In this paper, we investigate the evolution of an optical network architecture and discuss the future direction of research on optical network design and control. We review existing research on optical network design and control and present some open challenges. One of the important open challenges lies in multilayer resource optimization including IT and optical network resources. We propose an adaptive joint optimization method of IT resources and optical spectrum under time-varying traffic demand in optical networks while avoiding an increase in operation cost. We formulate the problem as mixed integer linear programming and then quantitatively evaluate the trade-off relationship between the optimality of reconfiguration and operation cost. We demonstrate that we can achieve sufficient network performance through the adaptive joint optimization while suppressing an increase in operation cost.

The novel optical path routing architecture named flexible waveband routing networks is reviewed in this paper. The nodes adopt a two-stage path routing scheme where wavelength selective switches (WSSs) bundle optical paths and form a small number of path groups and then optical switches without wavelength selectivity route these groups to desired outputs. Substantial hardware scale reduction can be achieved as the scheme enables us to use small scale WSSs, and even more, share a WSS by multiple input cores/fibers through the use of spatially-joint-switching. Furthermore, path groups distributed over multiple bands can be switched by these optical switches and thus the adaptation to multi-band transmission is straightforward. Network-wide numerical simulations and transmission experiments that assume multi-band transmission demonstrate the validity of flexible waveband routing.

To cope with the drastic increase in traffic, space division multiplexing elastic optical networks (SDM-EONs) have been investigated. In multicore fiber environments that realize SDM-EONs, crosstalk (XT) occurs between optical paths transmitted in the same frequency slots of adjacent cores, and the quality of the optical paths is degraded by the mutual influence of XT. To solve this problem, we propose a core and spectrum assignment method that introduces the concept of prohibited frequency slots to protect the degraded optical paths. First-fit-based spectrum resource allocation algorithms, including our previous study, have the problem that only some frequency slots are used at low loads, and XT occurs even though sufficient frequency slots are available. In this study, we propose a core and spectrum assignment method that introduces the concepts of “adjacency criterion” and “XT budget” to suppress XT at low and middle loads without worsening the path blocking rate at high loads. We demonstrate the effectiveness of the proposed method in terms of the path blocking rate using computer simulations.

We propose a demodulation framework to extend the maximum distance of unrepeated transmission systems, where the simplest back propagation (BP), polarization and phase recovery, data arrangement for machine learning (ML), and symbol decision based on ML are rationally combined. The deterministic waveform distortion caused by fiber nonlinearity and chromatic dispersion is partially eliminated by BP whose calculation cost is minimized by adopting the single-step Fourier method in a pre-processing step. The non-deterministic waveform distortion, i.e., polarization and phase fluctuations, can be eliminated in a precise manner. Finally, the optimized ML model conducts the symbol decision under the influence of residual deterministic waveform distortion that cannot be cancelled by the simplest BP. Extensive numerical simulations confirm that a DP-16QAM signal can be transmitted over 240km of a standard single-mode fiber without optical repeaters. The maximum transmission distance is extended by 25km.

A city-level digital twin is a critical enabling technology to construct a smart city that helps improve citizens' living conditions and quality of life. Currently, research and development regarding the digital replica city are pursued worldwide. However, many research projects only focus on creating the 3D city model. A mechanism to involve key players, such as data providers, service providers, and application developers, is essential for constructing the digital replica city and producing various city applications. Based on this motivation, the authors of this paper are pursuing a research project, namely Decentralized Digital Twin EcoSystem (D2EcoSys), to create an ecosystem to advance (and self-grow) the digital replica city regarding time and space directions, city services, and values. This paper introduces an overview of the D2EcoSys project: vision, problem statement, and approach. In addition, the paper discusses the recent research results regarding networking technologies and demonstrates an early testbed built in the Kashiwa-no-ha smart city.

