This paper proposes a single coil active shielding method of wireless unmanned aerial vehicle charger for leakage magnetic field reduction. A proposed shielding system eliminates the leakage magnetic field generated from the transmitting and receiving coils by generating the cancelling magnetic field. In order to enhance shielding effectiveness and preserve power transfer efficiency, shielding coil design parameters including radius and turns will analyze. Based on the analysis of coil design, shielding effectiveness and power transfer efficiency will estimate. In addition, shielding current control method corresponding to leakage magnetic field strength and phase will describe. A proposed shielding system has verified by simulations and experiments in terms of the total shielding effectiveness and power transfer efficiency measurements. The simulation and experimental results show that a proposed active shielding system has achieved 68.85% of average leakage magnetic field reduction with 1.92% of power transfer efficiency degradation. The shielding effectiveness and power transfer efficiency variation by coil design has been experimentally verified.

An effect of complex permeability of noise suppression sheets (NSS) on circuit parameters was investigated by a magnetic circuit analysis using cross-sectional size and material parameters. The series resistance and inductance of the coplanar waveguide (CPW) with a NSS considering the effect of the complex permeability of the NSS were quantitatively estimated. The result indicated that the imaginary and real part of the effective permeability affected the resistance and inductance, respectively. Furthermore, this analysis was applied to an 8-μm-wide CPW with a 0.5-μm-thick Co₈₅Zr₃Nb₁₂ film for quantitative estimation of the resistance, the inductance and the characteristic impedance. The estimated parameters were almost similar to the measured values. These results showed that the frequency characteristics of the circuit parameters could be controlled by changing size and material parameters.

This paper describes a method of measuring the unsymmetric voltage of conducted noise using a floating measurement system. Here, floating means that there is no physical connection to the reference ground. The method works by correcting the measured voltage to the desired unsymmetric voltage using the capacitance between the measurement instrument and the reference ground plane acting as the return path of the conducted electromagnetic noise. The existing capacitance measurement instrument needs a probe in contact with the ground, so it is difficult to use for on-site measurement of stray capacitance to ground at troubleshooting sites where the ground plane is not exposed or no ground connection point is available. The authors have developed a method of measuring stray capacitance to ground that does not require physical connection of the probe to the ground plane. The developed method can be used to estimate the capacitance between the measurement instrument and ground plane even if the distance and relative permittivity of the space are unknown. And a method is proposed for correcting the voltage measured with the floating measurement system to obtain the unsymmetric voltage of the noise by using the measured capacitance to ground. In the experiment, the unsymmetric voltage of a sinusoidal wave transmitting on a co-axial cable was measured with a floating oscilloscope in a shield room and the measured voltage was corrected to within 2dB of expected voltage by using the capacitance measured with the developed method. In addition, the voltage of a rectangular wave measured with the floating oscilloscope, which displays sag caused by the stray capacitance to ground, was corrected to a rectangular wave without sag. This means that the phase of the unsymmetric voltage can also be corrected by the measured stray capacitance. From these results, the effectiveness of the proposed methods is shown.

A method of determining emission limits was studied by using the amplitude probability distribution (APD) for low-probability pulsed electromagnetic disturbances due to discharge. The features of this method are 1) without using the previously reported relationship between APD and bit error rate, the limits are derived using the measured impact of a pulsed disturbance on various wireless communication systems having different bandwidths, and 2) disturbances caused by discharge with poor reproducibility are simulated by regularly repeated pulse-modulated sine waves to enable stable evaluation of the communication quality. APD-based limits are determined from the pulse repetition frequency of the simulated disturbance such that the block error rate (BLER) is less than a certain limit in wireless systems that are most sensitive to the pulsed disturbance. In the international standard CISPR 32 regulating electromagnetic disturbance, radiated disturbance due to discharge is excluded from the application of peak detection limits because of its low occurrence probability. In this paper we quantitatively determine appropriate criteria of the probability for the exclusion. Using the method, we measured the impact of low-probability pulsed interference on major wireless systems and found that GSM and Wi-Fi systems were the most sensitive. New APD-based limits were derived on the basis of these findings. The APD-based limits determined by the proposed method enable a valid evaluation of low-occurrence-probability pulsed disturbances without unconditionally excluding the measurement.

