電気加工学会誌

単発放電による放電加工の基礎的研究

工具電極先端形状と放電電圧波形および加工特性

土屋八郎, 後藤英和, 和宮崎真

1988 年 22 巻 43 号 p. 1-6
発行日: 1988/11/20
公開日: 2010/03/12

DOIhttps://doi.org/10.2526/jseme.22.1

ジャーナルフリー

抄録を表示する抄録を非表示にする

This paper deals with the machining characteristics in impulse discharge as a basic study on electrical discharge machining, Using model electrodes with various pointed end shapes, the gap voltage, discharge current, discharge energy, and the shape and volume of the discharged crater are measured. On the basis of these measured results, the effect of the pointed end shape of electrode on machining characteristics is discussed. The results obtained are as follows:
1) The gap voltage is not constant during discharge but varies depending on the pointed end shape of the electrode.
2) As the sharpness of the pointed end of the electrode increases, the diameter and the depth of the discharged crater become larger and deeper, and the volume of the discharged crater becomes larger.

抄録全体を表示

PDF形式でダウンロード (2920K)
電解複合砥粒加工作用に関する研究 (第1報)

チタンによる電解複合加工作用の検討

釜田浩, 木本康雄, 河合裕一, 垣野義昭

1988 年 22 巻 43 号 p. 7-17
発行日: 1988/11/20
公開日: 2010/03/12

DOIhttps://doi.org/10.2526/jseme.22.7

ジャーナルフリー

抄録を表示する抄録を非表示にする

Titanium has the properties of hard metal such as stainless steel and light metal such as aluminium. But it is difficult to get the mirror surface with high shape accuracy, because that the thermal conductivity of titanium is inferior to other metals. Especially, it is impossible to get wide-area mirror surface by using the ordinary working method such as cutting or grinding.
The authors succeed to get the mirror surface by means of the electrolytic-abrasive combined machining. In this paper, the authors describe both of the electrolytic and working characteristics in aqueous solution of NaNO₃ or NaCl and analytical experiments of combined working mechanism.

抄録全体を表示

PDF形式でダウンロード (2283K)
対電極法による形彫り放電加工面の電解仕上げ

酒井茂紀, 増沢隆久, 伊藤伸

1988 年 22 巻 43 号 p. 18-28
発行日: 1988/11/20
公開日: 2010/03/12

DOIhttps://doi.org/10.2526/jseme.22.18

ジャーナルフリー

抄録を表示する抄録を非表示にする

As reported before, WEDM products can be quickly finished until mirror-like by ECM using the remainder part of the products as the electrode. This report concerns with the extended application of that method to the products of EDM sinking. Since it is often difficult to realize a uniform flow of the electrolyte in this applications, the system was designed as; 1) The electrochemical process takes place in a still electrolyte. 2) The flushing is achieved by the periodical lift-up of the electrode and the synchronized spray of the electrolyte.
The experimental results show the effectiveness of this method in the production of cavities including forging dies, injection moulds etc.

抄録全体を表示

PDF形式でダウンロード (4448K)

J-STAGEへの登録はこちら（無料）