We evaluated the transmission performance, including received power and transmission throughput characteristics, in 4×4 single-user multiple-input multiple-output (SU-MIMO) transmission for synchronous time division duplex (TDD) and downlink data channels in comparison with single-input single-output (SISO) transmission in an environment where a local 5G wireless base station was installed on the roof of a research building at our university. Accordingly, for the received power characteristics, the difference between the simulation value, which was based on the ray tracing method, and the experimental value at 32 points in the area was within a maximum difference of approximately 10 dB, and sufficient compliance was obtained. Regarding the transmission throughput versus received power characteristics, after showing a simulation method for evaluating throughput characteristics in MIMO, we compared the results with experimental results. The cumulative distribution function (CDF) of the transmission throughput shows that, at a CDF of 50%, in SISO transmission, the simulated value is approximately 115Mbps, and the experimental value is 105Mbps, within a difference of approximately 10Mbps. By contrast, in MIMO transmission, the simulation value is 380Mbps, and the experimental value is approximately 420Mbps, which is a difference of approximately 40Mbps. It was shown that the received power and transmission throughput characteristics can be predicted with sufficient accuracy by obtaining the delay profile and the system model at each reception point using the both ray tracing and MIMO simulation methods in actual environments.

The fifth-generation (5G) new radio (NR) standard employs ultra-reliable and low-latency communication (URLLC) to provide real-time wireless interactive capability for the internet of things (IoT) applications. To satisfy the stringent latency and reliability demands of URLLC services, grant-free (GF) transmissions with the K-repetition transmission (K-Rep) have been introduced. However, fading fluctuations can negatively impact signal quality at the base station (BS), leading to an increase in the number of repetitions and raising concerns about interference and energy consumption for IoT user equipment (UE). To overcome these challenges, this paper proposes novel adaptive K-Rep control schemes that employ site diversity reception to enhance signal quality and reduce energy consumption. The performance evaluation demonstrates that the proposed adaptive K-Rep control schemes significantly improve communication reliability and reduce transmission energy consumption compared with the conventional K-Rep scheme, and then satisfy the URLLC requirements while reducing energy consumption.

Fifth generation mobile communication system (5G) mobile operators need to explore new use cases and/or applications together with vertical industries, the industries that are potential users of 5G, in order to fully exploit the new 5G capabilities in terms of its application. Vehicle-to-Everything (V2X) communications for platooning are considered to be one of new 5G use cases whose ultra reliable and low latency communication (URLLC) aspects are required. The authors build a field experimental environment, towards application to truck platooning, with actual large-size trucks and a prototype system, for 5G New Radio (NR) technology based V2X communications. Its most distinctive feature is that the 5G NR-V2X prototype system is equipped with UE-to-UE radio interface (i.e., sidelink) for V2V Direct communication, in addition to the traditional radio interfaces between BS and UE for V2N/V2N2V communications. This paper presents performance evaluation and demonstration of real-time vehicle control information exchange using over the sidelink of 5G NR-V2X prototype system for automated follower truck platooning. This paper evaluates the V2V Direct communication latency and reliability performance of the sidelink, and clarify 5G NR sidelink achieves lower peak of latency and higher packet reception rate in V2V Direct communication performance than an optical wireless communication system product. Then, it also introduces a 5G URLLC use case demonstration of automated follower truck platooning trial employed with the prototype system in a public expressway environment.

Information-Centric Networking (ICN) originally innovated for efficient data distribution, is currently discussed to be applied to edge computing environment. In this paper, we focus on a more flexible context, in-network computing, which is enabled by ICN architecture. In ICN-based in-network computing, a function chaining (routing) method for chaining multiple functions located at different routers widely distributed in the network is required. Our proposal is a twofold approach, On-demand Routing for Responsive Route (OR³) and Route Records (RR). OR³ efficiently chains data and multiple functions compared with an existing routing method. RR reactively stores routing information to reduce communication/computing overhead. In this paper, we conducted a mathematical analytics in order to verify the correctness of the proposed routing algorithm. Moreover, we investigate applicabilities of OR³/RR to an edge computing context in the future Beyond 5G/6G era, in which rich computing resources are provided by mobile nodes thanks to the cutting-edge mobile device technologies. In the mobile environments, the optimum from viewpoint of “routing” is largely different from the stable wired environment. We address this challenging issue and newly propose protocol enhancements for OR³ by considering node mobility. Evaluation results reveal that mobility-enhanced OR³ can discover stable paths for function chaining to enable more reliable ICN-based in-network computing under the highly-dynamic network environment.

