Atelocollagen-gelatin (ACG) sponge was fabricated from atelocollagen and gelatin by lyophilization without introducing toxic substances. This study aimed to investigate the effects of heat treatment on the 3-dimensional structural stability of ACG sponge biomaterial. ACG sponge samples were fabricated and heat treated at 125^oC for 12 h in the vacuum. The results revealed that heat treatment did not affect porosity, pore size and mechanical compressive strength. Heat-treated ACG sponge showed decreased absorbance and peak shift of amid I (C=O) stretches, slightly higher water uptake degree and significantly decreased in vitro degradation rate. Moreover, heat-treated ACG sponge maintained good 3-dimensional surface morphology and porous microstructure throughout 7 days, while non-heat-treated ACG sponge collapsed in less than 24 h. The human mesenchymal stromal cells (hMSCs) were shown to adhere and grow well on heat-treated ACG sponges. These results indicate that heat treatment is effective and safe to stabilize 3-dimensional ACG sponge biomaterial for tissue engineering.

The aim was to obtain bone repair materials with sustained release of minocycline and evaluate the effect in periodontal bone defect repair. Two complex material, hydroxyapatite/chitosan (HA/CS) and minocycline-hydroxyapatite/chitosan (Mino-HA/CS), were prepared by the co-precipitation method. The physical and chemical property, cytotoxicity, release of minocycline and the bacteriostasis examination of the materials were evaluated, they were applied to the rabbit model of mandible bone defect to evaluate their effects on the regeneration of periodontal bone defect. After minocycline was added to HA/CS, the setting time of the material was prolonged, the compressive strength was reduced and the pore size and porosity were increased significantly. The pH value did not change obviously and stayed in the neutral range. Mino-HA/CS could promote the growth of osteoblasts effectively compared with control medium. In vivo, Mino-HA/CS material showed better effect of promoting periodontal bone formation.

This study investigated the influence of application/wash-out times of sodium hypochlorite (NaOCl) and hypochlorous acid (HOCl) on dentin bond strength of one-step self-etch adhesives (1-SEAs). Human coronal dentin discs with a standardized smear layer were pretreated with 6% NaOCl or 100 ppm HOCl for 5 s, 15 s, or 30 s, and washed out with water for 5 s, 15 s or 30 s with or without the application of Clearfil DC Activator (CDA). No pretreatment was used as a control. The discs were bonded with a 1-SEA (Bond Force II or Clearfil Universal Bond Quick) and microtensile bond strength (µTBS) was measured after 24 h. Pretreatment with NaOCl for 15 s and 30 s significantly decreased µTBS (p<0.05), irrespective of wash-out time. The application of CDA recovered µTBS but did not outperform the control group. Conversely, pretreatment with HOCl for 15 s and 30 s followed by 30 s wash-out time significantly increased µTBS of 1-SEAs (p<0.05), regardless of CDA application.

This study evaluated the 3-dimensional (3D) fit of self-glazed zirconia monolithic crowns fabricated by wet deposition, in comparison with milled zirconia and lithium disilicate monolithic crowns. Dual-scan protocol was used to assess the fit of crowns. Root mean squares (RMS) and uniformity index (UI) were calculated to describe the gap size and uniformity. The self-glazed zirconia crowns had significantly lower RMS values for the gaps at axial wall and transition regions than the milled zirconia crowns, and for the gaps at occlusal region than both milled crowns. All 3 types of crowns had comparable RMS values for the gaps at marginal and chamfer regions and comparable UI values for both marginal and internal gaps. The 3D fit of the self-glazed zirconia monolithic crowns was clinically acceptable and they exhibited better fit at occlusal region than the milled crowns.

This study evaluated the antibacterial activity of colloidal platinum nanoparticles (CPNs) toward Streptococcus mutans (S. mutans) viability. S. mutans 109c was treated with water and three CPN solutions at 37°C for 24 h (i.e., control, PAA-Pt, C-Pt, C-CyD-Pt). Dilution series (10^–1–10^–5) were prepared using brain heart infusion (BHI) broth for all samples, and a 100 µL suspension of each dilution was spread onto a BHI agar plate. Colony-forming units (CFU/mL) were determined after 24 h. The effects of CPNs on S. mutans survival and biofilm formation were investigated using fluorescence and scanning electron microscopies. The antibacterial rate of S. mutans increased with increasing concentrations of all three CPNs, with PAA-Pt nanoparticles exhibiting the highest antibacterial efficacy. CPNs were found to reduce S. mutans growth and inhibit biofilm formation remarkably.

