-
富田 久雄
1986 年 52 巻 473 号 p.
1-6
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
-
小沢田 正, 鈴木 勝義, 高橋 伸
1986 年 52 巻 473 号 p.
7-15
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
本報では,円形断面を有する厚肉トーラスの自由振動を修正厚肉殻理論を用いて解析する.ラグランジュアンの停留条件より振動方程式および境界条件を導く.振動方程式は級数解を用いて厳密に解き,固有振動数および振動モードを求めている.数値計算では種々のパラメータが振動数に及ぼす影響を調べ,また古典薄肉殻理論との比較検討を行い回転慣性およびせん断変形の振動数に及ぼす影響を明らかにしている.
抄録全体を表示
-
末岡 淳男, 吉武 裕, 田村 英之, 堀田 邦彦
1986 年 52 巻 473 号 p.
16-23
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
外周上の2点に,相対速度の関数である摩擦力が働くミンドリン円板の自励振動を,平均法と直接数値積分法を用いて解析した.その結果,平均法では,摩擦点に対して空間的配置の異なる2種類の単一モードの安定解が存在することや,発生する振動モードと摩擦点間の角度の関係および摩擦力の大きさと発生モードの関係などが明らかになり,両手法の結果はよい一致を示した.また,実験と解析結果との非常によい定性的一致を確認した.
抄録全体を表示
-
末岡 淳男, 吉武 裕, 田村 英之, 堀田 邦彦
1986 年 52 巻 473 号 p.
24-31
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
前報に引き続き,外周上の2点に相対速度の関数である摩擦力が作用する円板について,内部共振の影響のある場合の自励振動を平均法と直接数値積分法を用いて解析した.その結果,平均法から,低次モードが主となる内部共振が発生し,しかも,空間的配置の異なる2種類の安定解があること,および,発生モードと摩擦作用点間の角度や摩擦力の関係が明らかになった.また,実験結果と解析結果のよい定性的一致をみた.
抄録全体を表示
-
五十嵐 昭男, 田島 清和
1986 年 52 巻 473 号 p.
32-39
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
軌道面または玉の表面にきずをつけた玉軸受を三相交流誘導電動機に組み込み,電動機の軸受けハウジングの半径方向および軸方向振動加速度を測定した.そして,きずの個数,きず角度,きずの大きさの組合せを種々に変えて振動の波形観察,振動パルスのピーク値の測定,瞬間周波数分析などを行った.その結果,電動機のきず玉軸受の振動の基本的な性質が明らかになり,さらに実機における玉軸受のきずの診断法を得ることができた.
抄録全体を表示
-
田村 英之, 近藤 孝広, 末岡 淳男, 植田 登
1986 年 52 巻 473 号 p.
40-47
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
既報に提案した調和バランス法を基調とする非線形定常振動の高速高精度計算および安定判別のアルゴリズムを改良,それを用いてソフトスプリング系 Duffing 方程式を解析した.主共振部周波数特性の高精度解を求め,主共振部の不安定域,孤立分枝,非奇数次解の分岐現象,分数調波振動 (二分の一,四分の一次),不規則概周期振動および主共振下すそ部の高調波共振 (二~七次) の存在を明らかにし,その一部を数値解シミュレーションで確認した.
抄録全体を表示
-
白石 明男
1986 年 52 巻 473 号 p.
48-54
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
粘性減衰を有する主系に,粘性,クーロン両摩擦を伴う動吸振器を取付け,主系質量の振動加速度の低減を計る場合の動吸振器の最良調整法について検討した.結果として, (1) 振動加速度の低減を目的とする場合には,振動変位のそれを計る場合とは異なる調整値を用いる必要がある,(2) 著者の作った実用計算式により,主系質量の振動加速度の低減に効果的な最良調整値を求め得る,などが明らかになった.
抄録全体を表示
-
成田 吉弘
1986 年 52 巻 473 号 p.
