons of these results with actual geological conditions found through pilot boring.
As a result, geological conditions which were noto clear with only the results of seismic wave exploration using the refraction method could be further elucidated by the other two method. It was also confirmed that the differences in geological conditions within the natural ground, such as the physical and mechanical properties of bedrock and subterranean water conditions, were well refracted in the contrast of the resistivity and seismic wave velocity in the natural ground. It was also through that different geological conditions within the natural ground were probably caused by mineral composition variations due to differences in the extent of past alteretions.
抄録全体を表示
-
木谷 日出男, 太田 岳洋, 江崎 哲郎, 蒋 宇静
1999 年 9 巻 p.
15-22
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
Stability of tunnel faces in sandy grounds is influenced by not only the mechanical properties of the ground but also groundwater conditions. Sand tank experiments have made clear that the morphological features of face collapse are influenced by the properties of grounds and the groundwater conditions. The simulations of the model experiment by a mechanical-groundwater flow coupling analysis are tried based on the finite-difference method, and it is verified that the analysis method is serviceable. The numerical parametric analyses are also carried out to understand the influences of the mechanical properties on face stability of tunnels in the water saturated sandy grounds. The results of the analyses indicated that the face stability decreases remarkably in condition of less than 80 percent in relative density of ground.
抄録全体を表示
-
清水 勉, 馬場 弘二, 塩月 隆久, 孫 建生, 今枝 良仁
1999 年 9 巻 p.
23-30
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
The linning concrete of Nikkureyama Tunnel at Jo-Shin-Etsu Highway has been reinforced by steel fiber concrete or carbon fiber sheets because of deformations of the tunnel at 400m of expanded mud stone area. However, many cracks were found at surfaces of steel fiber lining concrete near the carbon fiber sheets area. In this paper, the result of the investigation of cracks inside the lining concrete blinded by the carbon fiber sheets by the ultrasonic reflection sounding system are described.
抄録全体を表示
-
木梨 秀雄, 大内 一, 大西 有三
1999 年 9 巻 p.
31-38
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
The purpose of this study is to evaluate the bond properties of cable bolts based on bond stress distribution during pull-outs, and to clarify local bond stress - slip behavior for numerical models. Pullout tests of cable bolts have been conducted in laboratories, using varying levels of grout strength, confining stiffness, embedment length, grout thickness and the number of strands.
Results of the experiment have demonstrated that the cable bolt was pulled out rotationally along with the strand, and the bond strength, based on local bond distribution, did not rely on grout strength, confining stiffness, etc.
Using the bond parameters of Sbond and Kbond that were obtained from the experiment, we have simulated the result of a field pull-out test by UDEC. Results of the analysis have indicated that the axial force distribution coincides with the results of the field measurement.
抄録全体を表示
-
運上 茂樹, 星隈 順一, 小木曽 繁, 廣瀬 昌俊, 鈴木 猛康
1999 年 9 巻 p.
39-46
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
The seismic isolation for underground structures is the system in which a tunnel body is covered by a thin isolation layer consisting of elastic rubber with low shear modulus. It was applied for the first time to a shield-driven tunnel used as a common duct at a junction with a vertical shaft. In order to verify shearing capability of the newly formed isolation structure, an in-situ test was conducted right after its construction. The shear resistence of the isolation layer due to lateral movement of a tunnel body including a shield machine was measured when the tunnel body was pushed toward the cutting face by oil jacks fixed at the shaft wall. As a result, the relationship between reaction force and deformation for the isolation layer revealed that the isolation layer with necessary shear modulus and shearing capability was successfully formed.
抄録全体を表示
-
石井 昌次, 金子 研一, 杉山 雅彦
1999 年 9 巻 p.
47-54
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
The length of shield tunneling has been on the increasei nrecent years, and long-distancetunneling with a large-section shield exceeding 10 mindiameter is likely to increase inthe near future. Taking advantage of the fact that a large cross section is involved, the auth ors have developed an eccentric multi-axis shield tunneling machine that has six fan-shaped cutters. Each cutter has its own drive system and is capable of being retracted into a housing that has the same shape as the cutterhead located in the shield.
