Journal of the Metal Finishing Society of Japan
Online ISSN : 1884-3395
Print ISSN : 0026-0614
ISSN-L : 0026-0614
Volume 10, Issue 9
Displaying 1-6 of 6 articles from this issue
  • [in Japanese]
    1959Volume 10Issue 9 Pages 323-328
    Published: September 20, 1959
    Released on J-STAGE: October 30, 2009
    JOURNAL FREE ACCESS
    Download PDF (853K)
  • [in Japanese]
    1959Volume 10Issue 9 Pages 328-331
    Published: September 20, 1959
    Released on J-STAGE: October 30, 2009
    JOURNAL FREE ACCESS
    Download PDF (1208K)
  • [in Japanese]
    1959Volume 10Issue 9 Pages 332-339
    Published: September 20, 1959
    Released on J-STAGE: October 30, 2009
    JOURNAL FREE ACCESS
    Download PDF (1135K)
  • [in Japanese]
    1959Volume 10Issue 9 Pages 340-349
    Published: September 20, 1959
    Released on J-STAGE: October 30, 2009
    JOURNAL FREE ACCESS
    Download PDF (3737K)
  • Masayoshi TAGAYA, Shigeteru ISA, Keizo ISHIDA, Takashi HADA
    1959Volume 10Issue 9 Pages 350-354
    Published: September 20, 1959
    Released on J-STAGE: October 30, 2009
    JOURNAL FREE ACCESS
    The high temperature oxidation protection for molybdenum by siliconizing, chromizing or Cr, Ni and Co electro-deposited coating, etc. was investigated and it was recognized that Cr and Ni double layer deposited coating was the most adequate among the oxidation protective coatings for molybdenum, but the oxidation resistance life of molybdenum at 1000°C in air obtained by this coating was up to 300hrs.
    Therefore, investigating the cause of destruction of this coating at high temperature oxidation, a considerable effort was exerted to obtain Cr-Ni coating with longer oxidation resistance life by improving the electro-deposition process, that is, anodic treatment for molybdenum surface before chromium deposition and expelling absorbed hydrogen in Cr-deposited layer which are the cause of blistering and spalling of Ni layer.
    By this improvement, the double deposited layer showing oxidation resistance life for maximum 700hrs, at 1000°C could be obtained when Cr layer was 0.025mm and that of Ni 0.150mm thick.
    The mechanism of oxidation of this coating was also investigated. The oxidation resistance of this coating mainly owes to the outer Ni layer and inner Cr layer has nothing directly to do with the oxidation resistance. The rate of weight gain by oxidation is slower than that of pure nickel because of the diffusion of chromium into nickel layer by heating. It was discerned by X-ray diffraction and qualitative analysis that the oxidation product on coated surface was not nickel oxide (NiO) but solid solution with face centered cubic lattice in which Cr, Ni and O atoms were arranged irregularly.
    Download PDF (2295K)
  • Hideo NAGASAKA, Yoko ONODERA, Takeshi TAKEI
    1959Volume 10Issue 9 Pages 355-360
    Published: September 20, 1959
    Released on J-STAGE: October 30, 2009
    JOURNAL FREE ACCESS
    Heat-resisting characteristics at temperatures between 900-1000°C, of the steel plate coated with ceramics by flame spraying were studied, and the following result was obtained. Flame spraying was carried out by powder method or rod method.
    1. Steel plate coated with fused Al2O3 is nearly 3 times more resistant to oxidation than bare steel. But the coating technique in this case is not easy and the film is liable to strip out.
    2. When metallic Cr is added to Al2O3, the porosity of the film is reduced and the oxidation resistivity is increased. The maximum of the porosity was found between the Cr content of 20-50%.
    3. The film is more closely adhered if the steel surface is at first covered with Fe-Al alloy and the flame spray is carried out on the alloy. Covering with Co metal with electroplating gives nearly the same effect.
    4. When the fused Al2O3 tube connected through hole with metal wire is used as spraying rod, very resistant coating is obtained as in the case of (2).
    Download PDF (1451K)
feedback
Top