This paper presents a comparative loss analysis performed between an LLC converter and a phase-shift converter under the same size conditions using a power supply manufactured for information communications equipment. It is also shown herein that the LLC converter has a much higher ratio of transformer loss to total loss than the phase-shift converter and that the cause is the difference in the number of transformer turns between the two converters. Further, the ON-resistance of the secondary-side rectifier element and the number of transformer primary turns are shown to determine which of the two converters is superior in terms of low loss.

In wireless sensor networks (WSN), communication interference and the energy limitation of sensor nodes seriously hamper the network performance such as throughput and network lifetime. In this paper, we focus on the Successive Interference Cancellation (SIC) and Wireless Energy Transmission (WET) technology aiming to design a heuristic power control algorithm and an efficient cross-layer strategy to realize concurrency communication and improve the network throughput, channel utilization ratio and network lifetime. We realize that the challenge of this problem is that joint consideration of communication interference and energy shortage makes the problem model more complicated. To solve the problem efficiently, we adopt link scheduling strategy, time-slice scheduling scheme and energy consumption optimization protocol to construct a cross-layer optimization problem, then use an approximate linearization method to transform it into a linear problem which yields identical optimal value and solve it to obtain the optimal work strategy of wireless charging equipment (WCE). Simulation results show that adopting SIC and WCE can greatly improve communication capability and channel utilization ratio, and increase throughput by 200% to 500% while prolonging the network lifetime.

Connecting a large number of servers with high bandwidth links is one of the most crucial and challenging tasks that the Data Center Network (DCN) must fulfill. DCN faces a lot of difficulties like the effective exploitation of DC components that, if highlighted, can aid in constructing high performance, scalable, reliable, and cost-effective DCN. In this paper, we investigate the server-centric structure. We observe that current DCs use servers that mostly come with dual ports. Effective exploitation of the ports of interest for building the topology structure can help in realizing the potentialities of reducing expensive topology. Our new network topology, named “Parallel Cubes” (PCube), is a duplicate defined structure that utilizes the ports in the servers and mini-switches to form a highly effective, scalable, and efficient network structure. P-Cube provides high performance in network latency and throughput and fault tolerance. Additionally, P-Cube is highly scalable to encompass hundreds of thousands of servers with a low stable diameter and high bisection width. We design a routing algorithm for P-Cube network that utilizes the P-Cube structure to strike a balance among the numerous links in the network. Finally, numerical results are provided to show that our proposed topology is a promising structure as it outperforms other topologies and it is superior to Fat-tree, BCube and DCell by approximately 24%, 16%, 8% respectively in terms of network throughput and latency. Moreover, P-Cube extremely outperforms Fat-tree, and BCube structures in terms of total cost, complexity of cabling and power consumption.

In the age of big data, recommendation systems provide users with fast access to interesting information, resulting to a significant commercial value. However, the extreme sparseness of user assessment data is one of the key factors that lead to the poor performance of recommendation algorithms. To address this problem, we propose a spectral clustering recommendation scheme with low-rank matrix completion and spectral clustering. Our scheme exploits spectral clustering to achieve the division of a similar user group. Meanwhile, the low-rank matrix completion is used to effectively predict un-rated items in the sub-matrix of the spectral clustering. With the real dataset experiment, the results show that our proposed scheme can effectively improve the prediction accuracy of un-rated items.

The sidelobe level at tilts around 30-40 degrees in both the E and H planes due to a tapered excitation of units of 2×2 radiation slots is suppressed by introducing slit layers over a corporate-feed waveguide slot array antenna. The slit layers act as averaging the excitation of the adjacent radiating slots for sidelobe suppression in both planes. A 16×16-element array in the 70GHz band is fabricated. At the design frequency, the sidelobe levels at tilts around 30-40 degrees are suppressed from -25.4dB to -31.3dB in the E-plane and from -27.1dB to -38.9dB in the H-plane simultaneously as confirmed by measurements. They are suppressed over the desired range of 71.0-76.0GHz frequencies, compared to the conventional antenna.