This paper reports on a three-dimensional flow analysis of slurry in the chamber and shows that use of segmental cutters improves flow.
抄録全体を表示
-
小泉 淳, 佐合 純造, 清水 幸範, 白井 孝典
1999 年 9 巻 p.
55-62
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
In recent years, a lot of underground rivers and ponds are constructed for the purpose of flood control by the shield tunneling method in urban areas such as Tokyo and Osaka. These tunnels and ponds are subjected to not only the earth pressure and water pressure from the outside of them but also the high water pressure from the inside of them. There are many problems that should be clear for getting the good tunnel. For example, what sort of structures of the tunnel lining is better and what sort of the design method of the tunnel lining is more rational. In this paper, the behavior of the primary lining and the secondary lining and the behavior of the inner water pressure are clarified from the results of simplified model test and their analytical investigations. As a result, the analyical model by which is reasonably able to explain the behavior of the shield tunnel subjected to the inner water pressure is shown. Moreover the rational structure and the design method of the tunnel tinning is proposed.
抄録全体を表示
-
神田 大, 小泉 淳
1999 年 9 巻 p.
63-70
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
Because of the lack of the fundamental test data, the current design method of liner plate structures depends on the impracticable or only theoretical calculation. Therefore there exists some differences in their point of view between each makers. Accordingly, the design method needs to be standardized. This study refers to several loading tests and analyses of liner plates and their structures. Their available ratios of bending stiffness are attempted to reveal by the tests. Consequently, the Beam-Spring Model can simulate the behavior of structures of liner plates in a good accuracy.
抄録全体を表示
-
瀬谷 正巳, 山本 松生, 篠川 俊夫, 小松 正三, 大田原 孝一
1999 年 9 巻 p.
71-76
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
We have applied three methods of geological survey to grasp fracture zone in tunnel under construction, and compared the results of survey methods each other. The survey methods are 1) High resolution seismic refraction method, 2) Horizontal core boring, 3) TSP (Tunnel Seismic Prediction) system. In High resolution seismic refraction method, more accurate distribution map of elastic wave velocities is obtained as compared with conventional seismic refraction method, and the location of fracture zone can be estimated from the results. In TSP system, estimated location and width of fracture zone are nearly equal to the results of horizontal core boring.
抄録全体を表示
-
笠 博義, 今井 久, 清水 学, 水端 八朗, 越野 洋一
1999 年 9 巻 p.
77-82
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
Spring water in tunnel have an influence on tunneling. Some investigation and analysis were carried on to estimate the quantity of spring water and to forecast the locality have large underground water, on the escape tunnel of Hakamagoshi Tunnel which was excavated by TBM.
The result of this study were as follows.
1) The quantity of water spring in tunnel over the whole tunnel was estimated by statistical analysis of the water quantity date on excavated section of the tunnel.
2) The locality which have large underground water were forecast by geological data.
3) A changing of water quantity was evaluated by chemical analysis of water.
抄録全体を表示
-
笹野 雅義, 力武 哲郎, 木村 正樹, 中垣 秀隆
1999 年 9 巻 p.
83-88
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
Tunnel support patterns is decided by a geological condition which is estimated by geological survey and these support patterns are change based on the results of cutting face observation and tunnel monitoring at tunnel construction. The authors applied the new system of rock mass classifications which JH made to some tunnel and compared the rock mass classification proposed by this system with the results of electric prospecting, blasting powder volume, and so on. Consequently it is showned that this new system is also very useful in the stage of geological survey and reduces the differences between the designed and adopted support patterns.
抄録全体を表示
-
吉塚 守, 伊藤 哲男, 城間 博通
1999 年 9 巻 p.
89-94
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
As numerical models to take discontinuity of rock mass into account, the finite element method with joint elements (assuming infinitesimal deformation), finite difference dynamic discontinuum analysis in which motion equation is solved in order to deal with the large deformation problem, and other methods have been developed.
This report presents the outline of investigation on the field application of the numerical method to the tunnel support design, by means of comparing the results of discontinuum analysis and measured field data, as one method to design the rational support structure of large cross section tunnel in New Toumei-Meisin Expressway.
