Tetsu-to-Hagane
Online ISSN : 1883-2954
Print ISSN : 0021-1575
ISSN-L : 0021-1575
Search
Advanced search
OR
Browse
Search
Volume 74, Issue 11
Displaying 1-20 of 20 articles from this issue
Show all abstracts
    • |<
    • <
    • 1
    • >
    • >|
  • Current Status of Researches on Metallic New Materials
    Ryuichi NAKAGAWA
    1988 Volume 74 Issue 11 Pages 2061-2066
    Published: November 01, 1988
    Released on J-STAGE: May 29, 2009
    DOIhttps://doi.org/10.2355/tetsutohagane1955.74.11_2061
    JOURNAL FREE ACCESS
    Download PDF (2762K)
  • Machine Condition Diagnosis Technique for Rolling Mills and Processing Lines
    Hiroto OKITU
    1988 Volume 74 Issue 11 Pages 2067-2079
    Published: November 01, 1988
    Released on J-STAGE: May 29, 2009
    DOIhttps://doi.org/10.2355/tetsutohagane1955.74.11_2067
    JOURNAL FREE ACCESS
    Download PDF (3327K)
  • New Development of Thorium Molten-Salt Reactor System
    Kazuo FURUKAWA
    1988 Volume 74 Issue 11 Pages 2080-2089
    Published: November 01, 1988
    Released on J-STAGE: May 29, 2009
    DOIhttps://doi.org/10.2355/tetsutohagane1955.74.11_2080
    JOURNAL FREE ACCESS
    Show abstractHide abstract
    [in Japanese]
    View full abstract
    Download PDF (1791K)
  • Effect of MgO Added with SiO2 or Al2O3 on the Reduction of Dense Wustite with H2
    Nobukazu SHIGEMATSU, Hikoya IWAI
    1988 Volume 74 Issue 11 Pages 2090-2097
    Published: November 01, 1988
    Released on J-STAGE: May 29, 2009
    DOIhttps://doi.org/10.2355/tetsutohagane1955.74.11_2090
    JOURNAL FREE ACCESS
    Show abstractHide abstract
    The dense wustite plates containing MgO with SiO2 or Al2O3 were reduced isothermally in H2 gas stream over a temperature range of 670 to 930°C.
    By the presence of very small of SiO2 dissolved in wusuite phase the reduction reaction was promoted at temperatures above 800°C and retarded at temperatures below 730°C. MgO dissolved in FeO with SiO2 cancels the effect of SiO2 mentioned above.
    Al2O3 dissolved in wustite slows down the reduction in initial stage greatly and that in and after middle stage further more. MgO dissolved in wustite with Al2O3 slows down the reduction in the initial stage further.
    Correspondence between reduction rate and structure of reduced iron recognized in this work is same as that in previous works.
    View full abstract
    Download PDF (5584K)
  • Reduction of Wustite Pellets with H2-CO-CO2 and H2-CO2 Gas Mixtures
    Takeaki MURAYAMA, Chong Min CHO, Koichiro HIGASHI, Yoichi ONO
    1988 Volume 74 Issue 11 Pages 2098-2105
    Published: November 01, 1988
    Released on J-STAGE: May 29, 2009
    DOIhttps://doi.org/10.2355/tetsutohagane1955.74.11_2098
    JOURNAL FREE ACCESS
    Show abstractHide abstract
    The applicability of the reduction model proposed in the previous paper (Tetsu-to-Hagané, 73 (1987), p. 972), in which the water-gas shift reaction and multi-component gas diffusion were taken into account, to the reduction kinetics of wustite pellets with H2-CO-CO2 and H2-CO2 gas mixtures was examined. The gas composition was such that the reduction was possible to take place not with CO-CO2 but only with H2. In the calculation, the parameters included in the model were modified depending on the gas composition by using the method proposed in the previous paper.
    The following results were obtained;
    1) The reduction curves calculated by the model agreed well with the observed data except the case of lower H2 concentration.
    2) The effect of the water-gas shift reaction was not so significant on the reduction curves, but it was remarkable on the mass transfer rate of each component of gas mixture.
    3) Depending on the reduction condition, especially at higher H2 concentration, CO/CO2 ratio in the pellet increased because of the water-gas shift reaction. As a result, the reduction of wustite with CO took place instead of the oxidation of reduced iron with CO2.