55-61
発行日: 1986/01/25
公開日: 2017/02/06
ジャーナル
フリー
通信,放送衛星に搭載される軸対称アンテナとオフセットアンテナの振動解析のため,その力学モデル化を検討した.その結果得られた解析モデルを,Donnell 形の偏平かく理論に基づいてリッツ法により解析し振動数方程式を導いた.数値計算において,対称な数点で固定された円形かくと,部分的に固定されただ円形かくの固有振動数を求め,曲率や支持位置がアンテナ鏡面に与える影響を考察した
抄録全体を表示
-
安田 仁彦, 浅野 武
1986 年 52 巻 473 号 p.
62-69
発行日: 1986/01/25
公開日: 2017/02/06
ジャーナル
フリー
振動モードが縮退している非線形振動系の動的応答の特徴を,二つの振動モードが縮退するような縦横比をもつ長方形膜を例にして検討した.一般的な解法を検討した後,具体例として,(1, 2) 次と (3, 1) 次の振動モードが縮退する長方形膜に調和外力が作用する場合の振動を解析した.解析の結果,膜は複雑な振動特性を示すことが明らかになった.アナログ計算機および実験により,理論解析がほぼ妥当なものであることを確認した
抄録全体を表示
-
吉本 成香, 角張 毅
1986 年 52 巻 473 号 p.
70-78
発行日: 1986/01/25
公開日: 2017/02/06
ジャーナル
フリー
本論文では静圧気体ジャーナル軸受の負荷容量および静剛性を高めるために,0リングの変形を利用した軸受形式を提案し,その静的特性を摂動による線形解法および差分法による数値解法を用いて理論的に明らかにした.さらに計算結果と実験結果との比較を行い,その妥当性を検討した.その結果本軸受は従来の自成絞り形軸受に比して,より大きな負荷容量が得られることが明らかとなり,その有用性が確認された
抄録全体を表示
-
小幡 文雄, 藤田 公明
1986 年 52 巻 473 号 p.
79-87
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
2円筒試験により荷重密度変動下の潤滑油の耐焼付き能を温度の観点から解明するための基礎として,く形状変動熱量による回転円筒の温度上昇を解析した.熱源作用域の温度上昇はせん光温度とバルクの温度上昇に分離できる.円周方向のバルクの温度上昇にはうねりを生じ,その大きさは,円筒一回転に要する時間と熱量変動の周期との比ζが整数で1に近いほどまた熱量変動の大きいほど大きい.大きいζでは熱伝達率の影響を受けにくい.
抄録全体を表示
-
小田 哲, 小出 隆夫, 池田 敏彦, 梅澤 清彦
1986 年 52 巻 473 号 p.
88-96
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
本論文では,まず種々の圧力角の歯車に集中荷重が作用する場合の歯のたわみ,曲げモーメントを差分法により求め,計算結果が測定結果とよく一致することを確かめるとともに,これらに及ぼす圧力角,歯数,歯幅の影響について明らかにしている.さらにこれらの結果に基づいて,種々の圧力角の歯車の歯の任意の点に集中荷重が作用する場合の,任意の点の歯のたわみ,曲げモーメントを求めるための近似式を導いている.
抄録全体を表示
-
小田 哲, 小出 隆夫, 梅澤 清彦
1986 年 52 巻 473 号 p.
97-104
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
本論文では,まず種々の圧力角の高歯歯車に集中荷重が作用する場合の歯のたわみ,曲げモーメントを差分法により求め,計算結果が測定結果とよく一致することを確かめるとともに,これらを求めるための近似式を導いている.さらにこれらの式と久保・梅澤の方法を用いて高圧力角並歯,高歯はすば歯車のかみあい時の歯元応力を計算し,測定結果と比較するとともに,歯元応力に及ぼす圧力角,歯たけの影響について明らかにしている.
抄録全体を表示
-
新井 典久, 青山 栄一, 原田 進, 森 夏比古, 岡本 宗治
1986 年 52 巻 473 号 p.
105-112
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
本研究は荷重分担率を考慮することにより,実際の荷重状態に近い条件で圧入歯車の解析 (有限要素法) を行い,歯車各部に生じる応力を調べ,歯元部および圧入面周辺の応力状態を明らかにしたものである.また,圧入平歯車の動的状態での締めつけ内圧を減少させる圧入面の半径方向引張応力に対する実用式を誘導し,これと圧入平歯車リム部の強度より圧入平歯車の設計時における締めしろ選定方法を検討し,その決定手順を示した.