抄録全体を表示
-
桜井 春輔, 藤村 三喜男, 原田 浩史, 岩野 政浩, 加藤 隆
1999 年 9 巻 p.
95-100
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
In this study, a new form of back analysis procedure has been applied to the shallow large tunnel project to decide the appropriate support system and to evaluate the safety of a tunnel. By using this procedure, the unknowns including in-situ stress, Young's modulus, and arbitrary non-elastic strains occurring in a surrounding ground due to the tunnel excavation can be back-calculated efficiently and accurately.
抄録全体を表示
-
寺本 正, 小池 武, 田村 武
1999 年 9 巻 p.
101-106
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
The structural analysis was carried out to investigate the behavior of damaged tunnel concrete lining reinforced by steel plate. Steel plate is thin compared with existing concrete lining, then the effect of such plate is not yet made clear. Computer analysis by finite element method (FEM) was executed including surrounding ground, so that the interaction between tunnel lining and ground can be considered.
Assumed damaged concrete lining types were hinged condition and lack of lining at tunnel top section. Under such damaged conditions, effect of steel plate thickness was studied. As a result, thin steel plate is sufficient under the condition of tying steel plate with damaged concrete lining.
抄録全体を表示
-
稲葉 秀雄, 鈴木 雅行, 多宝 徹
1999 年 9 巻 p.
107-112
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
A tunnel which has been constructed in “Shirasu”, met with impervious layer at 260 meter from entrance. We observed groundwater level 20 meter higher than spring line in opposite side of the that layer, and we needed more than one month to drawdown. Therefore we conducted a drawdown simulation with finite element method to understand an effective dewatering method.
The results of simulation are as follows:(1) It's effective on drawdown to use longer drainage borings togetherwell point drainage.(2) The specific storage of Shirasu is about 0.03l/m, and it's very important factor in this case.
抄録全体を表示
-
伊藤 隆, 越智 修, 小山 昭, 中川 信男, 重田 佳幸
1999 年 9 巻 p.
113-118
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
Generally, the shallow-depth tunnel is constructed by an auxiliary method. It is thought that especially an Umbrella Method and Pre-Lining Method is effective in control of surface settlement, the improvement in face stability.
Evaluating surface settlement control effect quantitative on Umbrella Method and Pre-Lining is presented. Considering simulation related with measurement value on surface settlement, a new design method of Umbrella Method and Pre-Lining Method is proposed. Simulation is calculated by 2-dimensional finite element method.
抄録全体を表示
-
武田 幸博, 西山 智夫, 藤本 孝晴, 小川 逸作, 松田 康治
1999 年 9 巻 p.
119-124
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
About 20 km length of the Kyushu Shinkansen route passes through on pumice-flow deposit Shirasu area in Kagoshima prefecture. The tunnel sections which total length is about 7 km are proposed in the Shirasu under the groundwater. Since few, Shirasu tunnels for railroad under the groundwater have constructed in Japan, design and construction method of the Shirasu tunnels should be developed.
This paper introduces ground improvement method with blast-furnace slag to construct permanent permeable roadbed for the Shirasu tunnels. It is expected that the Shirasu tunnels can be constructed safely and economically by using this method.
抄録全体を表示
-
尾嵜 師成, 山田 浩幸, 川北 眞嗣, 真柄 鎮, 小林 康範
1999 年 9 巻 p.
125-130
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
This paper shows the decision making and the planing of the vertical forepoling bolt method in auxiliary methods for tunneling under thin overburden with unsymmetrical earth pressure. Auxiliary methods are applied to avoid the ground settlement, collapse at the cutting face and landslide. It is important to decide proper supporting at the site with imperfect arch action or low bedrock strength such as tunnel portal or shallow overburden. As a guide to control those problems, the vertical forepoling mechanism is evaluated through the monitoring system for slope stability by using back analysis with field measurement data in this paper.
抄録全体を表示
-
河野 興, 藤井 英雄, 小泉 直人, 枩沢 俊夫, 田口 琢也
1999 年 9 巻 p.