This study evaluated stresses generated at maxillary central incisor (21) root restored with lithium disilicate crown (LDC), and glass fiber (GFP) or polyetheretherketone (PEEK) post. 3D models created by computed tomographic image (i-CAT Cone Beam 3D Dental Imaging System) reproduced maxillary central incisor. Each model had prosthetic LDCs (2.0 mm thick) cemented to GFP or PEEK posts with dual resin cement. Different loads were applied to each model (cervical, incisal, axial, middle). At maximum principal stress, PEEK showed higher stress than GFP in all loads, but with qualitative similarity. At minimum principal stress, PEEK and GFP showed qualitative and quantitative similarities, except axial load. Maxillary central incisor restored with GFP or PEEK and LDC presented, in general, similar stress intensity and distribution for main occlusal loads. Only two of sixteen occlusal loads tested (cervical for maximum principal; axial for minimum principal) showed significant quantitative difference.

The purpose of this study was to investigate the effect of various surface treatments on the shear bond strength between dental polyetheretherketone (PEEK) and adhesive resin cement. Two hundred and forty specimens were randomly classified into four groups: no treatment, sandblasted, sulfuric-acid-etched, and laser-grooved treatment. Each group was classified into two adhesive resin cement subgroups. Surface roughness, water contact angle, shear bond strength, and failure mode were measured; SEM and XPS results were obtained. The data were statistically analyzed using one-way or two-way analysis of variance and Tukey’s honest significant difference test (α=0.05). Laser-grooved PEEK surface showed regular grooves and carbonization by thermal degradation; the surface roughness as well as water contact angle of were the highest in all groups. Shear bond strength values were significantly higher in the laser-groove-treated and sulfuric-acid-etched groups. Laser-groove-treated specimens showed cohesive failure. Laser-grooved treatment can improve shear bond strength between PEEK and adhesive resin cement.

Human periodontal ligament stem cells (hPDLSCs) are seeding cells for tissue-engineered treatment of alveolar bone regeneration. To elucidate carboxymethyl chitosan (CMCTS) and carboxymethyl chitin (CMCT) effect on osteogenic differentiation, hPDLSCs were isolated and treated with CMCTS or CMCT. Cell viability and multiplication capacity were measured. The expression of classic osteogenic related molecules, including Alkaline Phosphatase (ALP), Phosphoprotein 1 (OPN), RUNX family transcription factor 2 (Runx2) and Osteocalcin (OCN), were determined. Mineralization levels were detected by Alizarin Red staining. Results showed that both CMCTS and CMCT treatment had the maximal promoting ability for hPDLSCs viability below the concentration of 100 μg/mL, while CMCTS improved hPDLSCs mineralization significantly. CMCTS induced multiple-factor high expression, including ALP, Runx2, OPN and OCN, whereas slightly osteoinductive bioactivity of CMCT was mainly due to ALP. Therefore, CMCTS had a more significant advantage for osteoinductive differentiation of hPDLSCs than CMCT, which may be a promising material for periodontal regeneration.

The aim of the present work was measuring the effect of varying normal forces on frictional forces applied to different bracket types in combination with archwires made of NiTi and stainless steel of variable cross section. The measurements were carried out in artificial saliva. Three-way ANOVA and Bonferroni post-hoc tests (α=0.05) were applied. Except for one subgroup the combination of normal force, bracket system and wire dimension had significant effect on friction (p<0.001) as friction increased with increasing normal forces. Only moderately tied ligatures or passive self-ligating brackets generate low friction forces. There was a statistically significant order (0.016"×0.022"<0.018"×0.025"<0.019"×0.025") for stainless steel wire material. Finite element modeling simulation showed the increasing effect of active clip force on friction especially for 0.025" wire profiles. If compared to NiTi wires, stainless steel archwires delivered higher friction. Combinations between wire-type and ligation should be chosen carefully for the intended treatment step.

Since cast titanium prostheses have many drawbacks, multi-directionally forged titanium grade 2 (MDF) was developed, and the application of the milling process was proposed for improving the titanium clasp. This in vitro study evaluated milled titanium clasps, including MDF titanium. Milling clasps were manufactured with commercially pure (CP) titanium grade 2 (CP 2), grade 4 (CP 4), Ti-6-Al-4V, and MDF. As a control, a CP 2 cast titanium clasp was fabricated in the conventional manner. No porosities and catastrophic failures were observed in the four milled titanium clasps. Fitness accuracy and retentive forces of milled CP 2 and CP 4 tended to be worse, and the milled MDF showed the higher retentive forces (12.45 N) than did cast and milled CP 2 clasps (9.32 N and 4.42 N). Milled titanium clasps can be recommended for longer-term clinical use as compared to cast clasps.

