-
Article type: Cover
Pages
Cover1-
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
-
Article type: Index
Pages
Toc1-
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
-
Dapeng WANG, Toshiyuki KAWAHARAMURA, Chaoyang LI, Takashi HIRAO
Article type: Article
Session ID: IDY2011-1
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
The development of new and high efficient phosphor has been an important technology for the display industry. In order to overcome the remained problems of powder phosphor and lower the fabrication cost, we developed a novel technique for fabricating ZnO thin film phosphor on the glass substrate directly at the low temperature. This fabricated ZnO thin film phosphor has the promising features including higher coherency, uniformity, flatness regarding to the disadvantage of the power phosphor. Particularly, the ZnO thin film phosphor, showing high luminance of blue-green, was easily and precisely patterned on large area (φ100mm) by wet etching method.
View full abstract
-
Taku IGUCHI, Hiroko KOMINAMI, Yoichiro NAKANISHI, Kazuhiko HARA, Akima ...
Article type: Article
Session ID: EID2010-23
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
ZnAl_2O_4 phosphor which shows ultra violet emission under the electron beam excitation has been investigated for the ultra violet emitting devices. In this work, we investigated the dependence of structure and the luminescence of ZnAl_2O_4 phosphor on firing condition which prepared by solid-phase reaction. The structure and the luminescence properties of the ZnAl_2O_4 were drastically changed by the firing conditions (firing temperature, atmosphere, and ZnO/α-Al_2O_3 molar ratio, etc.). From the results of XRD, PLE and CL measurements, it is thought that ZnAl_2O_4 has a bandgap of about 7eV and the UV emission is caused by oxygen vacancy and the energy level caused by Zn excess in the crystal.
View full abstract
-
Takahisa YAMASAKI, Toshiaki SEINO, Hiroko KOMINAMI, Yoichiro NAKANISHI ...
Article type: Article
Session ID: EID2010-24
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
It is researched that low temperature preparing process of thin film phosphors by laser annealing. Using phosphor is SrGa_2S_4:Eu^<2+>. Preparing process is that Ga_2S_3:Eu (1mol%) and SrS:Eu (2mol%) pellets were evaporated by two electron beams, and deposited on substrates. After deposition, pre-annealing at 500℃ is carried out, then Nd:YAG (355nm) laser is irradiated. In this study, to consider the preparation mechanism of SrGa_2S_4:Eu^<2+> by 355nm laser annealing, spectral transmittance of SrS:Eu and Ga_2S_3:Eu thin films were measured, and simulation of thermal distribution was carried out. At 355nm, transmittance of SrS is higher than Ga_2S_3, and according to simulation result, it was guessed that Ga_2S_3 absorbed laser energy mainly and heated. SrGa_2S_4:Eu^<2+> thin films were prepared by 355nm laser at 10Hz change from 8kHz, to know the relationship between laser frequency and influence to preparation of thin film by laser annealing. On 10Hz laser annealed samples have very few luminance, and it was found that these are almost amorphous by XRD result. It is guessed that laser of low frequency can not obtain hearings on each pulse, due to wide pulse length.
View full abstract
-
Mamoru KITAURA, Rong-Jun Xie, Takashi TAKEDA, Naoto HIROSAKI, Akimasa ...
Article type: Article
Session ID: EID2010-25
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
In order to investigate the local structure of Mn^<2+> ions in bright oxynitride phosphors γ-AlON:Mn,Mg, electron spin resonance (ESR) measurements have been carried out at room temperature. The ESR spectra consist of six prominent peaks and five weak doublet structures. The former and latter correspond to allowed- and forbidden-transitions, respectively. The ESR spectrum measured is in good agreement with those due to Mn^<2+> ions in MgAl_2O_4 spinet, suggesting that Mn^<2+> ions are coordinated by four oxygen ions. An appearance of the doublet structures reveals that there is additional distortion around Mn^<2+> ions, resulting from the existence of two kinds of anions, namely, oxygen and nitrogen, and aluminum vacancies.
View full abstract
-
Takuro Murakawa, Hiroshi Okura, Tetsuo Honma, Yoshinobu Miyamoto, Kout ...
Article type: Article
Session ID: EID2010-26
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
In a phosphor synthesis of Y_3Al_5O_<12>:Ce (YAG:Ce) by a liquid phase reaction method, the state of Ce in precursors, intermediate products and completed phosphors are systematically investigated by X-ray Absorption Fine Structure (XAFS) measurement. It has been found out that Ce is initially trivalent in the precursor. However, most of Ce are oxidized and might be segregated as an amorphous tetravalent cerium oxide from the yttrium compounds by firing in air atmosphere. By contrast, Eu stably remains at Y sites as trivalent even fired in air atmosphere. It concludes that the redox activity of luminescent centers dominates the incorporation of them into host lattices.
View full abstract
-
Takahiro Koshiba, Yusuke Nakamura, Yoshinobu Miyamoto, Koutoku Ohmi
Article type: Article
Session ID: EID2010-27
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
CuAlS_2:Mn red phosphor thin films have been prepared by multi-source deposition method by combining two electron-beam-guns evaporation using Cu metal and Al_2S_3:Mn source pellets and H_2S supply. It has been found that the compositional ratio of sulfur is very little even for the thin films prepared with enough much H_2S supply. The fact implies that sulfur is not efficiently incorporated into thin films during the deposition. To compensate the lack of sulfur, Al_2S_3:Mn pellets mixed with additional sulfur have been used as a evaporation source. The prepared thin films show a X-ray diffraction peak due to the CuAlS_2 (112) plane. The films also show a reddish-orange photoluminescence (PL) due to CuAlS_2:Mn, and a PL excitation spectra originating from the band-edge absorption of CuAlS_2.