    View full abstract
    Download PDF (1143K)
  • Flow Phenomena and Heat Transfer Around a Sphere Submerged in Water Jet and Bubbling Jet
    Manabu IGUCHI, Jun-ichi TANI, Tomomasa UEMURA
    1988 Volume 74 Issue 11 Pages 2106-2113
    Published: November 01, 1988
    Released on J-STAGE: May 29, 2009
    DOIhttps://doi.org/10.2355/tetsutohagane1955.74.11_2106
    JOURNAL FREE ACCESS
    Show abstractHide abstract
    Velocity and turbulence around a sphere made of synthetic resin submerged in water and bubbling jets in a cylindrical vessel with bottom blowing were measured by making use of LDV. The melting process of an ice sphere was recorded by video camera. The local Nusselt number Nuθ of the ice sphere was determined from the initial change of the local radius. The mean Nusselt number Nu was calculated from Nuθ by numerical integration over the surface of the sphere. The effects of velocity and turbulence intensity on Nuθ and Nu were investigated. An empirical expression for Nu was proposed as a function of Reynolds number and turbulence intensity. A method of predicting the complete melting time of an ice sphere was presented.
    View full abstract
    Download PDF (1208K)
  • Rate of Reduction of TiO2 in CaO-SiO2-Al2O3-TiO2 Slags by Carbon-saturated Iron Melt
    Haiping SUN, Nobuya SHINOZAKI, Katsumi MORI, Yasuji KAWAI
    1988 Volume 74 Issue 11 Pages 2114-2121
    Published: November 01, 1988
    Released on J-STAGE: May 29, 2009
    DOIhttps://doi.org/10.2355/tetsutohagane1955.74.11_2114
    JOURNAL FREE ACCESS
    Show abstractHide abstract
    Reduction rate of TiO2 in CaO-SiO2-Al2O3-TiO2 slags by carbon dissolved in iron melts was investigated at 1 350°C 1 600°C under argon atmosphere. It was found that the reduction of TiO2 proceeded simultaneusly with the reduction of SiO2 and was promoted by the addition of silicon to the initial iron melts. For acid slags, the reduction rate of TiO2 decreased with inceasing ratio of CaO/SiO2, whereas it slightly increased for slags with CaO/SiO2>1.
    The kinetic analysis on the basis of the two film theory showed that the overall rate of transfer of Ti from slag to metal phases was controlled by the rate of chemical reactions at the interface for cases without silicon addition, but it was found that the resistance to transfer of TiO2 in the diffusion boundary layer at slag could not be neglected when some amount of silicon was added to the metal.
    View full abstract
    Download PDF (2918K)
  • Computer Control of Electric Arc Furnace Steelmaking Process Based on a Mathematical Model
    Takeshi TAKAWA, Jun INOUE, Haruo YAMAMURA
    1988 Volume 74 Issue 11 Pages 2122-2129
    Published: November 01, 1988
    Released on J-STAGE: May 29, 2009
    DOIhttps://doi.org/10.2355/tetsutohagane1955.74.11_2122
    JOURNAL FREE ACCESS
    Show abstractHide abstract
    For the computer control of steelmaking process in electric arc furnace, a simplified mathematical model suitable for online application has been developed on the following procedure.
    (1) An equation for judging the meltdown of scrap accurately by monitoring the position of electrodes and the furnace wall temperature throughout the melting stage has been developed.
    (2) Equations for estimating decarburization and temperature increase in consideration of the decarburizing characteristics in oxygen blowing period, and equations for estimating molten steel temperature change and composition change in the period of temperature adjustment and tapping on the basis of heat and material balances have been developed.
    (3) Based on these equations in the refining stage, the authors have developed control models calculating the amount of blown oxygen, electric power and ferroalloys requisite for the operation.
    At EAF shop in Osaka Steel Works, the models are in use for the computer control and contribute to the reduction of power consumption and so on.
    View full abstract
    Download PDF (1202K)
  • Initial Solidification Analysis in the Vicinity of Meniscus in Continuous Casting Mold
    Takeshi TAKAWA, Tsutomu TAKAMOTO, Hiroshi TOMONO, Ken'ichi TADA
    1988 Volume 74 Issue 11 Pages 2130-2136
    Published: November 01, 1988
    Released on J-STAGE: May 29, 2009
    DOIhttps://doi.org/10.2355/tetsutohagane1955.74.11_2130
    JOURNAL FREE ACCESS
    Show abstractHide abstract
    For the improvement of surface quality of continuously cast steel, an analysis model taking into consideration of steel casting has been developed on the following procedure in order to explain initial solidification phenomenon in the vicinity of meniscus.
    (1) A calculation method of temperature distribution has been worked out, assuming that a small quantity of new molten steel flows into mold intermittently and solidified shell and molten steel are casted vertically to the horizontal direction.