抄録全体を表示
-
市丸 和徳, 和泉 直志, 木下 和久, 三室 日朗
1986 年 52 巻 473 号 p.
113-121
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
2円筒ころがり-すべり接触における焼付きについて,試験円筒の加工目方向 (周方向か軸方向か) と回転数比 (整数比か非整数比か) により4種の突起間干渉状態を設定し,焼付きまでの過程を詳細に調べた.その結果,調質材ローラの場合,加工目方向と回転数比により焼付き発生荷重が著しく異なることが明らかとなった.その原因は加工目方向と回転数比による油膜形成状態の相違と回転数比による局所的発熱状態の相違でよく説明される.
抄録全体を表示
-
小幡 文雄, 藤田 公明, 藤井 正浩, 松尾 浩平
1986 年 52 巻 473 号 p.
122-129
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
スコーリング発生と温度の関係ならびに歯車試験結果と2円筒試験結果との相関性をギヤ油基油の場合について検討した.混合潤滑状態からのスコーリング発生は,接触面最高温度および積分温度よりも,すべり速度,給油方向の影響を受けにくい歯面バルク温度と相関がある.歯車のスコーリング発生温度は歯車のかみあい始めまたはかみあい終わりのすべり率に対応した2円筒試験における焼付き発生直前のバルク温度を参照して推定できる.
抄録全体を表示
-
尾崎 龍夫, 船津 和幸, 渕 郁雄
1986 年 52 巻 473 号 p.
130-137
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
はすば歯車のバニシ転造について,素材の塑性押込み,工具と素材の歯の弾性たわみと弾性沈みを考慮した転造モデルを提案した.その際素材歯幅両端や歯先の端面効果を考慮に入れた.この転造モデルにより転造歯形や必要な工具修整歯形を理論的に求めた.また求めた修整歯形をもつ工具および標準歯形工具を用いた転造実験を行い,理論解析の有効性を確認した.
抄録全体を表示
-
本橋 元, 江村 超, 酒井 高男
1986 年 52 巻 473 号 p.
138-144
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
高いループゲインを有するクローズドループ式サーボ系用の減速機として,ローラインデックス装置と同様の予圧法によるグロボイダルカム式無背げき減速機構を試作した.また,カムの研削法として平面状砥石を用いる方法を検討した.試作したカム形状の測定には,三次元測定機と高精度のロータリエンコーダを使用した.また,かみあい試験の結果,ローラホイールのピッチ精度以上の回転精度が得られた.
抄録全体を表示
-
田中 道彦, 山田 朗, 北郷 薫
1986 年 52 巻 473 号 p.
145-153
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
著者らは既にねじ締結体への有限要素法および境界要素法の応用方法について述べた.これらの方法を改良すれば,ねじに働く外力と軸力の関係も容易に解析することができる.本論文では,有限要素法解析を中心に,外力作用下でのねじ締結体各部の振舞を容易に模擬できる方法について検討した.これらによれば,接合面の分離を含む任意の負荷状態における軸力の大きさを解析できるほか,得られた結果も従来の実験結果と良く一致する.
抄録全体を表示
-
沢登 健, 秋山 雪治, 中村 正信
1986 年 52 巻 473 号 p.
154-162
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
有限要素法を用いてコイルばねの応力解析を行い,静的応力解析では疲れ破壊の重要因子である最大主応力の大きさがばね内径側と外径側で交代するピッチ角の値は,有効巻数が小さくばね指数が大きいとき,これらの値に依存して大きく変動することを示した.動的解析では,正弦波状平行圧縮を受けるコイルばねの動的応力分布を比例減衰を仮定して求め,実験とよく合うことを示し,素線軸に沿うサージング応力の分布を明らかにした.
抄録全体を表示
-
中村 保, 加藤 浩三, 松井 伯夫
1986 年 52 巻 473 号 p.
163-172
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
新たに押出し形摩擦試験機を試作し,工業用純アルミニウム材料を用いて無潤滑・低すべり速度条件における焼付き発生機構の解明を試みた.ダイス出口の新生面露出位置で相対すべりも生じ焼付き発生の第1因となる.種々の面圧下で相対すべりを強制した摩擦試験と比較した結果,高面圧範囲では高摩擦拘束のため相対すべりが抑制され,また高静水圧のため素材表面相のせん断破壊が抑制され,焼付き発生が遅れることが明らかになった.