The cytocompatibility and osteoconductivity of the Zr-14Nb-5Ta-1Mo alloy were investigated using a mouse osteoblastic cell line (MC3T3-E1) to promote the application of this newly developed alloy in dental/medical treatment. The initial cell-attached morphology was visualized by fluorescent staining, and cells cultured on the Zr alloy showed similar cell adhesion behavior to cells cultured on titanium (Ti). In our 5-day proliferation investigation, similar cell numbers were obtained with both Zr alloy and Ti. These results indicate that the cytocompatibility of Zr alloy is similar to that of Ti. In addition, the similar results in the evaluation of alkaline phosphatase (ALP) activity and staining of deposited calcium using alizarin red S with both Zr alloy and Ti indicated that the osteoconductivity of the Zr alloy is similar to that of Ti. Our results prove the good cytocompatibility and osteoconductivity of the Zr-14Nb-5Ta-1Mo alloy, enabling its promotion for use in dental/medical applications.

We sought to compare the bond strength of resin cement on moist dentin to that on dry dentin, and determine the relationship between the bond strength and flexural strength of resin cement. The water content of the moist and dry dentins was estimated using infrared spectroscopy. Four adhesive and three self-adhesive resin cements were used. At three times of immediately, after one-day storage, and after 20,000 thermocycles (TC 20k), the shear bond strengths were measured. For all resin cements, both the shear bond strength and the flexural strength were the lowest immediately after setting; however, after one day of water storage or TC 20k, these resin cements had the highest values. Regardless of the condition of the dentin surface upon shear bond strength, the flexural strength of each resin cement was correlated with the shear bond strength of the dentin surface.

Due to its low tolerance to external factors such as enzymes, dentin collagen often requires stabilization, which can be achieved through cross-linking. In this study, qualitative and quantitative Fourier transform infrared (FTIR) analyses were used to assess dentin collagen stabilization effects of three structurally-different flavonoids —A-type linkage proanthocyanidins (A-PA), B-type linkage proanthocyanidins (B-PA), and epigallocatechin gallate (EGCG), all from natural extracts. Particularly, transmission FTIR spectroscopy was used for the first time to quantitatively assess the biodegradation of fresh ultra-thin (10 µm) dentin collagen films caused by collagenase digestion. Two traditional analytical methods, namely the hydroxyproline assay and weight loss analysis, were also used for comparison purposes. The results from all three methods showed consistently that A-PA and B-PA provide better collagen stabilization than EGCG at concentrations of 0.65% and 1.3% (p<0.01). FTIR is demonstrated to be a valuable and reliable analytical tool for qualitative and quantitative evaluation of ultra-thin collagen films.

This study investigated the effect of ultrasound application when luting ceramic using two preheated composites that show distinct responses to preheating at 69°C: Filtek Z100 and Z350XT. RelyX Veneer was the control. Feldspar disks were luted using the resin-based luting agents (RBLAs), and ultrasound was tested. Biaxial flexure strength (σ_bf) was calculated at z-axial positions of the luted disks (z=0; z=−t₂). Microtensile bond strength (μTBS) to ceramic was tested (n=30). Data were analyzed at α=0.05. At z=0, the σ_bf was higher for Z350 when ultrasound was not used. When ultrasound was applied, the σ_bf was similar between Z350 and Z100. At z=−t₂, differences across the RBLAs were observed: Z350 was superior than Z100 and control without ultrasound. Ultrasound increased σ_bf for Z100 at both axial positions. The preheated composites yielded higher μTBS than the control. Ultrasonication increased the mechanical performance of ceramic luted with Z100 without influencing the film thickness.