131-136
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
A Low-Cohesion (Bulk Emulsion) Explosive complying to relevant laws and regulation in Japan is developed. Demonstration tests are carried out to prove its facility for handling and its blasting performance in actual construction site. Several useful-results were obtained from the tests, in relation to, 1) mechanical charge of explosion, 2) compact charge, 3) water-resisting qualities, 4) large burden-distance for blastholes, 5) reduction of charge-time and so on.
抄録全体を表示
-
大久保 雅憲, 日根 幸雄, 中川 浩二
1999 年 9 巻 p.
137-142
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
The tunnel support designed before the excavation often differs from the actual support. In this study the trends of the tunnel design of engineers (owners, geologists, consultants and construction engineers) were studied. At the first step, engineers picked up their concerning points in the design following to a geological survey reports. With the field observation, they modified their concerning points and gave the support design along the tu, nnel. After the circulating all available mutual data, members gave their final support design. The results were discussed from the point of human dependence on tunnel design.
抄録全体を表示
-
鈴木 正彦, 真下 英人, 高根 努, 藤井 邦男
1999 年 9 巻 p.
143-148
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
The effect of rockbolt on the ground stability around a tunnel in sandy and shallow overburden ground was not clarified, and the appropriate length and arrangement of them should be established.
Centrifugal model test using rockbolt was carried out, and the results on the effect of the rockbolt were acquired as follows:
(1) Placing in the part near crown was most effective, and in the part of wall was no effect.
(2) In placing many rockbolt, the length could be shortened to keep crown stable.
(3) In placing long rockbolt, the density of them could be sparse.
抄録全体を表示
-
城間 博通, 赤木 渉, 団 昭博, 山口 聡也, 斉藤 正幸
1999 年 9 巻 p.
149-154
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
Japan Highway Public Corporation has a plan to use reinforced concrete lining in collapse-prone sections of a long tunnel to be excavated with a full-section TBM for two lanes. The lining for the TBM will be manufactured on the site. In order to save in-situ processing and assembly of reinforcement for higher productivity, adoption of steel fiber reinforced concrete was studied. As a result, the lining made of steel fiber reinforced concrete have proved safe under expected loads.
抄録全体を表示
-
伊藤 隆, 越智 修, 小山 昭, 長谷川 達也, 永田 章
1999 年 9 巻 p.
155-160
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
In the tunnel located in squeezing ground, convergence of displacement may not be completed, before constructing secondary lining. For this reason, load may act on lining, after constructing secondary lining. In such a case, the design method which does not exceed the proof stress of secondary lining is required. At present, the method by frame analysis is widely used for the design method of secondary lining. In this report, we prepared the nomogram without performing frame analysis, and examined the applicability to design.
抄録全体を表示
-
砂金 伸治, 真下 英人
1999 年 9 巻 p.
161-166
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
Tunnel lining is designed and constructed mainly based on the past experience. Considering mechanical characteristic and the introduction of new materials to lining lead to a proper structure, and it can reduce the cost of construction. In this study, full-scale loading experiment for tunnel lining was carried out to achieve the upper purposes, and the analysis was done on the basis of the results. The following results were acquired:(1) the cracks were dispersed in the forecasting area in the lining with SFRC, (2) in analysis, the bending moment decreased considering the influence of crack in lining, while the axial force was nearly constant in the same load.
抄録全体を表示
-
山本 拓治, 北本 幸義, 伊達 健介, 岡本 道孝
1999 年 9 巻 p.
167-172
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
With regard to the current practice of tunnelling construction for railways and roads it is desired that a more practical method be developed so as to save time and cost as well as more safety. Lecentry, long forepiling method has been used widely so that the tunnel crown settlement in soil ground, can be restrained. On the other hand, cost by such method is generally high in case special technique or machine must be adopted. In addition, the effect by reinforcement using forepiling method is difficult to be made clear theoretically.