抄録全体を表示
-
梅崎 洋二, 鈴木 俊男, 井上 繁
1986 年 52 巻 473 号 p.
173-181
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
ホブ切トルクはホブ盤の振動や歯切精度などに影響する要因である.本報ではホブ切トルクの計算に必要な比切削抵抗を簡単に求めるため,前報の結果から実験の容易な二次元旋削を行った.二次元旋削で得た比切削抵抗をトルク計算に用いるとき修正する必要があるが,本報ではこの修正係数がモジュールや被削材が異なる場合など広範囲のホブ切においてどのような値になるか調べた.また修正係数に影響を及ぼす要因についても検討した.
抄録全体を表示
-
赤木 文男, 大崎 紘一, 菊地 進, 藤井 太一
1986 年 52 巻 473 号 p.
182-190
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
従来のライン編成手法は,工程の作業能力が不変であるとの仮定のもとで作業配分を行っていた.しかし,各工程の作業能力は作業者と設備の状態の違いによって変化する.そこで本報では,マイクロコンピュータを使用し,稼働中のラインの作業時間を動的に測定してリアルタイム処理し,各工程の作業遂行度を求める.そして,求めた遂行度に対応して工程ごとに工程時間の上限を変え,作業配分をきめ細かく行うライン管理システムを提案した.
抄録全体を表示
-
伊東 誼, 大見 孝吉, 島 吉男
1986 年 52 巻 473 号 p.
191-198
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
稼働例の急速な増大とともに,フレキシブル生産システム (FMS) の技術は急速に進展してきている.しかし,FMS のシステム設計や導入効果の判定上重要な FMS の経済性評価に関する研究は皆無に等しい.本研究では,このような FMS の評価に対してひとつの指針を与えることを目的として,システムの柔軟性評価ベクトルの概念を提案している.また,この概念を,小規模の FMS の評価に適用し,その妥当性を確認している.
抄録全体を表示
-
藤井 進, 三道 弘明, 市川 宏一
1986 年 52 巻 473 号 p.
199-208
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
物流費用を考慮して同種製品を生産可能な複数工場に生産品種と生産量を配分する問題を多品種多工場多期多地域に対する生産調整問題として定式化した.生産工場・生産期を特定した生産パターンを利用した2段階解法を示し,効率化に有効なパターンの発生法を生産選好指標,能力制約改善効果などを用いて検討した.これらの考え方に基づく発見的方法を構成し,数値例に適用することによりその妥当性,有効性を明らかにした.
抄録全体を表示
-
小沢田 正, 鈴木 勝義, 高橋 伸
1986 年 52 巻 473 号 p.
209-216
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
An exact method using power series expansions is presented for solving axisymmetric free vibration problems for shells of revolution having meridionally varying curvature. The govering equations of motion and the boundary conditions are derived from the stationary conditions of the Lagrangian of the shells of revolution. The method is demonstrated for shells of revolution having cycloidal, parabolical, elliptical, catenary and hyperbolical meridional curvature. The natural frequencies and the mode shapes are numerically calculated.
抄録全体を表示
-
入江 敏博, 山田 元, 岡田 一路
1986 年 52 巻 473 号 p.
217-223
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
An analysis is presented for the three-dimensional vibration problem of determining the natural frequencies and the mode shapes of axisymmetrical solid bodies, with a variable meridional profile expressed as an arbitrary function. For this purpose, the solid body is transformed into a solid cylinder of unit axial length and unit radius by a transformation of variables. With the displacements of the transformed solid cylinder assumed in the forms of algebraic polynomials, the frequency equation is derived by means of the Ritz method. This method is applied to solid bodies of revolution with a linear or a parabolic meridional profile under two combinations of boundary conditions at the edges. The natural frequencies and the mode shapes are calculated numerically up to higher modes, and the results are presented in some figures.
抄録全体を表示
-
高田 一, 大野 一彦
1986 年 52 巻 473 号 p.