    (2) Direct difference method using inner nodal point is applied to the numerical calculation of heat transfer equation so that the movement of molten steel due to casting can be easily dealt with, and four kinds of equations are made according to the boundary condition as the fundamental equations in divided mesh.
    By using this model, it becomes possible to estimate the temperature distribution in steady-state under casting. In this study, the solidified shell, slag rim shape and the temperature distribution in mold area in the case of using the ordinary copper mold are estimated. Furthermore the adiabatic effect in the case of using mild cooling mold containing refractory is evaluated quantitatively.
    View full abstract
    Download PDF (979K)
  • Development of a Shear Line Including a New Type of Combination Leveller with Tension Device
    Takeshi MASUI, Kiyoharu WATANABE, Hirofumi NAGANO, Yasukazu IGARASHI
    1988 Volume 74 Issue 11 Pages 2137-2144
    Published: November 01, 1988
    Released on J-STAGE: May 29, 2009
    DOIhttps://doi.org/10.2355/tetsutohagane1955.74.11_2137
    JOURNAL FREE ACCESS
    Show abstractHide abstract
    Recently, the demand of customers for the flatness of cold strip becomes more and more strict. Therefore the effective shape correction device has been desired in a shear line for replacement of a conventional roller leveller.
    Introducing tension leveller on the upstream of a shear line is probably a reliable answer, but its investment cost is large and extra space is necessary.
    To solve this problem a new type of compact combination leveller was designed based on the theoretical analysis and experiments.
    This consisted of non-drive stretch leveller, main leveller and double pinch rolls. Then it was introduced in a shear line. Using this combination leveller, the strip is elongated by repeated bending under superposed tension of pay off reel tension and idle leveller drawing force. Friction force of main leveller and pinch rolls causes this drawing force. The strip of satisfactory flatness almost the same as that by tension leveller can be obtained.
    This new shear line was first constructed in 1986 and has been working successfully. Now the same type combination levellers are under designing and construction.
    View full abstract
    Download PDF (8316K)
  • Superplastic Warm-die and Pack Forging of Nickel-base Superalloy Powder
    Yasunori TORISAKA, Masahito KATOH, Matsuo MIYAGAWA
    1988 Volume 74 Issue 11 Pages 2145-2152
    Published: November 01, 1988
    Released on J-STAGE: May 29, 2009
    DOIhttps://doi.org/10.2355/tetsutohagane1955.74.11_2145
    JOURNAL FREE ACCESS
    Show abstractHide abstract
    In the Gatorizing process, extrusion is needed to obtain a fine recrystallized structure. Because of the bottle-neck of the extrusion, however, a largesized disks have not yet been formed. Therefore, it is desirable to develop a new work processing excluding extrusion and applicable to form large disks. In the present study, it was discussed whether the application of superplastic warm-die and pack forging to Ni-base superalloy Mod. IN-100 atomized powder is appropriate or not. Namely, billets, which were a cylindrical case made of carbon steel or austenitic stainless steel and packed with the powder, were heated to 1 100°C and then superplastically forged at a strain rate of 1.8 × 10 -2 s -1 using dies made of Inconel 713C and pre-heated at about 600°C. A desirable forming was performed using a thick walled case made of austenitic stainless steel.
    View full abstract
    Download PDF (5481K)
  • Relation between Hardenability and Segregation to Austenite Grain Boundaries of Boron Atom on Direct Quenching Process
    Yoshihiko KAMADA, Hirofumi KURAYASU, Seiichi WATANABE
    1988 Volume 74 Issue 11 Pages 2153-2160
    Published: November 01, 1988
    Released on J-STAGE: May 07, 2010
    DOIhttps://doi.org/10.2355/tetsutohagane1955.74.11_2153
    JOURNAL FREE ACCESS
    Show abstractHide abstract
    The effect of boron (B) on hardenability is explained by the decrease of boundary energy due to the segregation of B atoms to austenite grain boundaries. In this paper, the effect of niobium (Nb) on hardenability of B treated direct quenching steel is studied with varing the condition of B segregation to austenite boundaries. And it is clarified that the effect of B on hardenability is fully obtained even at unrecrystallized state of austenite, and that the maximum hardenability in direct quenching process can be attained at about 10 ppm soluble B which is about three times as the optimum ones of conventional reheat quenching process. It is concluded that the addition of 0.015% Nb rather give rise to the hardenability of B even in unrecrystallized state of austenite in direct quenching process because Nb hinders boundary migration of austenite and enables soluble B to segregate to the grain boundaries and deformation bands.