We developed a new forepiling method using middle length steel gas pipes for the purpose of lowering the construction cost with enough reinforcement effect. These reinforcement can be easily installed by conventional tunnelling machine. This paper reports the technical features and construction procedure. Next, the practical measuring results are shown. As a result, it is proved that the new forepiling method is effective in cost and reinforcement.
抄録全体を表示
-
海瀬 忍, 城間 博通, 三谷 浩二
1999 年 9 巻 p.
173-176
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
In the construction of tunnels with a large and flat cross section on the New Tomei-Meishin Expressways, high-strength concrete is considered to be an expected material for the secondary lining in order to achieve cost reduction by reducing both thickness of the lining and excavation area. For the purpose of finding important points in casting the high-strength concrete and it's strength characteristics with various conditions of casting and mix proportion, we performed testing by using model forms which simulate the real tunnel lining form and did the test construction in the field.
抄録全体を表示
-
杉浦 高広, 中井 健司, 佐藤 京, 西村 克弘, 三上 隆
1999 年 9 巻 p.
177-182
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
According to manuals on countermeasures against deformed tunnels, the cracks of secondary lining around the crown, are induced by uneven pressure and immersion of legs of supports. To investigate the cause of these cracks, questionnaires were gathered on the situation of the lining with cracks. Subsequently, it is found that the cracks tend to occur in sections near tunnel entrances employing no reinforcement, and constructed in cold season. A thermal stress analysis was also performed considering of support loads and measurement results on concrete stress. The result showed that it is possible for thermal stress and drying shrinkage to produce the cracks.
抄録全体を表示
-
北田 正彦, 林田 清高, 櫻井 春輔, 進士 正人, 木村 正樹
1999 年 9 巻 p.
183-188
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
Dramatic traffic increase in modern day necessitated an extension of cross section of Tennozan tunnel, which was constructed by a side drift method 35 years ago, in a very difficult ground condition. Knowing that the initial construction had experienced large deformation and high pressure on concrete lining, a special care was taken for planning and selection of construction method. As a result of the actual extension of the tunnel cross section was completed only with minor deformation with fair confidence in tunnel stability. Displacement recorded for a ordinary section was less than 1mm at the depth of 2m and at most 3mm at surface. That recorded for an extended section, however, went up to 2-3 mm at the depth of 4-5m, and was 10-14mm at surface on the right side.
抄録全体を表示
-
角南 明彦, 横山 和昭, 西村 誠一, 木村 正樹, 鳥居 敏
1999 年 9 巻 p.
189-194
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
TENNNOZAN TUNNEL were constructed as two lane highway tunnels 35years ago. An extension of cross section was planned because of modern traffic increase. The initial construction had experienced large deformation and high pressure on concrete lining due to landslides in the west portal. On the actual extension, the collapse of sand layer and large deformation of old tunnel lining occurred. It was clarified that this large deformation is due to loosening of sand layers by excavation and successive stress redistribution in fault zone. Finally, the Authors adopted AGF method as a countermeasure and completed the extension of cross section.
抄録全体を表示
-
篠川 俊夫, 金内 昌直, 山本 松生, 古川 哲男, 今藤 純朗
1999 年 9 巻 p.
195-200
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
TBM wall image processing system has been developed to take tunnel wall images by ccd cameras during TBM excavation and to analyze the geological structure of the tunnel using the images. The ccd cameras are fixed to the TBM machine, and tunnel wall surface is photographed continuously with the strokes of thrust jacks. Tunnel wall images will be combined and translated in a personal computer, and image maps will be printed out. Then, strike, dip and aperture of discontinuities are calculated by the geological analysis program. By applying this system to TBM excavation, the geological condition of tunnel wall can be grasped visually and the stability of tunnel under the influence of discontinuities can be estimated accurately. This system is applied to TBM pilot tunnel of Hamamatsu Tunnel East, Second Tomei Expressway, and satisfactory results are obtained.
抄録全体を表示
-
竹内 啓五, 和田 孝史, 泉谷 泰志, 宮下 国一郎, 厨川 弘樹
1999 年 9 巻 p.