224-228
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
The added mass of a vibrating plate in a fluid reduces the natural frequency of the plate in comparison with that in air. The ratio of the former to the latter is affected by the disc thinkness, the liquid density and a hole in the disc. In this research, two kinds of discs, 2.05 nm and 3.05 mm in thickness, and four kinds of liquids, 0.858, 0.890, 0.965, 1.000×10
3 kg/m
3 in density, are investigated to clarify their influences. In the experimental results, the values of the nondimensional formula, which contains the disc thickness or the liquid density, are almost the same at and below 0.33 in the ratio of the liquid depth to the diameter of the disc for the modes with a free surface. The effect of a circular hole in the center is very small, provided the area ratio of the hole to the plate without a hole is smaller than 0.0178.
抄録全体を表示
-
畠 進, 南方 留美
1986 年 52 巻 473 号 p.
229-232
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
In this report, two procedures to enhance subspace iteration method are presented. One is the method of multiple condensation to lower eigenvectors during one step of iteration (Fig. 3). We call this method multicondensation subspace iteration method. The other is strategy about selection of starting vectors in origin shifted subspace iteration method (Fig. 5). Starting vectors are set to have desirable quality.
抄録全体を表示
-
芳村 敏夫, 中川 賀之
1986 年 52 巻 473 号 p.
233-236
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
The stability and accuracy of the responses of nonlinear vibrational system using the direct integration methods are discussed. A nonlinear undamped-free vibrational system with one degree of freedom is illustrated for the numerical simulation, and the response of the system is evaluated using the Newmark-β method, the Wilson-θ method, the Houbolt method and the Gear-2 step method. The responses are computed using implicit integration algorithms with the iteration to establish dynamic equilibrium at the current time. The stability is discussed by deriving the characteristics z-polynomial equations, and it is checked whether all the roots of the equations exist in the left-hand of z-plane or not. The stability region and accuracy depending upon the time increments are numerically examined for the four direct integration methods.
抄録全体を表示
-
古石 喜郎, 武藤 浄
1986 年 52 巻 473 号 p.
237-243
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
This paper presents a study of the active control of structural vibration by an active mass damper system, which consists of a combination of a force generator, a sensor and a servomechanism. The systematic procedure for the synthesis of an active mass damper system is based on the use of modal control theory. The effectiveness of an active mass damper system is demonstrated by the results of a numerical analysis of the undamped vibration of a single degree of freedom system, and it is shown that the eigenvalues of the system can be assigned any arbitrary values by linear feedback of state variables.
抄録全体を表示
-
新谷 真功
1986 年 52 巻 473 号 p.
244-251
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
This paper deals with a new method of estimating the accumulated damage (D-value), a proposal for design d-value spectrum and their applications to nuclear piping system seismic designing. The earthquake waves employed to calculating d-value spectrum are artifical and world famous earthquakes. Then we can present a design d-value spectrum that is not influenced by input earthquake characters since we take an envelope spectrum of these d-value spectra. Applicational example indicate where D-value is evaluated from the design d-value spectrum. The ratio of the D-value to the critical one corresponding to a safety limit for design, which will be obtained by experiments, shows a good index for safety reliability of nuclear piping systems.
抄録全体を表示
-
中村 友道, 藤田 勝久, 山口 信行, 坂田 薫, 柘植 綾夫, 斎藤 格
1986 年 52 巻 473 号 p.
252-257
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
Large amplitude vibration caused by a high-speed air water two-phase flow is investigated. It is thought to be the same phenomenon as fluid-elastic vibration. However, it intermittently occurs and is not so great as to damage the tubes. Small-size test tube bundles, whose natural frequencies are tuned to adequate low frequencies, are excited by an air-water two-phase flow. The air velocity is increased step by step, while the water velocity is kept constant. The amplitude of the tubes is gradually increased with the increase of flow velocity, and is not abruptly changed as is likely by the single-phase flow. However, the phenomenon can be distinguished from random excitation. The method to decide the threshold velocity of this new type of instability is proposed by comparison with the test results of the single-phase flow.
抄録全体を表示
-
西郷 宗玄, 岩壺 卓三
1986 年 52 巻 473 号 p.
