In this paper, the scattering far-field from a circular electric conducting cylinder has been analyzed by physical optics (PO) approximation for both H and E polarizations. The evaluation of radiation integrations due to the PO current is conducted numerically and analytically. While non-uniform and uniform asymptotic solutions have been derived by the saddle point method, a separate approximation has been made for forward scattering direction. Comparisons among our approximation, direct numerical integration and exact solution results yield a good agreement for electrically large cylinders.
Volume integral equations combined with orthogonality of guided mode and non-guided field are proposed for the TE incidence of two-dimensional optical slab waveguide. The slab waveguide is assumed to satisfy the single mode condition. The formulation of the integral equations are described in detail. The matrix equation obtained by applying the method of moments to the integral equations is shown. Numerical results for step, gap, and grating waveguides are given. They are compared to published papers to validate the proposed method.
To achieve smooth beam injection in operation of synchrotron radiation facilities, pulsed multipole magnet beam injectors are developed. It is found that the developed beam injector causes serious disturbance in the circulating storage beam in the Aichi synchrotron radiation center, and that such the unexpected disturbance of the storage beam may be caused by eddy current induced on thin titanium coating inside a beam duct. In this work, the induced eddy current on the titanium layer is evaluated quantitatively by numerical simulations and improvement for the developed beam injector is discussed based on the numerical simulation.
In our previous paper, we have proposed a new numerical technique for transient scattering problem of periodically arrayed dispersion media by using a combination of the fast inversion Laplace transform (FILT) method and Fourier series expansion method (FSEM), and analyzed the pulse response for several widths of the dispersion media or rectangular cavities. From the numerical results, we examined the influence of a periodically arrayed dispersion media with a rectangular cavity on the pulse response. In this paper, we analyzed the transient scattering problem for the case of dispersion media with slanted air regions by utilizing a combination of the FILT, FSEM, and multilayer division method (MDM), and investigated an influence for the slanted angle of an air region. In addition, we verified the computational accuracy for term of the MDM and truncation mode number of the electromagnetic fields.
A periodic array of InSb spheres on a substrate is numerically analyzed at terahertz frequencies. The incident field is shown to be coupled to the substrate due to the guided-mode resonance. The effect of the background refractive index on the transmission characteristics is investigated for sensor applications.
A novel jig structure for S11 calibration with short/open conditions and one reference material (referred to here as SOM) in dielectric measurement of liquids using a coaxial feed type stepped cut-off circular waveguide and a formula for exact calculation of S11 for the analytical model of the structure using the method of moments (MoM) was proposed. The accuracy and validity of S11 values calculated using the relevant formula was then verified for frequencies of 0.50, 1.5 and 3.0 GHz, and S11 measurement accuracy with each termination condition was verified after calibration with SOM by combining the jig of the proposed structure with the study's electromagnetic (EM) analysis method. The relative complex permittivity was then estimated from S11 values measured with various liquids in the jig after calibration, and differences in results obtained with the proposed method and the conventional jig, the analytical model and the EM analysis method were examined. The validity of the proposed dielectric measurement method based on a combination of the above jig structure, numerical S11 calculation and the calibration method was thus confirmed.
This paper proposes a methodology for designing broadband class B/J power amplifier based on a mirrored lowpass filter matching structure. According to this filter theory, the impedance of this design method is mainly related to the cutoff frequency. Series inductors and shunt capacitors filter out high frequencies. The change of input impedance with frequency is small in the passband. Which can suppress higher harmonics and expand bandwidth. In order to confirm the validity of the design method, a broadband high-efficiency power amplifier in the 1.3 - 3.9GHz band is designed and fabricated. Measurement results show that the output power is greater than 40.5dBm, drain efficiency is 61.2% - 70.8% and the gain is greater than 10dB.