To establish a network service in network functions virtualization (NFV) networks, the orchestrator addresses the challenge of service chaining and virtual network function placement (SC-VNFP) by mapping virtual network functions (VNFs) and virtual links onto physical nodes and links. Unlike traditional networks, network operators in NFV networks must contend with both hardware and software failures in order to ensure resilient network services, as NFV networks consist of physical nodes and software-based VNFs. To guarantee network service quality in NFV networks, the existing work has proposed an approach for the SC-VNFP problem that considers VNF diversity and redundancy. VNF diversity splits a single VNF into multiple lightweight replica instances that possess the same functionality as the original VNF, which are then executed in a distributed manner. VNF redundancy, on the other hand, deploys backup instances with standby mode on physical nodes to prepare for potential VNF failures. However, the existing approach does not adequately consider the tradeoff between resource efficiency and service availability in the context of VNF diversity and redundancy. In this paper, we formulate the SC-VNFP problem with VNF diversity and redundancy as a two-step integer linear program (ILP) that adjusts the balance between service availability and resource efficiency. Through numerical experiments, we demonstrate the fundamental characteristics of the proposed ILP, including the tradeoff between resource efficiency and service availability.

In the beyond 5G and 6G networks, the number of connected devices and their types will greatly increase including not only user devices such as smartphones but also the Internet of Things (IoT). Moreover, Non-terrestrial networks (NTN) introduce dynamic changes in the types of connected devices as base stations or access points are moving objects. Therefore, continuous network capacity design is required to fulfill the network requirements of each device. However, continuous optimization of network capacity design for each device within a short time span becomes difficult because of the heavy calculation amount. We introduce device types as groups of devices whose traffic characteristics resemble and optimize network capacity per device type for efficient network capacity design. This paper proposes a method to classify device types by analyzing only encrypted traffic behavior without using payload and packets of specific protocols. In the first stage, general device types, such as IoT and non-IoT, are classified by analyzing packet header statistics using machine learning. Then, in the second stage, connected devices classified as IoT in the first stage are classified into IoT device types, by analyzing a time series of traffic behavior using deep learning. We demonstrate that the proposed method classifies device types by analyzing traffic datasets and outperforms the existing IoT-only device classification methods in terms of the number of types and the accuracy. In addition, the proposed model performs comparable as a state-of-the-art model of traffic classification, ResNet 1D model. The proposed method is suitable to grasp device types in terms of traffic characteristics toward efficient network capacity design in networks where massive devices for various services are connected and the connected devices continuously change.

Compressed sensing is a rapidly growing research field in signal and image processing, machine learning, statistics, and systems control. In this survey paper, we provide a review of the theoretical foundations of compressed sensing and present state-of-the-art algorithms for solving the corresponding optimization problems. Additionally, we discuss several practical applications of compressed sensing, such as group testing, sparse system identification, and sparse feedback gain design, and demonstrate their effectiveness through Python programs. This survey paper aims to contribute to the advancement of compressed sensing research and its practical applications in various scientific disciplines.

Information-Centric Networking (ICN) is an innovative technology that provides low-loss, low-latency, high-throughput, and high-reliability communications for diversified and advanced services and applications. In this article, we present a technical survey of ICN functionalities such as in-network caching, routing, transport, and security mechanisms, as well as recent research findings. We focus on CCNx, which is a prominent ICN protocol whose message types are defined by the Internet Research Task Force. To facilitate the development of functional code and encourage application deployment, we introduce an open-source software platform called Cefore that facilitates CCNx-based communications. Cefore consists of networking components such as packet forwarding and in-network caching daemons, and it provides APIs and a Python wrapper program that enables users to easily develop CCNx applications for on Cefore. We introduce a Mininet-based Cefore emulator and lightweight Docker containers for running CCNx experiments on Cefore. In addition to exploring ICN features and implementations, we also consider promising research directions for further innovation.