Security in visible-light communication (VLC) has seen increasing importance in recent years. Asymmetrically clipped optical orthogonal frequency division multiplexing (ACO-OFDM) is recognized as one of the most powerful and efficient OFDM techniques. Therefore, it is well suited for use in both uplink and downlink connections. A security protocol based on this technique can facilitate secure uplink and downlink connections. In the present study, a low-complexity physical-layer key-generation encryption method is designed using the ACO-OFDM technique for indoor VLC networks. The security method is contingent on the generation of secret keys from the cyclic prefix OFDM samples positioned in the low-channel impact area to encrypt all signal frames before transmission, throughout the session. Numerical results indicate that the key-generation mechanism should be implemented during downlink data transmission throughout a session period to provide keys for both downlink and uplink connections. In this setup, the handset of the user employs the secret keys generated during downlink data transmission to encrypt its uplink transmission. This setup conserves the battery life of the handset. Additionally, the results indicate that the proposed security method can achieve a zero key mismatch rate with on-the-fly key creation.

For the blind estimation of short-code direct sequence spread spectrum (DSSS) signal pseudo-noise (PN) sequences, the eigenvalue decomposition (EVD) algorithm, the singular value decomposition (SVD) algorithm and the double-periodic projection approximation subspace tracking with deflation (DPASTd) algorithm are often used to estimate the PN sequence. However, when the asynchronous time delay is unknown, the largest eigenvalue and the second largest eigenvalue may be very close, resulting in the estimated largest eigenvector being any non-zero linear combination of the really required largest eigenvector and the really required second largest eigenvector. In other words, the estimated largest eigenvector exhibits unitary ambiguity. This degrades the performance of any algorithm estimating the PN sequence from the estimated largest eigenvector. To tackle this problem, this paper proposes a spreading sequence blind estimation algorithm based on the rotation matrix. First of all, the received signal is divided into two-information-period-length temporal vectors overlapped by one-information-period. The SVD or DPASTd algorithm can then be applied to obtain the largest eigenvector and the second largest eigenvector. The matrix composed of the largest eigenvector and the second largest eigenvector can be rotated by the rotation matrix to eliminate any unitary ambiguity. In this way, the best estimation of the PN sequence can be obtained. Simulation results show that the proposed algorithm not only solves the problem of estimating the PN sequence when the largest eigenvalue and the second largest eigenvalue are close, but also performs well at low signal-to-noise ratio (SNR) values.

Wireless full duplex (FD) communication can double the point-to-point throughput. To fully realize the benefits of the FD technique in wireless local area networks (WLANs), it is important to design the medium access control (MAC) protocols for FD communications. In FD MAC protocols, when a node wins the channel contention and transmits a primary transmission, its destination node can start a secondary transmission triggered by the primary transmission. Each secondary transmitter transmits a data frame even if its backoff timer is not zero. However, the backoff scheme in the FD MAC protocols follows the conventional scheme based on the distributed coordination function (DCF). Therefore, the nodes with FD MAC initialize the contention window (CW) size to minimum CW (CW_min) after their successful secondary transmissions. Therefore, CW initialization in the FD MAC causes further collisions at stations (STAs), which degrades network throughput. This paper proposes a novel backoff scheme for FD MAC protocols. In the proposed scheme, the CW size and backoff timer are not initialized but kept the current value after secondary transmissions. The proposed scheme can mitigate frame collisions at STAs and increase FD-transmission opportunity in the network, and then enhance the throughput significantly. This paper presents comprehensive performance evaluation in simulations, including non-saturation and saturation conditions, and co-existence conditions with legacy half duplex (HD) STAs. For performance analysis, this paper establishes Markov-chain models for the proposed scheme. The analytical results show theoretically that the operation of the proposed scheme enhances network throughput. The simulation results and analytical results show the effectiveness of the proposed scheme.