    View full abstract
    Download PDF (5284K)
  • Strength and Toughness of Cold-rolled 32Mn-7 Cr Steel at Cryogenic Temperatures
    Tetsumi YURI, Kotobu NAGAI, Keisuke ISHIKAWA
    1988 Volume 74 Issue 11 Pages 2161-2168
    Published: November 01, 1988
    Released on J-STAGE: May 29, 2009
    DOIhttps://doi.org/10.2355/tetsutohagane1955.74.11_2161
    JOURNAL FREE ACCESS
    Show abstractHide abstract
    The effects of cold-rolling on strength and toughness at 4K were investigated for a high manganese steel, 32Mn-7Cr steel. The yield strength at 4K was 1118MPa for the unrolled steel and was increased to 1379MPa and 1786MPa for the 20 and 40% cold-rolled steels, respectively. However, the elongation and the reduction of area were decreased with an increase in reduction ratio. Especially, the elongation was significantly decreased. The Charpy absorbed energy and the fracture toughness were also decreased markedly. The decrease in toughness by cold-rolling was due to the formation of subcrack and "flat brittle facet" in the fractured surface. The subcrack was caused by intergranular failure, and the flat brittle facet is believed to be produced mainly by intergranular failure and partly by twin boundary failure.
    View full abstract
    Download PDF (4844K)
  • The Effect of Microstructure on Fracture Toughness of Ti-6Al-2Sn-4Zr-2Mo Alloy
    Tsutomu OKA, Yoshiharu MAE, Teruo KISHI
    1988 Volume 74 Issue 11 Pages 2169-2176
    Published: November 01, 1988
    Released on J-STAGE: May 29, 2009
    DOIhttps://doi.org/10.2355/tetsutohagane1955.74.11_2169
    JOURNAL FREE ACCESS
    Show abstractHide abstract
    The effect of microstructure on fracture toughness of near α titanium alloy Ti-6Al-2Sn-4Zr-2Mo was investigated by Acoustic Emission three dimensional location, Acoustic Emission source characterization and fractography method. The fracture toughness of alloy with acicular α structure was superior to that of alloy with equiaxed α structure at the same yield strength level. It was considered that the result was based on the number of large amplitude Acoustic Emission events prior to KIC and on the deflection of the crack path. The large amplitude Acoustic Emission events coresponded to microcracks of 50-80μm which nucleated at the pre-fatigue crack tip along crack front in both structures. Macroscopic crack growth occured where these microcracks coalesced in the direction to specimen thickness. These microcracks lower the stress concentration at the crack tip. Thus it was concluded that microcrackings enhanced the fracture toughness of titanium alloy with acicular α structure.
    View full abstract
    Download PDF (6038K)
  • TiN Film Formation on a 1%C-5%Cr Roll Steel by Ion Beam Implanted Vapor Deposition and the Resulting Improvement of the Wear Resistance
    Hiroshige WANAKA, Tatsumi KIMURA, Junichi SHIMOMURA, Syuzo UEDA, Mamor ...
    1988 Volume 74 Issue 11 Pages 2177-2184
    Published: November 01, 1988
    Released on J-STAGE: May 29, 2009
    DOIhttps://doi.org/10.2355/tetsutohagane1955.74.11_2177
    JOURNAL FREE ACCESS
    Show abstractHide abstract
    The metallurgical structure and wear resistance of TiN film formed on 1%C-5%Cr roll steel specimens by Ti vapor deposition with N ions implantation were studied. The main results obtained are as follows: 1) The color of film varies depending on the evaporation rate of Ti and the electric current density of N ions. 2) The X-ray photoelectron spectroscopic (XPS) investigation detected TiN in the golden film and metallic Ti and TiO2 in the silver film. 3) Measurements using a scanning electron microscope (SEM) with energy dispersive X-ray indicated that the concentration of Ti and Fe varies over the distance of a few hundred nm in the boundary zone between the base metal and the coated film. 4) The adhesion of golden film is better than that of silver one. 5) The two-cylinder-type wear resistance test results showed that the golden TiN film significantly improves wear resistance of 1%C-5%Cr roll steel.
    View full abstract
    Download PDF (3066K)
  • Effect of Carburizing Helium Environment on Creep Behavior of Ni-base Heat-resistant Alloys for High-temperature Gas-cooled Reactors
    Yuji KURATA, Yutaka OGAWA, Hajime NAKAJIMA
    1988 Volume 74 Issue 11 Pages 2185-2192
    Published: November 01, 1988
    Released on J-STAGE: May 29, 2009
    DOIhttps://doi.org/10.2355/tetsutohagane1955.74.11_2185
    JOURNAL FREE ACCESS
    Show abstractHide abstract
    Creep tests were conducted on Ni-base heat-resistant alloys Hastelloy XR and XR-II, i. e. versions of Hastelloy X modified for nuclear applications, at 950°C using four types of helium environment with different impurity compositions, and mainly the effect of carburization was examined.