In this paper, belief propagation (BP) multi-input multi-output (MIMO) detection with maximum ratio combining (MRC) and minimum mean square error (MMSE) pre-cancellation is proposed for overload MIMO. The proposed scheme applies MRC before MMSE pre-cancellation. The BP MIMO detection with MMSE pre-cancellation leads to a reduction in diversity gain due to the decreased number of connections between variable nodes and observation nodes in a factor graph. MRC increases the diversity gain and contributes to improve bit error rate (BER) performance. Numerical results obtained through computer simulation show that the BERs of the proposed BP MIMO detection with MRC and MMSE pre-cancellation yields bit error rates (BERs) that are approximately 0.5dB better than those of conventional BP MIMO detection with MMSE pre-cancellation at a BER of 10^-3.

Cross-domain data fusion is becoming a key driver in the growth of numerous and diverse applications in the Internet of Things (IoT) era. We have proposed the concept of a new information platform, Geo-Centric Information Platform (GCIP), that enables IoT data fusion based on geolocation, i.e., produces spatio-temporal content (STC), and then provides the STC to users. In this environment, users cannot know in advance “when,” “where,” or “what type” of STC is being generated because the type and timing of STC generation vary dynamically with the diversity of IoT data generated in each geographical area. This makes it difficult to directly search for a specific STC requested by the user using the content identifier (domain name of URI or content name). To solve this problem, a new content discovery method that does not directly specify content identifiers is needed while taking into account (1) spatial and (2) temporal constraints. In our previous study, we proposed a content discovery method that considers only spatial constraints and did not consider temporal constraints. This paper proposes a new content discovery method that matches user requests with content metadata (topic) characteristics while taking into account spatial and temporal constraints. Simulation results show that the proposed method successfully discovers appropriate STC in response to a user request.

Mobile edge computing (MEC) is a key technology for providing services that require low latency by migrating cloud functions to the network edge. The potential low quality of the wireless channel should be noted when mobile users with limited computing resources offload tasks to an MEC server. To improve the transmission reliability, it is necessary to perform resource allocation in an MEC server, taking into account the current channel quality and the resource contention. There are several works that take a deep reinforcement learning (DRL) approach to address such resource allocation. However, these approaches consider a fixed number of users offloading their tasks, and do not assume a situation where the number of users varies due to user mobility. This paper proposes Deep reinforcement learning model for MEC Resource Allocation with Dummy (DMRA-D), an online learning model that addresses the resource allocation in an MEC server under the situation where the number of users varies. By adopting dummy state/action, DMRA-D keeps the state/action representation. Therefore, DMRA-D can continue to learn one model regardless of variation in the number of users during the operation. Numerical results show that DMRA-D improves the success rate of task submission while continuing learning under the situation where the number of users varies.

Blockchain systems rely on peer-to-peer (P2P) overlay networks to propagate transactions and blocks. The node management of P2P networks affects the overall performance and reliability of the system. The traditional structure is based on random connectivity, which is known to be an inefficient operation. Therefore, we propose MSLT, a multiscale blockchain P2P network node management method to improve transaction performance. This approach involves configuring the network to operate at multiple scales, where blockchain nodes are grouped into different ranges at each scale. To minimize redundancy and manage traffic efficiently, neighboring nodes are selected from each range based on a predetermined set of rules. Additionally, a node updating method is implemented to improve the reliability of the network. Compared with existing transmission models in efficiency, utilization, and maximum transaction throughput, the MSLT node management model improves the data transmission performance.

This study investigates the improvement of the channel capacity of 5-GHz-band multiple-input multiple-output (MIMO) communication using microwave-guided modes propagating along a polyvinyl chloride (PVC) pipe wall for a buried pipe inspection robot. We design a planar Yagi-Uda antenna to reduce transmission losses in communication with PVC pipe walls as propagation paths. Coupling efficiency between the antenna and a PVC pipe is improved by attaching a PVC adapter with the same curvature as the PVC pipe's inner wall to the Yagi-Uda antenna to eliminate any gap between the antenna and the inner wall of the PVC pipe. The use of a planar Yagi-Uda antenna with a PVC adaptor decreases the transmission loss of a 5-GHz-band microwave signal propagating along a 1-m-lomg straight PVC pipe wall by 7dB compared to a dipole antenna. The channel capacity of a 2×2 MIMO system using planar Yagi-Uda antennas is more than twice that of the system using dipole antennas.

