粉体および粉末冶金
Online ISSN : 1880-9014
Print ISSN : 0532-8799
ISSN-L : 0532-8799
検索
詳細検索
OR
閲覧
検索
62 巻, 7 号
July
選択された号の論文の7件中1～7を表示しています
すべての抄録を表示する
    • |<
    • <
    • 1
    • >
    • >|
研究論文
研究論文
特集：各種粉末の焼結機構と新しい焼結技術の展開
総報
研究速報
  • SPS成形した銅/ダイヤモンド複合材料の熱伝導率に及ぼすCr添加の影響
    水内 潔, 井上 漢龍, 上利 泰幸, 杉岡 正美, 田中 基博, 武内 孝, 谷 淳一, 川原 正和, 巻野 勇喜雄, 井藤 幹夫
    2015 年 62 巻 7 号 p. 357-364
    発行日: 2015/07/15
    公開日: 2015/07/28
    DOIhttps://doi.org/10.2497/jjspm.62.357
    ジャーナル オープンアクセス
    抄録を表示する抄録を非表示にする
    Diamond-particle-dispersed-copper (Cu) matrix composites were fabricated by spark plasma sintering (SPS) process from the mixture of diamond particles, pure-Cu and chromium (Cr) powders. The microstructures and the thermal conductivities of the composites fabricated were examined. These composites were all well consolidated at a temperature of 1173 K for 600 s by SPS process. No reaction at the interface between the diamond particle and the Cu matrix was observed by scanning electron microscopy and X-ray diffraction analysis for the composites fabricated under the sintering conditions employed in the present study. The relative packing density of the diamond particle dispersed Cu matrix composites with Cr addition was 4.4~5.9 % higher than that without Cr addition. The thermal conductivity of the Cu/diamond composite drastically increased with Cr addition. The thermal conductivity of (Cu-Cr)-50 vol% diamond composites was 518~584 W/mK in a volume fraction range of Cr between 2.5 and 8.6 vol% in Cu matrix. Numerous transgranular fractures of diamond particles were observed on the bending fracture surface of diamond particle dispersed Cu matrix composites with Cr addition, indicating strong bonding between the diamond particle and the Cu matrix in the composite.
    抄録全体を表示
    PDF形式でダウンロード (2238K)
研究論文
  • 合金粉末を原料とする高強度チタン合金の製造
    叶野 治, 深田 伸男, 早川 昌志
    2015 年 62 巻 7 号 p. 365-370
    発行日: 2015/07/15
    公開日: 2015/07/28
    DOIhttps://doi.org/10.2497/jjspm.62.365
    ジャーナル オープンアクセス
    抄録を表示する抄録を非表示にする
    In order to develop low-cost and high-strength titanium alloy, a production method using pre-alloyed titanium powder has been investigated. Ti-6Al-4V pre-alloyed powder was prepared by HDH process using Ti-6Al-4V alloy turning chip as a starting material. Mixed powder of Ti-6Al-4V pre-alloyed powder and 3 to 4 % iron powder was consolidated by hot extrusion process. In this study, the following results were obtained. Almost full densification of pre-alloyed powder has been confirmed by hot extrusion process. Titanium alloy containing high amount of iron up to 4 % can be produced without iron segregation by powder metallurgical process. This titanium alloy possibly shows higher tensile strength by 2 to 30 % than Ti-6Al-4V alloy maintaining elongation of 10 %. These data suggest that highly iron containing titanium alloy produced by pre-alloyed powder method possesses high potential as a material for aerospace and automobile.
    抄録全体を表示
    PDF形式でダウンロード (1247K)
技術速報
  • 一体成形・焼結した複層軸受の強度と摩擦摩耗特性
    毛利 敏彦, 須貝 洋介, 伊藤 容敬, 湯浅 栄二
    2015 年 62 巻 7 号 p. 371-376
    発行日: 2015/07/15
    公開日: 2015/07/28
    DOIhttps://doi.org/10.2497/jjspm.62.371
    ジャーナル オープンアクセス
    抄録を表示する抄録を非表示にする
    The composite journal bearings which have outer layer with high strength and inner layer with high wear resistance can be used as bearing materials in the industrial high-power machine. The complex layer bearing prepared by unification forming of two different mixed powders with Fe-Cu-C in outer layer and Fe-Cu-C-Ni-Mo in inner layer, and then it was sintered for various heating times at 1378 K~1403 K. Mechanical properties of the bearing were investigated by determinations of Vickers hardness and radial crushing strength. The radial crushing strength of sintered bearing with outer layer composition of Fe-Cu-C mixed powder is increased by the addition of phosphorus of 0.2~0.6 weight% (Specimen F). Nevertheless the apparent density of this complex bearing is low. The friction and wear properties in this bearing also were estimated. The sliding property to hardening steel shaft of the complex layer bearing was invested by swing-type sliding machine. Wear loss volume of Specimen F is low under high applied load it is very suitable for use of the industrial high-power machine.
    抄録全体を表示
    PDF形式でダウンロード (1184K)
本会記事
    • |<
    • <
    • 1
    • >
    • >|
feedback
 Top