Pure titanium is widely used as a material in dental implants. However, it possesses inferior mechanical strength. This study aimed to elucidate the efficacy of acid treated multi-directionally forged (MDF) pure titanium in vivo. We verified the temporal changes until osseointegration in beagle dogs. Using two types of experimental materials (conventional pure titanium or MDF pure titanium), new bone formation was assessed using morphological examinations, and the bone-to-implant contact (BIC) value was evaluated at each time point (14, 30, and 90 days after the operation). As such, new bone formation was observed around the acid-etched MDF group, in which the BIC value was highest, followed by that in the acid-etched pure titanium group. MDF pure titanium implants showed early promotion of new bone formation compared to conventional titanium implants. The new acid-treated MDF made of pure titanium could be applied to humans in the future to prove its practicality.

To evaluate the fracture resistance of computer-aided design and computer-assisted manufacturing restorations as the abutment of removable partial dentures, experimental blocks, with the rest seat made of feldspar, hybrid resin composite, lithium disilicate glass ceramic, or zirconia, were subjected to loading by a metallic occlusal rest. The rest contacted the rest seat with an accurate fit and two mismatch contact conditions: bottom and sidewall contact. Zirconia exhibited the highest fracture load, and the fracture load of the accurate fit was significantly higher than that of the sidewall contact (p<0.05) and insignificantly higher than that of the bottom contact (p>0.05). A finite element analysis of the sidewall contact revealed a higher tensile stress concentration at the bottom of the rest seat than the other contact conditions. The mismatch between the rest and the restoration reduced fracture resistance, while zirconia as the abutment withstood the average occlusal force of the posterior region.

The aim of this study was to evaluate the crosslinking effect of the radio-frequency atmospheric-pressure glow discharge (RF-APGD) plasma jet treatment on dentin collagen. The dentin collagen was treated by an RF-APGD plasma jet with the gas temperature of 4°C under different treatment times, while the control was a non-treatment group. The dentin collagen was characterized in terms of atomic force microscopy-based nanoindentation, differential scanning calorimeter, Raman analysis and X-ray photoelectron spectroscopy (XPS) measurement. The crosslinking effect of the plasma-treated dentin collagen was found compared to that of the control group. The elastic modulus and denaturation temperature of the dentin collagen after plasma treatment for 30 s were significantly higher than those in the control group (p<0.05). The RF-APGD plasma jet treatment can promote the crosslinking of the dentin collagen, which is of great significance to improve its mechanical and thermal stabilities.

The study was done to compare cell viability between ES-D3 and Balb/c 3T3 cells, and evaluate the difference in cell viability between these cell lines using denture-base lining materials for prosthetic dentistry. To compare the cytotoxicity, three acrylic and three silicone dental materials were used. The cell viability was examined by MTT and lactate dehydrogenase (LDH) methods. The cell viability immediately after malaxation or light irradiation was lower only for the acrylic materials in 3T3 cells, and for both silicone and acrylic materials in ES-D3 cells. However, the cell viability determined 24 h after malaxation or light irradiation by the MTT and LDH methods did not significantly differ between samples. It was observed that ES-D3 cells are more sensitive depending on the type of material. The results suggest that ES-D3 cells can be used as in vitro systems for conducting biosafety assessment to predict embryotoxicity.

Advancements in dental cements have considerably improved their bond strengths. However, high bond strength often makes the removal of restorations difficult. Thus, smart dental cements that show controllable bond strength are required. A conventional resin-modified glass-ionomer-cement demonstrated a significant reduction in the bond strength after current application. However, for this system, the ions in the cement are released into the oral cavity, resulting in a reduction of the electrical conductivity and in losses of the expected on-demand debonding property. Herein, the effects of immersion in 0.9 and 15% NaCl solutions on the electrical conductivity and debonding properties were investigated. The cement immersed in 0.9% NaCl solution from 1 to 28 days maintained similar bond strength reductions after current application, whereas that in 15% NaCl solution initially showed no bond strength reduction after 1 day but exhibited an increase in the bond strength reduction after immersion for 28 days.

Resin blocks and ceramic blocks for CAD/CAM crowns were cut into powders and separated into three particle size groups. Oxidative stress and cell viability were measured in 3T3 and FRSK cells. The results of cytotoxicity tended to be slightly higher for resin than for ceramics. The values also increased as the particle size decreased in the powders. In addition, incorporation into cells was frequently observed under SEM, suggesting that the particle size of easily incorporated dust is different among cell types. Fluorescence-activated cell sorter (FACS) showed an increase in apoptosis and a decrease in cell viability in most of the sample groups compared to the control group. Hematoxylin and eosin staining of the cells showed deep staining of the nuclei in the sample groups. It was found that oxidative stress cell viability and apoptosis appeared differently depending on the size of the particles and the type of cells.