The proportion of persons over 65 years old is projected to increase worldwide between 2022 and 2050. The increasing burden on medical staff and the shortage of human resources are growing problems. Bedsores are injuries caused by prolonged pressure on the skin and stagnation of blood flow. The more the damage caused by bedsores progresses, the longer the treatment period becomes. Moreover, patients require surgery in some serious cases. Therefore, early detection is essential. In our research, we are developing a non-contact bedsore detection system using electromagnetic waves at 10.5GHz. In this paper, we extracted appropriate information from a scalogram and utilized it to detect the sizes of bedsores. In addition, experiments using a phantom were conducted to confirm the basic operation of the bedsore detection system. As a result, using the approximate curves and lines obtained from prior analysis data, it was possible to estimate the volume of each defected area, as well as combinations of the depth of the defected area and the length of the defected area. Moreover, the experiments showed that it was possible to detect bedsore presence and estimate their sizes, although the detection results had slight variations.

The application of millimeter wave (mmWave) directional transmission technology in high-speed railway (HSR) scenarios helps to achieve the goal of multiple gigabit data rates with low latency. However, due to the high mobility of trains, the traditional initial access (IA) scheme with high time consumption is difficult to guarantee the effectiveness of the beam alignment. In addition, the high path loss at the coverage edge of the millimeter wave remote radio unit (mmW-RRU) will also bring great challenges to the stability of IA performance. Fortunately, the train trajectory in HSR scenarios is periodic and regular. Moreover, the cell-free network helps to improve the system coverage performance. Based on these observations, this paper proposes an efficient IA scheme based on location and history information in cell-free networks, where the train can flexibly select a set of mmW-RRUs according to the received signal quality. We specifically analyze the collaborative IA process based on the exhaustive search and based on location and history information, derive expressions for IA success probability and delay, and perform the numerical analysis. The results show that the proposed scheme can significantly reduce the IA delay and effectively improve the stability of IA success probability.

Device-to-device (D2D) communication allows user terminals to directly communicate with each other without the need for any base stations (BSs). Since the D2D communication underlaying a cellular system shares frequency channels with BSs, co-channel interference may occur. Successive interference cancellation (SIC), which is also called the serial interference canceler, detects and subtracts user signals from received signals in descending order of received power, can cope with the above interference and has already been applied to fog nodes that manage communications among machine-to-machine (M2M) devices besides direct communications with BSs. When differences among received power levels of user signals are negligible, however, SIC cannot work well and thus causes degradation in bit error rate (BER) performance. To solve such a problem, this paper proposes to apply parallel interference cancellation (PIC), which can simultaneously detect both desired and interfering signals under the maximum likelihood criterion and can maintain good BER performance even when power level differences among users are small. When channel coding is employed, however, SIC can be superior to PIC in terms of BER under some channel conditions. Considering the superiority, this paper also proposes to select the proper cancellation scheme and modulation and coding scheme (MCS) that can maximize the throughput of D2D under a constraint of BER, in which the canceler selection is referred to as adaptive interference cancellation. Computer simulations show that PIC outperforms SIC under almost all channel conditions and thus the adaptive selection from PIC and SIC can achieve a marginal gain over PIC, while PIC can achieve 10% higher average system throughput than that of SIC. As for transmission delay time, it is demonstrated that the adaptive selection and PIC can shorten the delay time more than any other schemes, although the fog node causes the delay time of 1ms at least.

