Journal of The Society of Instrument and Control Engineers
Online ISSN : 1883-8170
Print ISSN : 0453-4662
ISSN-L : 0453-4662
Volume 1, Issue 10
Displaying 1-8 of 8 articles from this issue
  • [in Japanese]
    1962 Volume 1 Issue 10 Pages 737-746
    Published: October 10, 1962
    Released on J-STAGE: May 24, 2011
    JOURNAL FREE ACCESS
    Download PDF (4209K)
  • Aisuke KATAYAMA
    1962 Volume 1 Issue 10 Pages 747-756
    Published: October 10, 1962
    Released on J-STAGE: October 21, 2010
    JOURNAL FREE ACCESS
    A method of designing the adaptive control system for the invariant closed-loop dominant conjugate complex poles has been developed by use of root-locus techniques. The method can be applied only to the controlled element containing one variable parameter varying with the surrounding conditions. However, it is also possible to apply it to the case where the transfer function of the controlled element is given in higher order rational function of s, whose coefficients change in large scale from the nominal values. Two subsidiary loops are required for the adaptation, one for phase adjustment, the other for gain adjustment. Each loop is composed of a nonlinear function generator incorporating the corresponding programming curve obtained graphically from root-locus and a servo which drives the adjustable controller.
    Download PDF (4562K)
  • Tamotsu FUKUMOTO, Chikayasu YAMAZAKI
    1962 Volume 1 Issue 10 Pages 757-763
    Published: October 10, 1962
    Released on J-STAGE: October 21, 2010
    JOURNAL FREE ACCESS
    Pressure gauge movement can have a much better vibrating wear character with a suitable spring in place of movement link. When the mass of spring is large like a Bourdon tube, however, this improvement effect is small. The spring should be light and a few times as hard as Bourdon tube. Better wear character will be obtained with weaker spring. In this case, however, pressure gauge's normal frequency F0 drops too, resulting in reducing the range of use. It is pointed out once again that a lighter pointer has an advantage, because it raises F0. More care should be paid to the frequency Fc, it to be called “Critical Frequency”, F0, 3 F0, 5 F0, etc. It is not good to measure the dynamic pressure near the “Critical Frequency” of pressure gauge, because if it is done, resonance occurs, pointer is wildly vibrated and accordingly gear teeth are rapidly worn off. F0 is approximately 1000 cpm or less in general.
    Download PDF (1063K)
  • Yoshio IWABUCHI, Isamu KOMATSU, Makoto UEMATSU
    1962 Volume 1 Issue 10 Pages 764-771
    Published: October 10, 1962
    Released on J-STAGE: October 21, 2010
    JOURNAL FREE ACCESS
    The lithium chloride dew point thermometer has been noted as “Dew cell” since many years ago. Old type lithium chloride dew point thermometer has such weak points on practical use as it takes a long time from starting up to the time it has a stable pointing and it can not always start operation in the atmosphere of high temperature and high humidity. These weak points have been remarkably impro ved in the following ways:
    1) Use as an electrode a kind of platinum wire of higher resistance.
    2) Use a heat-treated glass fibre, into which aqueous solution of LiCl penetrates.
    Download PDF (6356K)
  • Eisuke MASADA
    1962 Volume 1 Issue 10 Pages 772-778
    Published: October 10, 1962
    Released on J-STAGE: October 21, 2010
    JOURNAL FREE ACCESS
    Although the recent development in numerical control of processes, especially in positioning control systems, is so remarkable, a few papers have been written on the design of such systems including quantizing elements.
    By phase plane approach, this paper attempts to study the synthesis of an on-off positioning servomechanism, which is commanded by discretely valued step inputs and similarly quantized outputs. The response to inputamplitude and total gain is obtained in graph from normalized phase plane loci. The system is able to approach the time-optimal system for wide range of input amplitude by adjusting the total gain at zero velocity errorpoints. This method is proved from phase portrait to be superior to other conventional methods, suchas a slow down method, a method adjusting the gain atzero error points, etc.An illustrative example makes it clear.
    Download PDF (976K)
  • Yoichi KAYA
    1962 Volume 1 Issue 10 Pages 779-785
    Published: October 10, 1962
    Released on J-STAGE: October 21, 2010
    JOURNAL FREE ACCESS
    Principle of inverse transfer function compensation is very simple and yet useful as a design principle of control system. A self-adaptive system with a variable parameter PID controller based on this princi ple has been developed. In this system, parameters of PID controller are selected so that zeros of transfer function of the controller may cancel the poles of process approximate transfer function. Dynamics of the control system and stability of the adaptive loop have been discussed with several examples.
    Download PDF (1108K)
  • [in Japanese]
    1962 Volume 1 Issue 10 Pages 786-790
    Published: October 10, 1962
    Released on J-STAGE: October 21, 2010
    JOURNAL FREE ACCESS
    Download PDF (882K)
  • [in Japanese]
    1962 Volume 1 Issue 10 Pages 791-794
    Published: October 10, 1962
    Released on J-STAGE: October 21, 2010
    JOURNAL FREE ACCESS
    Download PDF (5472K)
feedback
Top