巻号一覧
4 巻 (1978)
- 4 号 p. 133-
- 3 号 p. 93-
- 2 号 p. 49-
- 1 号 p. 1-
4 巻, 3 号
選択された号の論文の8件中1～8を表示しています
- |<
- <
- 1
- >
- >|
-
山田 敏郎, 可児 弘毅1978 年 4 巻 3 号 p. 93-99
発行日: 1978/07/31
公開日: 2009/08/11
ジャーナル フリーPDF形式でダウンロード (5488K) -
騒音および振動制御用材料佐々木 雄貞, 遠藤 紘1978 年 4 巻 3 号 p. 99-104
発行日: 1978/07/31
公開日: 2009/08/11
ジャーナル フリーPDF形式でダウンロード (991K) -
芳我 攻1978 年 4 巻 3 号 p. 105-111
発行日: 1978/07/31
公開日: 2009/08/11
ジャーナル フリーIt is assumed that elastic properties of glass fabric reinforced plastic laminates are affected by three factors, i.e, the deflection angle, the pitch and the density of warp and weft of the fabrics. The elastic moduli of glass fabric reinforced plastic laminate are calculated by a crossply laminate model consisting of many unidirectional reinforced monolayers at right angles to each other. The mechanical properties of the monolayer are estimated by considering the three factors. The elastic moduli of this model are analyzed by using “laminated plate theory”, and the macroscopic failure criterion is discussed based on the maximum stress theory and the strain energy theory. The elastic moduli and the yield stresses of three foundation weave fabric laminates (plain weave, twill weave and satin weave) are measured experimentally. The calculated values agree fairly with those of experiments, and it is concluded that the analytical method presented in the paper is useful to predict the elastic moduli and the yield strength of glass fabric reinforced plastic laminates.抄録全体を表示PDF形式でダウンロード (1012K) -
第II報 半角くさびによるガラス繊維の剥離および破壊について井上 久弘, 井戸 守1978 年 4 巻 3 号 p. 112-118
発行日: 1978/07/31
公開日: 2009/08/11
ジャーナル フリーThe indentation of unidirectional glass fiber reinforced plastic materials by half-wedge indenters was accomplished. The whitening patterns being produced by indenting are classified into two categories which these are fractured part perfectly and the failure part involving some defects for glass yarns in view of fracture behavior. The distribution of failure pattern (whitening pattern) defined are observed on various relative angle between the wedge face and the direction of yarn in composites and those are compared with that of full wedge indenter mentioned in previous paper. The main results obtained are as follows : (1) The failure pattern by half-wedge indenter dose not show the peculiar behavior presented in the case of full wedge indenter. (2) According as the wedge angle increase, the fracture part spreads in the vertical direction of wedge face in the case of full wedge indenter, while spreads under the indenter in the case of half-wedge indenter. (3) The fracture of yarn occurs in a combination of horizontal stress acting in the direction of fiber and bending moment, whereas failure of yarn occurs with stress acting vertically to the yarn orientation.抄録全体を表示PDF形式でダウンロード (7201K) -
石川 隆司, 小山 一夫, 小林 繁夫1978 年 4 巻 3 号 p. 119-124
発行日: 1978/07/31
公開日: 2009/08/11
ジャーナル フリーIn the temperature range from room temperature to the glass-transition point (Tg) of matrix, elastic moduli of CFRP-UD composites, CFRP-FW cylinders and Epoxy resin are measured. An electro-optical extensometer, Zimmer model 200 X, is used in these experiments. Experimental results of Ex are compared with the numerical results by the authors' computer program based on measured data for Epoxy and an agreement is very good. Temperature dependency of Ex is directly influenced by that of Em, but Ez is almost independent of Em. It should be noted that νm has considerable effect on Ex, particularly at near Tg point. Curing temperature history changes trends of temperature dependency of Em at most Epoxy.抄録全体を表示PDF形式でダウンロード (2096K) -
1978 年 4 巻 3 号 p. 125-128
発行日: 1978/07/31
公開日: 2010/02/08
ジャーナル フリーPDF形式でダウンロード (622K) -
赤坂 隆1978 年 4 巻 3 号 p. 132
発行日: 1978/07/31
公開日: 2009/08/11
ジャーナル フリーPDF形式でダウンロード (206K) -
島村 昭治1978 年 4 巻 3 号 p. 132a
発行日: 1978/07/31
公開日: 2009/08/11
ジャーナル フリーPDF形式でダウンロード (205K)
- |<
- <
- 1
- >
- >|