258-263
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
Torque-induced lateral instability of rotor systems coupled by Constant-Velocity joints is theoretically investigated for different four types of model ; flexibly-supported rigid rotor models of working machines, such as compressor or turbine, and those of transmission shafts for both 2-degrees-of-freedom system and 4-degrees-of-freedom system. The instability regions are calculated including the effects of the asymmetry of the rotor support stiffness, the initial intersecting angle between the rotor shaft and the driving or loading shaft, and the gyromoment of the rotor shaft. The relation between the characteristics of instability and the matrix elements of the equation of motion concerning the transmitted torque is investigated and the mechanism of instability due to the transmitted torque is discussed.
抄録全体を表示
-
杉山 吉彦, 松本 新吾, 岩壺 卓三
1986 年 52 巻 473 号 p.
264-270
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
The effect of a damper on the critical flow velocity of a cantilevered system of two articulated pipes conveying fluid is investigated analytically and experimentally. It is shown that a damper attached to the system at the mid-portion of the span has a stabilizing effect, while the same damper at the tip portion has a destabilizing one. The greatest destabilizing effect takes place when a damper is located at the discharge end. The percentage destabilization due to the introduction of a damper is found to be higher than the percentage stabilization.
抄録全体を表示
-
長谷川 英治, 近藤 伸和
1986 年 52 巻 473 号 p.
271-278
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
Instabilities of a liquid layer, over which a thin viscous liquid layer is superposed, are investigated theoretically and experimentally under vertical periodic motion. It is assumed that the depth of the lower layer is finite and that of the upper one is very small. Thus, the motion of the lower and upper liquids are treated as an irrotational flow and a viscous flow, respectively. The neutral curves, which separate the stable region from the unstable one in the plane of the frequency and the amplitude of an externally imposed acceleration, are found by using a linear theory. The neutral curves depend on the Reynolds number, the depth ratio, the density ratio, the Weber number and the ratio of the surface tension coefficient. The motion of the ideal fluid layer is found to be stabilized by superposing a thin viscous liquid layer. The theoretical results are fully confirmed by those experimentally undertaken in the water-oil liquid layer.
抄録全体を表示
-
内海 雅彦, 木村 康治, 坂田 勝
1986 年 52 巻 473 号 p.
279-287
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
The non-stationary response of an elastic circular cylindrical tank partially filled with liquid is investigated to a simulated earthquake excitation with two-directional horizontal components. The earthquake accelerations are modeled as amplitude modulated random processes and the mean and standard deviation responses of the liquid surface displacement and wall deformations are calculated to both the simulated long and short period earthquake excitations, which respectively cause sloshing and bulging type motions to the liquid-tank system. It is shown that consideration of nonlinearity in the liquid motion and also cross-correlatios between two-directional components of the earthquake excitation is important for obtaining an acculate response analysis and also a reasonable estimation for seismic safety of liquid storage tanks.
抄録全体を表示
-
成田 吉弘
1986 年 52 巻 473 号 p.
288-293
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
The free vibration of a deployable antenna used in the communication satellite is considered analytically. The antenna reflector is modelled as the point supported shallow shell of elliptical planform, consisting of small shell segments combined each other by point joints. In the analysis, a Ritz method is used as a basic approach and Lagrange multipliers are introduced to accommodate constraint conditions on the point conjunctions, as well as on the supports. Numerical results are presented which demonstrate effects of varying the geometric parameters of segment locations, curvature and support locations on the vibration characteristics.
抄録全体を表示
-
安田 仁彦, 鳥居 孝夫
1986 年 52 巻 473 号 p.
294-301
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
A nonlinear nonsymmetric forced oscillation induced in a circular membrane subjected to harmonic excitation, is examined using a typical example. For theoretical analysis, modal equations are first derived from the governing partial differential equations. Then, based on these modal equations, a forced oscillations is discussed near one primary resonance point, i. e., the resonance point when the excitation frequency comes near to the natural frequency of the mode with one diametral nodal line. The analysis reveals that, in addition to the usual harmonic oscillation, a kind of traveling wave occurs. This occurs because two modes existing with the same natural frequency and the same shape but shifted circumferentially by the angle π/2, are induced with the phase lag π/2. Experimental analysis, conducted with the use of a thin steel membrane, confirms the validity of the theoretical analysis.