In this paper, the artificial noise (AN)-aided multiple-input single-output (MISO) cognitive radio network with simultaneous wireless information and power transfer (SWIPT) is considered, in which the cognitive user adopts the power-splitting (PS) receiver architecture to simultaneously decode information and harvest energy. To support secure communication and facilitate energy harvesting, AN is transmitted with information signal at cognitive base station (CBS). The secrecy energy efficiency (SEE) maximization problem is formulated with the constraints of secrecy rate and harvested energy requirements as well as primary user's interference requirements. However, this challenging problem is non-convex due to the fractional objective function and the coupling between the optimization variables. For tackling the challenging problem, a double-layer iterative optimization algorithm is developed. Specifically, the outer layer invokes a one-dimension search algorithm for the newly introduced tight relaxation variable, while the inner one leverages the Dinkelbach method to make the fractional optimization problem more tractable. Furthermore, closed-form expressions for the power of information signal and AN are obtained. Numerical simulations are conducted to demonstrate the efficiency of our proposed algorithm and the advantages of AN in enhancing the SEE performance.

In this paper, we study a radio frequency (RF)-powered backscatter assisted cognitive radio network (CRN), where an eavesdropper exists. This network includes a primary transmitter, a pair of secondary transmitter and receiver, a friendly jammer and an eavesdropper. We assume that the secondary transmitter works in ambient backscatter (AmBack) mode and the friendly jammer works in harvest-then-transmit (HTT) mode, where the primary transmitter serves as energy source. To enhance the physical layer security of the secondary user, the friendly jammer uses its harvested energy from the primary transmitter to transmit jamming noise to the eavesdropper. Furthermore, for maximizing the secrecy rate of secondary user, the optimal time allocation including the energy harvesting and jamming noise transmission phases is obtained. Simulation results verify the superiority of the proposed scheme.

This paper proposes a computational complexity-reduced algorithm for an adaptive peak-to-average power ratio (PAPR) reduction method previously developed by members of our research group that uses the null space in a multiple-input multiple-output (MIMO) channel for MIMO-orthogonal frequency division multiplexing (OFDM) signals. The proposed algorithm is an extension of the peak cancellation (PC) signal-based method that has been mainly investigated for per-antenna PAPR reduction. This method adds the PC signal, which is designed so that the out-of-band radiation is removed/reduced, directly to the time-domain transmission signal at each antenna. The proposed method, referred to as PCCNC (PC with channel-null constraint), performs vector-level signal processing in the PC signal generation so that the PC signal is transmitted only to the null space in the MIMO channel. We investigate three methods to control the beamforming (BF) vector in the PC signal, which is a key factor in determining the achievable PAPR performance of the algorithm. Computer simulation results show that the proposed PCCNC achieves approximately the same throughput-vs.-PAPR performance as the previous method while dramatically reducing the required computational cost.

This paper investigates the performance of interleave division multiple access (IDMA)-based random access with various interference canceller structures in order to support massive machine-type communications (mMTC) in the fifth generation (5G) mobile communication system. To support massive connectivity in the uplink, a grant-free and contention-based multiple access scheme is essential to reduce the control signaling overhead and transmission latency. To suppress the packet loss due to collision and to achieve multi-packet reception, non-orthogonal multiple access (NOMA) with interference cancellation at the base station receiver is essential. We use IDMA and compare various interference canceller structures such as the parallel interference canceller (PIC), successive interference canceller (SIC), and their hybrid from the viewpoints of the error rate and decoding delay time. Based on extensive computer simulations, we show that IDMA-based random access is a promising scheme for supporting mMTC and the PIC-SIC hybrid achieves a good tradeoff between the error rate and decoding delay time.

Green cognitive radio (CR) plays an important role in offering secondary users (SUs) with more spectrum with smaller energy expenditure. However, the energy efficiency (EE) issues associated with green CR for fading channels have not been fully studied. In this paper, we investigate the average EE maximization problem for spectrum-sharing CR in fading channels. Unlike previous studies that considered either the peak or the average transmission power constraints, herein, we considered both of these constraints. Our aim is to maximize the average EE of SU by optimizing the transmission power under the joint peak and average transmit power constraints, the rate constraint of SU and the quality of service (QoS) constraint of primary user (PU). Specifically, the QoS for PU is guaranteed based on either the average interference power constraint or the PU outage constraint. To address the non-convex optimization problem, an iterative optimal power allocation algorithm that can tackle the problem efficiently is proposed. The optimal transmission powers are identified under both of perfect and imperfect channel side information (CSI). Simulations show that our proposed scheme can achieve higher EE over the existing scheme and the EE achieved under perfect CSI is better than that under imperfect CSI.