201-206
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
In this paper we propose a new method for convergence measurement of tunnel. We achieve this using Electro-optical distance meter and Image processing technology. Image processing make possible to calculate correct point of target in tunnel automatically. And we can get 3-D information of target positions easily by personal computer. In experiment we verified possibilities of this method, and usefulness of user-interface of this system.
抄録全体を表示
-
橋本 正, 安田 亨, 市川 真治, 小嶋 勉, 長屋 淳一
1999 年 9 巻 p.
207-212
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
Large-scale facilities such as subway station, underground car park, underground passage road were investigated on design and construction technology for constructing using tunneling methods in the comparatively shallow space for the purpose of efficient use of underground space in urban area.
In this paper, the controversial point and the problem to be solved are reported to make a correct application of tunneling methods for large section tunnel with shallow overburden.
抄録全体を表示
-
東尾 啓司, 渡邊 和憲, 北村 正実, 内田 渉, 嶋村 貞夫
1999 年 9 巻 p.
213-218
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
It was found from researches on construction cases in Japan and overseas that one of the most effective tunneling methods for a large section tunnel with shallow overburden is installing the roof to stabilize the section against the overburden before excavating the ground. Examples for installation of tunnel-roof are connecting several small-section tunnels, which is common in China and France, utilizing a box-shield and combining shields by means of the shield-tunneling technology that is remarkably improved, and NATM.
In this paper, these tunneling methods are proposed and their effectiveness, advantage and disadvantage, applicability, and cost efficiency are reported.
抄録全体を表示
-
辻道 万也, 小林 秀紀
1999 年 9 巻 p.
219-224
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
Development of easy cleaning tiles for use of interior wall in tunnel was carried out. The adherent auto exhausts stains on newly developed tiles coated by silicate are found to be more easily washed out by water spraying than those on non-coated tiles. It was also found that the function of coated tiles was durable over the long term for various loads caused by the cleaning and the construction. This easy cleaning tile is expected to decrease the cost of the cleaning compared to the noncoated tiles and other conventional wall materials used in tunnel.
抄録全体を表示
-
須藤 敦史, 三上 隆, 岡田 正之
1999 年 9 巻 p.
225-230
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
This paper deals with an interpolation algorithm which using the stochastic method for design temperatures of heat insulator. The stochastic method is called “Semi-Variogram”, and we introduce a Semi-Variogram, how to interpolate for design temperatures of heat insulator. In this study, some experimental data of temperatures can be transformed to homogeneous spatial processes by means of some linear transformation. And, the interpolated design temperature from Semi-Variogram is compared with the observed temperatures of actual data. Finally, numerical examples are worked out to demonstrate the usefulness of this algorithm which is determined the design temperature for heat insulator in a planning load tunnel.
抄録全体を表示
-
岩本 勲, 笠井 克眞
1999 年 9 巻 p.
231-236
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
The design loads that are reduced by the ground reaction are estimated simply for usual conventional design method. The other hand, the reaction loads should be estimated by deformation and displacement of tunnel lining, for the beam-spring design method that is more practical than usual method. Our former report observed that the difference between the deformation mode of each design method have effect on the section force of tunnel lining at the certain soil condition. In this paper, the effects of ground condition on the ground reaction force and the section force of tunnel lining are discussed. They were revealed by analyzing the usual conventional design method and the beam-spring design method with the ground condition as the parameters.
抄録全体を表示
-
橿尾 恒治, 星野 高廣, 茄藤 勇, 鈴木 教之
1999 年 9 巻 p.
237-242
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
Subway Line No.12 will consist of Tokyo's first loop line, a 29-km-long route which will circle Tokyo from the departure point at the Shinjuku subcity center, and of an efferent arm extending approximately 14-km to the northwest of the metropolis.
In this section, Kuramae and Ryogoku Stations will be excavated by the cut-and-cover method, and a tunneling shield will he used to traverse the Sumida River and contact the two stations with parallel single-track tunnels.
In this paper, the driving control in extremely soft ground, on Sumidagawa Shield Line is reported.
抄録全体を表示
-
藤井 邦男, 真下 英人, 石村 利明, 真弓 英大
1999 年 9 巻 p.