抄録全体を表示
-
坂本 東男, 山本 三幸
1986 年 52 巻 473 号 p.
302-309
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
In order to clarify the effect of nonlinear creep force on railway truck dynamics, an analysis, including saturation characteristics in creep force, has been formulated. Numerical simulations using the RKG algorithm have been performed with a 6 degrees-of-freedom truck model. The results indicate that the truck vibrations are considerably different from those obtained by linear analysis, especially in the stability. The stability depends on the amplitude of vibrations ; large amplitude makes the vibration unstable. Conclusively, this nonlinear analysis gives a lower critical speed than that by linear analysis. The difference is found to be 5-25 (m/sec), which explains more likely the hunting characteristics in service.
抄録全体を表示
-
鈴木 真二, 今井 守之, 石山 慎一
1986 年 52 巻 473 号 p.
310-317
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
The boundary element acoustic analysis is coupled with structural modal analysis for predicting sound fields generated by vibrating structures. The dynamic equation of the structure is represented by modal parameters obtained by structural analysis. The acoustic equation of the fields is described using the boundary element analysis of the Helmholtz integral equation. These two equations are solved simultaneously. Numerical results are shown to demonstrate the accuracy of our method in comparison with experimental ones. The sound transmission through a cavity-backed plate is studied as the case of an interior problem. As the exterior problem, sound radiation is examined from a plate excited by a hammer.
抄録全体を表示
-
藤岡 健彦, 竹内 正治, 井口 雅一
1986 年 52 巻 473 号 p.
318-325
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
The former part of this paper describes an experimental study on the creepage and creep force law. The study has been carried out on a one-third scale model test-rig. By the test-rig, creep forces which correspond to three creepages-longitudinal, lateral and spin-are measured. The results of the experiments give good agreement with the values that have been obtained by the Kalker's creep theory. In the later part of this paper a simple method which calculates creep forces is proposed. The creep forces calculated by the algorithm give good agreement with the values calculated by the Kalker's theory. This method can also represent the decreasing of creep forces in the high-creepage area which is caused by the difference between friction coefficients of stick and slip.
抄録全体を表示
-
小野 京右, 前野 隆司, 海老原 毅
1986 年 52 巻 473 号 p.
326-335
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
In order to get better understanding of head to flexible disk interface problems, Green's function for a spinning flexible disk deflection is derived by extention of the analytical method proposed for a stationary flexible disk in the previous paper. As a result, it is found that a flexible disk has many resonance speeds where each circumferential mode component is excited by a stationary force. The external stiffness has the effect of increasing these resonance speeds ; whereas the external damping makes the disk deflection asymmetric with respect to the applied force. The restraining effect of a liner used in an available floppy disk cartridge on the disk deflection is clarified by the numerical analysis for a disk model supported partly by a set of external springs. Theoretical results are roughly verified by the experiments.
抄録全体を表示
-
大矢 誠, 穂苅 久, 田村 久司
1986 年 52 巻 473 号 p.
336-343
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
For the purpose of the improvement in measuring accuracy of three-coordinate measureing machine, the measuring method of the systematic errors is proposed. The method described here is based on the distance measuring method which was reported in the earlier paper by authors, and is adequate to determine the distribution of error vector in the measuring range. Then measurement was practically carried out and the distributions of error vector were clarified about two types of three-coordinate measuring machines. In connection with the experimental results, the relation between the distribution of error vector and the geometrical accuracy of machines is discussed. Also the variation of error vector according to the room temperature change is examined and the results is reported.
抄録全体を表示
-
福田 敏男, 栗林 豊, 細貝 英実, 矢島 信之
1986 年 52 巻 473 号 p.
344-348
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
In this paper, a differential solar cell sensor consisting of a pair of adjacent solar cells is proposed as a new type of sensors to measure vibration of flexible solar battery arrays and to orient the array toward the sun correctly. This sensor, which is small and light, has characteristics of linearity and can be implemented easily without compensation of distance. To elliminate noises in the sensor outputs, the Kalman filtering method is employed, based on the dynamics of a flexible solar arrays which is developed in a different way of the previous paper. Then all states can be fed back in an optimal closed control system, so that the control performance can be improved in vibration and attitude control.