    For all the materials tested, the values of creep rupture time obtained under the carburizing conditions were similar to or longer than those in the commonly used, standard test environment (JAERI Type B helium). The difference among the results was interpreted by the counterbalancing effects of the strengthening due to carburization and possible weakening caused under very low oxidizing potential. In the corrosion monitoring specimens pronounced carbon pick-up was observed in the environment with high carbon activity and very low oxidizing potential. Based on the results obtained in the present and the previous works, it is suggested that a moderate control of the impurity chemistry is important rather than simple purification of the coolant in protecting the material from the environment-enhanced degradation. Either condition with high or low extremes in the oxidizing and carburizing potentials may cause enhanced degradation and thus are desirable to be avoided at the elevated temperatures.
    View full abstract
    Download PDF (1206K)
  • Development of a Nickel-base Single Crystal Superalloy Containing Molybdenum by an Alloy Designing Method
    Takehiro OHNO, Rikizo WATANABE, Kohichi TANAKA
    1988 Volume 74 Issue 11 Pages 2193-2200
    Published: November 01, 1988
    Released on J-STAGE: May 29, 2009
    DOIhttps://doi.org/10.2355/tetsutohagane1955.74.11_2193
    JOURNAL FREE ACCESS
    Show abstractHide abstract
    A new nickle-base single crystal superslloy was developed by applying an "alloy designing" method, which was originated by Watanabe and improved by a group of the National Research Institute of Metals (NRIM). The typical composition range was 6-7 %Cr, 5-6 %Al, 5-8 %W, 5-8 %Ta and 4-6 %Mo (mass%). This alloy had more stable microstructure and higher creep rupture strength than single crystal superalloys so far developed. The basic flow of the designing was as follows. First, the composition of γ and γ' phases and the volume fraction of γ'phase were determined according to the NRIM scheme varying the combination of molar percentages of tungsten, tantalum and molybdenum included in γ' phase. Second, the most desirable combination of γ and γ' couples were selected to maximize the summed values of γ and γ' lattice constants and minimize the misfit between γ and γ' phases. Third, the stability of γ phase during solution heat treatment was assesed by introducing a new parameter of "Solubility Limit Index", whose value was defined by the solubility of included elements into nickel matrix.
    View full abstract
    Download PDF (4734K)
  • Equilibrium and Non-equilibrium Grain Boundary Segregation Behavior of Phosphorus and Carbon in Austenitic Region of Steel
    Takashi ABE, Koshiro TSUKADA, Hisatoshi TAGAWA, Isao KOZASU
    1988 Volume 74 Issue 11 Pages 2201-2208
    Published: November 01, 1988
    Released on J-STAGE: May 29, 2009
    DOIhttps://doi.org/10.2355/tetsutohagane1955.74.11_2201
    JOURNAL FREE ACCESS
    Show abstractHide abstract
    Auger electron microscopic analyses were performed to clarify the grain boundary segregation behavior of phosphorus and carbon in the austenitic region of steel. Grain boundary migration during grain growth and recrystallization gave rise to non-equilibrium segregation which resulted in a higher solute concentration on grain boundaries than that of equilibrium segregation. The increment of segregation caused by migration depended on the boundary migration velocity. Faster migration brought about greater concentrations for velocities less than a critical value, which depended on the diffusivity of solute. In recrystallization, faster diffusing elements such as carbon segregated with higher concentrations. It was suggested that the solute sweep effect during grain boundary migration caused the non-equilibrium segregation.
    View full abstract
    Download PDF (5275K)
  • Tensile Test of Coke Piece/Thermodynamics of Fe-Cr-C Alloy in Equilibrium with Solid Chromite
    Jun FUKAI, Toshiyuki HASHIDA, Kazuya SUZUKI, Takatoshi MIURA, Shigemor ...
    1988 Volume 74 Issue 11 Pages 2209-2214
    Published: November 01, 1988
    Released on J-STAGE: May 29, 2009
    DOIhttps://doi.org/10.2355/tetsutohagane1955.74.11_2209
    JOURNAL FREE ACCESS
    Download PDF (1006K)
  • [title in Japanese]
    [in Japanese]
    1988 Volume 74 Issue 11 Pages 2221-2222
    Published: November 01, 1988
    Released on J-STAGE: May 29, 2009
    DOIhttps://doi.org/10.2355/tetsutohagane1955.74.11_2221
    JOURNAL FREE ACCESS
    Download PDF (403K)
    • |<
    • <
    • 1
    • >
    • >|
feedback
 Top