243-248
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
The analysis by FEM is mainly used for the prediction method of ground movement in excavation by shield tunneling. It is necessary to set the analytical conditions, such as the models, the various values, and stress release ratio. But they are decided by each judgement in accordance with the sites and not by a certain concept. In this study to establish the prediction method of ground movement, the influence of the analytical condition to the result, analysis method and the proper settings of stress release ratio were examined by FEM using in-situ data in shield tunneling.
抄録全体を表示
-
猪熊 明, 田子島 充
1999 年 9 巻 p.
249-252
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
This paper discuss how we can determin the input data of shield-tunnel elastic FEM analysis. It especially focuses on stress release ratio, which might have something to do with tunnel diameter, not with overburden.
抄録全体を表示
-
施工順序の影響評価
永谷 英基, 笹倉 剛, 五十嵐 寛昌
1999 年 9 巻 p.
253-258
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
Recently, a new tunneling method, called Outer-shell-driven method, is spotlighted because it can produce large section effectively. Although Terzaghi's formula and total overburden pressure is widely used to design earth pressure in various conditions, they do not clarify the earth pressure mechanism under very closely constructed condition.
To make this point clear, authors have carried out series of centrifuge model tests using trap-door apparatus. An elasto-plastic finite element analysis also was carried out to simulate the centrifuge model test. Obtained results with respect to the application of the optimum construction order can be summarized as follows.
·As for the construction order for the case of very closely constructed 3 tunnels, earth pressure distribution is most stable (small) when the central tunnel is lastly excavated.
·An elasto-plastic finite element analysis with multi-yield surface model can give reasonable earth pressure estimation quantitatively.
抄録全体を表示
-
佐藤 寿延, 今田 徹
1999 年 9 巻 p.
259-264
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
Deep underground Utilization attracted much attention during Japan's “Bubble” economy in late 1980'. But the collapse of the bubble economy cooled down the momentum for deep underground utilization. However the number of uses of deep underground spaces are steadily increasing. The Provisional Investigation Committee for Deep Underground Utilization submitted its final report in 1998. Now the government is performing internal coordination to establish a legal system. This paper explains the correlation between legal system and technical subject.
抄録全体を表示
-
北澤 壮介, 田村 保, 松木田 正義, 高久 雅喜
1999 年 9 巻 p.
265-270
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
The result of feasibility study of the incremental launching method for construction of an immersed tunnel is described in this report. Incremental launching method was originally developed for the construction of bridges. Technical concept of this method is introduced to the construction of immersed tunnel underneath the fairway in the port. Technical issues are studied through the feasibility study on some immersed tunnel. The present study shows that this new method solves most of the construction problem for the conventional method in use and reduce the construction cost.
抄録全体を表示
-
有泉 毅, 岡留 孝一, 五十嵐 寛昌, 長屋 淳一
1999 年 9 巻 p.
271-276
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
It is known that the load acting on shield segments immediately after the segments are installed is not easy to be evaluated quantitatively nor to be modeled in the design of tunneling at the time being. In order to define quantitatively the earth pressure during tunneling, a real-scale model test is conducted. Based on the experimental results and the results from the in situ measurements. It is concluded that, the brush pressure from tail seal is rather small while, the load acting the segments during the tail of shield is passing through, is dominated by the earth pressures from back-filling or grease, and sometime may results in a large deviatoric earth pressure according to the tunneling condition.
抄録全体を表示
-
有泉 毅, 岡留 孝一, 長屋 淳一
1999 年 9 巻 p.
277-282
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
In order to evaluate the load acting on segments based on in-situ measurements, it is necessary to understand the relation between the deformation of segments, the deformation of ground, the measured earth pressure and the geometry of the segments. Up to now, because of the difficulty to conduct an in-situ measurement on the ring deformation and the joint deformation of the segments, few researches about the ring deformation and the joint behavior during tunneling are reported. In this paper, the relation between the observed load and segment deformation is examined based on the data measured at the three sites.
Furthermore, the effect of jack strength under 3-dimensional stress condition of the segments is investigated based on the data measured with the strain gauges installed on shield tunnelling segments.