Orbital angular momentum (OAM) multiplexing technology is being investigated for high-capacity point-to-point (PtP) wireless transmission toward beyond 5G systems. OAM multiplexing is a spatial multiplexing technique that utilizes the twisting of electromagnetic waves. Its advantage is that it reduces the computational complexity of the signal processing on spatial multiplexing. Meanwhile point-to-multi point (PtMP) wireless transmission, such as integrated access and backhaul (IAB) will be expected to simultaneously accommodates a high-capacity prioritized backhaul-link and access-links. In this paper, we study the extension of OAM multiplexing transmission from PtP to PtMP to meet the above requirements. We propose a backhaul prioritized resource control algorithm that maximizes the received signal-to-interference and noise ratio (SINR) of the access-links while maintaining the backhaul-link. The proposed algorithm features adaptive mode selection that takes into account the difference in the received power of each OAM mode depending on the user equipment position and the guaranteed power allocation of the backhaul capacity. We then evaluate the performance of the proposed method through computer simulation. The results show that throughput of the access-links improved compared with the conventional multi-beam multi-user multi-input multi-output (MIMO) techniques while maintaining the throughput of the backhaul-link above the required value with minimal feedback information.

Analog beamforming with broadband large-scale antenna arrays in millimeter wave (mmWave) multiple input multiple output (MIMO) systems faces the beam squint problem. In this paper, we first investigate the sensitivity of analog beamforming to subarray spatial separations in wideband mmWave systems using hybrid arrays, and propose optimized subarray separations. We then design improved analog beamforming after phase compensation based on Zadoff-Chu (ZC) sequence to flatten the frequency response of radio frequency (RF) equivalent channel. Considering a single-carrier frequency-domain equalization (SC-FDE) scheme at the receiver, we derive low-complexity linear zero-forcing (ZF) and minimum mean squared error (MMSE) equalizers in terms of output signal-to-noise ratio (SNR) after equalization. Simulation results show that the improved analog beamforming can effectively remove frequency-selective deep fading caused by beam squint, and achieve better bit-error-rate performance compared with the conventional analog beamforming.

This paper proposes user equipment (UE) grouping schemes and evaluates the performance of a scheduling scheme for each formed group in collaborative multiple-input multiple-output (MIMO) reception. In previous research, the criterion for UE grouping and the effects of group scheduling has never been presented. In the UE grouping scheme, two criteria, the base station (BS)-oriented one and the UE-oriented one, are presented. The BS-oriented full search scheme achieves ideal performance though it requires knowledge of the relative positions of all UEs. Therefore, the UE-oriented local search scheme is also proposed. As the scheduling scheme, proportional fairness scheduling is used in resource allocation for each formed group. When the number of total UEs increases, the difference in the number of UEs among groups enlarges. Numerical results obtained through computer simulation show that the throughput per user increases and the fairness among users decreases when the number of UEs in a cell increases in the proposed schemes compared to those of the conventional scheme.

In this paper, we investigate optimal design of millimeter-wave (mmWave) multiuser line-of-sight multiple-input-multiple-output (LOS MIMO) systems using hybrid arrays of subarrays based on hybrid block diagonalization (BD) precoding and combining scheme. By introducing a general 3D geometric channel model, the optimal subarray separation products of the transmitter and receiver for maximizing sum-rate is designed in terms of two regular configurations of adjacent subarrays and interleaved subarrays for different users, respectively. We analyze the sensitivity of the optimal design parameters on performance in terms of a deviation factor, and derive expressions for the eigenvalues of the multiuser equivalent LOS MIMO channel matrix, which are also valid for non-optimal design. Simulation results show that the interleaved subarrays can support longer distance communication than the adjacent subarrays given the appropriate fixed subarray deployment.

In this paper, the quality and transferred data based video bitrate control method for web-conferencing services is proposed, aiming to reduce transferred data by suppressing excessive quality. In web-conferencing services, the video bitrate is generally controlled in accordance with the network conditions (e.g., jitter and packet loss rate) to improve users' quality. However, in such a control, the bitrate is excessively high when the network conditions is sufficiently high (e.g., high throughput and low jitter), which causes an increased transferred data volume. The increased volume of data transferred leads to increased operational costs, such as network costs for service providers. To solve this problem, we developed a method to control the video bitrate of each user to achieve the required quality determined by the service provider. This method is implemented in an actual web-conferencing system and evaluated under various conditions. It was shown that the bitrate could be controlled in accordance with the required quality to reduce the transferred data volume.