巻号一覧
後続誌
33 巻, 394 号
選択された号の論文の10件中1～10を表示しています
- |<
- <
- 1
- >
- >|
-
歌川 正博, 山本 真司1967 年 33 巻 394 号 p. 695-701
発行日: 1967/11/05
公開日: 2010/02/16
ジャーナル フリーPDF形式でダウンロード (1423K) -
武野 仲勝, 中村 峯雄1967 年 33 巻 394 号 p. 702-708
発行日: 1967/11/05
公開日: 2009/06/30
ジャーナル フリーA new internal grinding machine has been designed to obtain very high accuracy in automatic sizing grinding. Hydraulic systems employed in ordinary grinder as power transmission and control system are completely removed, The wheel head oscillating mechanism is driven by constant speed cam ane link for traversing grinding, the wheel head is infed by cam and the internal grinding spindle is driven by high frequency motor. This internal grinder realized the sufficiently small piece-to-piece fluctuation and the very slow deviation from set value in dimentional sccuracy of work piece.抄録全体を表示PDF形式でダウンロード (1403K) -
(II)接着剤で反射鏡を接着したエタロンについての測定例諸隈 肇1967 年 33 巻 394 号 p. 709-713
発行日: 1967/11/05
公開日: 2009/06/30
ジャーナル フリーThe wavelength of the light transmitted through an etalon of 20mm has been calibrated with two of the methods described in (I). The measured values coincide with each other to better than 1 × 10-7. The 20mm etalon is combined with a 2.3mm etalon to slice out a narrow spectral portion from a broad spectre of a high pressure mercury lamp. For the matching of the etalons, the shorter etalon is placed in an air tight chamber and its inside pressure is adjusted so that the intensity of the transmitted light becomes maximum. It is found that the effective wavelength varies with the inside pressure due to the imperfect flatness of the 20mm etalon. The stability of the etalon has been examined and it is found that the etalon is stable enough.抄録全体を表示PDF形式でダウンロード (843K) -
セラミックの砥粒加工(第4報)新井 湧三, 井田 一郎, 福田 満利, 鈴木 誠1967 年 33 巻 394 号 p. 714-720
発行日: 1967/11/05
公開日: 2009/06/30
ジャーナル フリーAs a basis of thread grinding on ceramic bobbins used for high frequency coils with a diamond wheel, the peculiarities in plain grinding are compared concerning grinding force, wear of abrasives, ground surface and grinding efficiency for steatite, forsterite and alumina. The results obtained are as follows: (1) Low grinding force and large stock removal are obtained in the case of a small work speed, say, 0.1m/min, (2) Wear is severe in grinding of alumina. When the wear percentage on the points of abrasives in area reaches to 2-3 %, grinding force increases with smaller stock removal, including the cases for other ceramics. (3) Steatite exhibits plastic flowed surfaces, the grinding of which is generally difficult in dry state. Alumina ground with sharp abrasives or forsterite have fractured surfaces, and the latter is far easier to be ground. (4) The grinding efficiencies are 1.5-2. 5 for alumina and 3.1-3.7 for forsterite when taking the efficiency as 1 for steatite.抄録全体を表示PDF形式でダウンロード (1450K) -
材料から見たガラスの研摩機構泉谷 徹郎, 原田 正一1967 年 33 巻 394 号 p. 721-727
発行日: 1967/11/05
公開日: 2010/02/16
ジャーナル フリーRelation between the polishing rate and physical and chemical properties of glasses was investigated on many kinds of optical glasses and the polishing mechanism of glass was discussed. The polishing rate of glass depends on the rate of forming the hydrated layer resulting from the chemical reaction between the polishing slurry and the glass surface and the hardness of the hydrated layer. Thus, the polishing mechanism of glass is considered as follows; the hydrated layers, resulting from the chemical reaction with polishing slurry, are scratched off and planed by the grains burned in the polisher.抄録全体を表示PDF形式でダウンロード (1198K) -
エネルギ伝達機構について西山 卯二郎, 井上 卓, 千田 豊満1967 年 33 巻 394 号 p. 728-734
発行日: 1967/11/05
公開日: 2009/06/30
ジャーナル フリーThis paper descrides the mechanism of the energy transmission for the deformation on the electrohydraulic forming. By the high speed photography, the first part of this study is intended to show that the gas energy is essential to deform the blank. In the second part, the importance of the gas energy is demonstrated by the experiments on the effects of the hydrostatic head. The most remarkable fact on the results of the experiments is that the deforming mechanism is devided into two stages. Thus, this study clears up the deforming mechanism of this forming, and indicates the effective method to utilize the gas energy.抄録全体を表示PDF形式でダウンロード (1014K) -
大野 正夫1967 年 33 巻 394 号 p. 735-745
発行日: 1967/11/05
公開日: 2009/06/30
ジャーナル フリーPDF形式でダウンロード (1761K) -
橋本 順次1967 年 33 巻 394 号 p. 746-751
発行日: 1967/11/05
公開日: 2009/06/30
ジャーナル フリーPDF形式でダウンロード (872K) -
1967 年 33 巻 394 号 p. 752
発行日: 1967/11/05
公開日: 2009/06/30
ジャーナル フリーPDF形式でダウンロード (181K) -
1967 年 33 巻 394 号 p. 753-758
発行日: 1967/11/05
公開日: 2009/06/30
ジャーナル フリーPDF形式でダウンロード (812K)
- |<
- <
- 1
- >
- >|