抄録全体を表示
-
角田 治朗, 井上 正巳, 今井 和彦, 宮下 政樹, 長谷川 春生
1999 年 9 巻 p.
283-288
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
In this actuation system, a flexible maneuver of oil-pressure jack in transformed to rotary motion through crank system, and cutter is rotated. Moreover, by using oil-pressure jacks, maintenance is made easy and cost can be saved. In this experiment, it established that the revolution by the oil-pressure jacks is controlled with jack stroke. Telescopic motion of two or more jacks is overlapped and it its worked efficiently.
This results came from when it had arranged that the centerline of oil-pressure jack is not overlap, revolution torque was obtained efficiently and revolution of cutter is also stabilized was obtained as a result of this experiment.
抄録全体を表示
-
小西 真治, 新井 泰, 粥川 幸司, 津坂 治, 杉本 光隆
1999 年 9 巻 p.
289-294
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
Because of limited underground space due to jamming structures, it is required to construct tunnels in unprecedentedly deep underground or in shallow underground with the accurate shield control technique. Thus, it is necessary to adopt a technique based on a theoretical model in place of the conventional technique to construct tunnels. To verify the validity of the theoretical model, precise data on shield behaviors were obtained from two tunneling sites of rail way by a newly developed survey system. This paper reports to measuring results and factors of shield behavior. As results, the followings were made clear: 1) When the jack pattern was changed frequently, the shield behavior obtained by the newly developed survey system had higher accuracy, compared with the shield behavior obtained by the conventional system. 2) When segments were erected on a curve section, the change of direction angle during advance returned to half due to the loss of jack moments, the copy cutter effect and the ground condition.
抄録全体を表示
-
みなとみらい21線MM, 大岡川シールドT1工事 (上り線)
木村 光夫, 竹津 英二, 小林 啓一, 石田 修, 畑野 真仁
1999 年 9 巻 p.
295-300
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
“Minato-Mirai 21 Line” is a new subway line, constructed by Japan Railway Construction Public Corporation. It has 4.2 kilo-meters long, from Yokohama-station to (a provisional name) Motomachiterminal. This document shows tunnelling method applied at Oookagawa shield tunnel (564meters), passes under Yokohama-Port, in the middle of “Minato-Mirai 21 Line”.
Tunnel specification of this site is 7100 milli-meters diameter in parallel single line, tunnelling with high density slurry shield. Lining specification is “CONEX” segment as the first site in Japan, introduced techni que from Au stria in upper line, and Tenoned segment as the largest diameter tunnel with this type of lining in Japan, manufactured by Korea in down line.
This document shows tunnel behavior of boltless segment, verifications of degisn method propriety, and confirmation of tunnel lin g safety, about “CONEX” segment, with an alizing site measurement of selected section in this site.
抄録全体を表示
-
大野 宏紀, 小山 幸則, 西尾 誠高, 粥川 幸司
1999 年 9 巻 p.
301-306
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
Roppongi station in Metropolitan Subway Route No.12 was constructed as vertical twin tunnels. The lining structure used this shield method is formed out of specific segments. We executed the field measurement concerning the lining structure. In this measurement, we chiefly paid attention to grasp the following, 1, earth pressure for the lining structure. 2, influence of the lower tunnel on the upper shield excavation. 3, influence on lining structure when the temporary pillars were removed. As a result of the measurement, it was confirmed that this lining structure was safe concerning the behavior. In this paper, the result of the field measurement was described.
抄録全体を表示
-
千代 啓三, 田代 昇, 岡本 達也, 木戸 義和
1999 年 9 巻 p.
307-312
発行日: 1999/11/30
公開日: 2011/06/27
ジャーナル
フリー
One way to reduce the cost and duration of shield tunneling work is to eliminate the process of secondary lining. Despite various attempts, however, practical effective joints are not yet widely used. To develop an “Auto-Chuck segment” that can provide the primary tensile force, offers mechanical properties and high-speed assembly equivalent to conventional bolted joints, and contains all the joint members inside, the authors studied the strength performance of joint sections.
抄録全体を表示