抄録全体を表示
-
福田 敏男, 細貝 英実, 矢島 信之
1986 年 52 巻 473 号 p.
349-353
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
An actuator problem is dealt with in this paper in controlling vibrations of flexible solar battery arrays and orienting the array toward the sun correctly. A Lero momentum type of a reaction wheel which is in common use is selected as an actuator in space here. Then the flexible array can be controlled by a reaction force working in the opposite direction of the rotation of the reaction wheel. Therefore, there is close coupling between the flexible array and the reaction wheel. First, the dynamics of the coupling system is derived here including the shaft rigidity between them under the assumption that the flexible array vibrates only in the bending way. Then the feedback control law is given to control the orientation and the vibration of the flexible array, employing the differential solar battery sensors as vibration and orientation measurement. The effect of the inertia moment of the reaction wheel is also considered experimentally with respect to the settling time of the flexible array.
抄録全体を表示
-
河合 望, 堂田 邦明, 中島 嘉宏
1986 年 52 巻 473 号 p.
354-360
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
A compression-twist type friction testing machine has been developed to establish the fundamental friction testing method for metal forming. This machine has been devised to change easily contact pressure, sliding velocity, sliding distance and combination of friction pairs. Two indenter types, that is, ones with different contact length along sliding direction and a ring-shape-indenter, are employed and several mineral oils are tested using mild steel and alloy tool steel SKD 11 as the friction pairs. Surface appearances of testpiece and tool during sliding are observed by a SEM and a profile projector. The variations of friction coefficient during sliding are understood based on the surface appearance. Thus, new measures to evaluate lubricity in boundary lubrication, oil film strength and antiweldability are proposed.
抄録全体を表示
-
寺内 喜男, 野西 利次
1986 年 52 巻 473 号 p.
361-366
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
In a previous paper, the authors investigated the fluctuation of oil film pressure and the vibration of cylinders caused by eccentricity and waviness, using rolling cylinders lubricated with mineral oil. In this paper, the fluctuation of oil film pressure and the vibration of cylinders caused by the periodical change in the width of contact surface has been studied. The width of the contact between a plane and a cylinder was varied by partially shaving off the cylinder surface. The fluctuation of oil film pressure and the vibration of cylinders were measured, using an apparatus specially made for this experiment. Then, theoretical values given by numerical calculation were compared with the measured values.
抄録全体を表示
-
田村 久司
1986 年 52 巻 473 号 p.
367-373
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
Point-contact spiral bevel gears substantially have both lengthwise and profile ease-off to get smooth action in the gearing. This paper is concerned with the gear cutting method of point-contact spiral bevel gears with a tapered tooth height. In the method, the cutter axis is not tilted. The point-contact gears are obtained by the Gleason type cutter in which inside blades are modified to a circular arc. A pair of gears cut by this method meshes with little relative curvature. The main procedure of the method is to determine THE MACHINE SETTING taking account of the gear engagement. The theory is developed assuming that the Gleason hypoid generator is used without cutter-tilt and the generating relationships are unaltered.
抄録全体を表示
-
塚本 尚久
1986 年 52 巻 473 号 p.
374-379
発行日: 1986/01/25
公開日: 2008/02/21
ジャーナル
フリー
Intermeshing a steel gear with a plastic gear allows for nonlubricated running. In such a case, differences in the finish of the tooth flanks of the steel gear affect on the wear of plastic gear. For example, finely ground steel gear teeth reduce plastic gear wear by 30 to 40 percent, compared with hobbed teeth. However, it is not preferable to grind steel gear teeth by using the MAAG 0-degree method, because the teeth cause loading by wear powder of nylon gear. Although grinding marks are desirable to lie in a direction of tooth profile, this is difficult to work. Therefore, we grind steel gear teeth by using the MAAG 15-degrees method which produces grinding marks somewhat nearen the desirable ones, perform the wear test with nylon gears, and examine the difference in effect between the 0-degree method and the 15-degrees method.
抄録全体を表示