精密機械

航空機用転輪羅針儀について

富沢豁

1954 年 20 巻 233 号 p. 279-284
発行日: 1954/08/05
公開日: 2009/06/30

DOIhttps://doi.org/10.2493/jjspe1933.20.279

ジャーナルフリー

PDF形式でダウンロード (1018K)
大型歯車用簡易歯形検査機について

会田俊夫, 寺内喜男, 平松誠

1954 年 20 巻 233 号 p. 285-291
発行日: 1954/08/05
公開日: 2009/06/30

DOIhttps://doi.org/10.2493/jjspe1933.20.285

ジャーナルフリー

抄録を表示する抄録を非表示にする

The authors designed a new simple involute curve tester for large spur and helical gears. This tester measures the differences between the gear tooth curve and the circular arc in the section perpendicular to the gear shaft.
These differences between the true involute curve and the circular arc, and the expected errors induced by the disposition of centre of the circular arc are calculated and the range of adoption of the curve tester of this type was determined.
Some records as examples were also given with the comments on them.

抄録全体を表示

PDF形式でダウンロード (1128K)
薄板の剪勢断試験

斎藤博

1954 年 20 巻 233 号 p. 291-296
発行日: 1954/08/05
公開日: 2010/02/16

DOIhttps://doi.org/10.2493/jjspe1933.20.291

ジャーナルフリー

抄録を表示する抄録を非表示にする

In the study of this shearing test, Amsler testing machine, three kinds of round shearing tools of 10mm, 25mm and 50mm in diameter respectively and autographic recorder are employed.The autographic recording system consists of dial gauge with thin disc having fifty slits, photocell, photo-electric-current amplifier with relay, electromagnet with ratchet attached to Amsler recording drum. By these apparatus, approximate shearing curves of round blank are recorded on the drum. The test pieces are of mild steel sheet of 0.96mm in thickness.
The results are as follows.
1) Nominal shearing stress decreases gradually in proportion to the increase of the tool clearance.
2) Nominal shearing stress is 7580% of ultimate tensile strength.
3) The Minimum values of the specific work required in each tool being about 12kg-mm/mm², appear between 8 and 16% tool clearance,
4) And others.

抄録全体を表示

PDF形式でダウンロード (1073K)
仕上面加工層に関する研究(第2報)

精密仕上面の加工層

浅枝敏夫, 小野浩二

1954 年 20 巻 233 号 p. 297-300
発行日: 1954/08/05
公開日: 2009/06/30

DOIhttps://doi.org/10.2493/jjspe1933.20.297

ジャーナルフリー

抄録を表示する抄録を非表示にする

Quenched carbon steel (0.63%C) test pieces were finished by such various methods as grinding, lapping, superfinishing, supergrinding, emery-paper polishing and electropolishing. The depth of the surface layers of the test pieces thus finished was measured by etching method explained in detail in the first report.
It was confirmed that these surface layers were considerably deeper than we expected, due to the existence of residual surface layers produced by previous finishing (grinding).
The depth of surface layer produced only by the final finishing process can be measured by removing those produced in the previous finishing process.
The results are as follows:
Medium and fine grinding: 7μ and 2.5μ, lapping: 2μ, superfinishing: 1μ.

抄録全体を表示

PDF形式でダウンロード (501K)
空気マイクロメータを利用した切削工具動力計

プラスチックスの研削切断法の研究第3報

小林昭

1954 年 20 巻 233 号 p. 301-306
発行日: 1954/08/05
公開日: 2010/05/07

DOIhttps://doi.org/10.2493/jjspe1933.20.301

ジャーナルフリー

抄録を表示する抄録を非表示にする

A tool dynamometer, which consists of a pair of parallel springs attached to the cutting tool or work and a pneumatic micrometer, is described here. The minute displacement of the former proportional to the cutting force is detected by the latter.
In this paper the following items are involved:
1) Static and dynamic characteristics and measuring force (force due to air jet from the nozzle) of pneumatic micrometer (water column type).
2) Static and dynamic characteristics of parallel springs.
3) Some practical applications: dynamometer for shaping, turning, milling, cutting-off, scratch tests or lapping force, etc., with photograrns.
This dynamometer is not only able to measure the mean cutting force simply and accurately in machine shops, but also to record the instant changes of force in laboratory.

抄録全体を表示

PDF形式でダウンロード (1539K)
表面あらさ測定に関する統計的研究(第5報)

表面粗さの性質を示すスケール

本田肇

1954 年 20 巻 233 号 p. 307-310
発行日: 1954/08/05
公開日: 2009/06/30

DOIhttps://doi.org/10.2493/jjspe1933.20.307

ジャーナルフリー

抄録を表示する抄録を非表示にする

The characteristic of the surface can be explained by the statistic R/s, (max. range)/(standard deviation).
All surfaces are not of equal characteristic, even though their "peak-to-valley heights " are equal. From the statistic R/s, one can see how the surface is flat or notched.
The effect of electro-polishing to the smoothness of surface is represented by R/s, and it was shown quantitatively.
The reason that the tracer instruments for measuring surface roughness are not available in the case of soft surface is shown quantitatively, and it is proved statistically.

抄録全体を表示

PDF形式でダウンロード (616K)
光沢(I)

筒井俊正

1954 年 20 巻 233 号 p. 311-314
発行日: 1954/08/05
公開日: 2010/02/16

DOIhttps://doi.org/10.2493/jjspe1933.20.311

ジャーナルフリー

抄録を表示する抄録を非表示にする

昭和28年度精機学会光沢專門委員会及びその後の光沢委員会では光沢に関する研究,文献,規格等について検討し漠然たる光沢を物理的の量にて表現する方法を研究し,塗料,紙,プラスチックス,硝子,金属等の光沢を測定するに適当した光沢度計を試作し,光沢に関する規格を設定したいと考えている。本会の溝成は次の様である。
富士写真フイルム藤沢信
東大工蓮沼宏,倉藤尚雄,筒井俊正(委員長)
電気試験所今中治,小林昭
小坂研究所小坂誠市郎,
プラスチックス協会小山寿
日本ペイント村沢正信
印刷庁研究所中西篤
旭ガラス佐藤成男
東大文高木貞二
本報告は本会の行つた研究の一部分であり未完成の研究ではあるが中間報告として提出する。

抄録全体を表示

PDF形式でダウンロード (415K)
特許紹介

1954 年 20 巻 233 号 p. 320-321
発行日: 1954/08/05
公開日: 2009/06/30

DOIhttps://doi.org/10.2493/jjspe1933.20.320

ジャーナルフリー

PDF形式でダウンロード (453K)