View full abstract
-
Ryo ISHIOKA, Kohei IGARASHI, Takeshi FUKUDA, Naoto KIJIMA, Norihiko KA ...
Article type: Article
Session ID: EID2010-28
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
Optical characterization of Ba_3Si_6O_<12>N_2Eu^<2+> (BSON) phosphor was carried out based on an internal quantum efficiency, photoluminescence (PL), and thermoluminescence (TL) measurements. Carrier trapping levels were detected by TL spectra, and thermal activation energy of each was determined by the relation between peak position and temperature gradient. An atmospheric annealing of the BSON phosphor increased the density of a carrier trapping level which corresponds to the secondary TL peak, and decreased the internal quantum efficiency. On the other hand, an annealing in a hydrogen atmosphere brought no increase in the density of the carrier trapping level, keeping high value of internal quantum efficiency.
View full abstract
-
Yudai Yamashita, Yoshinori Tawaratani, Yoshinobu Miyamoto, Koutoku Ohm ...
Article type: Article
Session ID: IDY2011-2
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
SrGa_2S_4:Eu shows a saturated green luminescence and is expected to be one of green EL phosphor materials. Since a high burning temperature is required to crystallize SrGa_2S_4, it is hard to form SrGa_2S_4:Eu phosphor thin films on cheap glass substrates with a low softening temperature. To solve this problem, in this study, SrGa_2S_4:Eu phosphor thin films have been attempted to prepared by spin-coating method using submicron phosphor particles. Relatively uniform and dense SrGa_2S_4:Eu phosphor layers with a thickness of 1-3μm have been achieved by spin-coating using the particles having an average diameter of about 1μm. The obtained EL devices show a green luminescence with CIE color coordinates of (x,y)=(0.23,0.72), and the luminance under 1kHz driving is about 200cd/m^2.
View full abstract
-
Shogo Horiguchi, Takuya Kontani, Masahiro Horita, Nobuyoshi Taguchi, Y ...
Article type: Article
Session ID: EID2010-29
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
A ZnS-based inorganic Electro-Luminescence (EL) has been widely studied for the next generation display and illumination. We have reported that the uniform emission is observed in the EL with ZnS:Cu powders sintered by the microwave (MW) heating. In this study, we investigated ZnS:Cu phosphors sintered by the infrared rapid thermal annealing (RTA) instead of the MW heating to clarify the mechanism.
View full abstract
-
Kazuki ITATANI, Hayato KAWASAKI, Toshihiko TOYAMA, Hiroaki OKAMOTO
Article type: Article
Session ID: EID2010-30
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
Current-voltage (J-V) measurements were performed on the top-emission EL devices with a printed emission layer involving solution-processed ZnO nanocrystals. The temperature dependence of J-V characteristics suggested the deposition method and the deposition conditions of top anodes play a crucial role in determining UV emission intensity.
View full abstract
-
Kouhei IGARASHI, Ryo ISHIOKA, Yusuke TSUKADA, Takeshi FUKUDA, Zentaro ...
Article type: Article
Session ID: EID2010-31
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
In order to improve the quality of AlGaN-based crystals for deep-UV light emission, we studied photoluminescence (PL) of four MOCVD-grown AlGaN quantum wells from standpoints of growth temperature and In incorporation. A growth at 880℃ with In flow was shown to be best among them based on the comparative measurements on PL spectra, temperature and excitation density dependence. With increasing excitation density, a saturation of nonradiative recombination centers takes place and increases internal quantum efficiency. A simplified rate-equation analysis yielded weak carrier density dependence of nonradiative recombination constant for each sample. Detailed optimization of growth condition with a minute In incorporation is promising for improving the internal quantum efficiency.
View full abstract
-
Toshiyuki KAWAHARAMURA, Hiroyuki ORITA, Takahiro SHIRAHATA, Takuto IGA ...
Article type: Article
Session ID: IDY2011-3
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
Magnesium oxide (MgO) thin film is useful as the protective film for plasma display and the antireflective film. Therefore, the development of method which can prepare the high quality MgO thin film with low utility cost and environment-friendly is very important. Currently, almost all of the fabrication methods of MgO thin film are the techniques operated with vacuum state. The reason is that the direct growth to the glass substrate is very difficult because the high temperature above 500℃ which is not suitable for glass substrate due to the near glass transition temperatures is necessary to prepare the MgO thin film under the atmospheric pressure. Then, we tried making MgO thin film on the glass substrate with mist deposition. Material oxide thin films such as zinc oxide, gallium oxide, tin oxide, indium oxide, ferric oxide, and so on, can be prepared at atmospheric pressure with mist deposition. In this conference, we report on the conditions and the preparations of MgO thin films.
View full abstract
-
Takayuki CHONAN, Baku KATAGIRI, Tohru KAWAKAMI, Tatsuo UCHIDA
Article type: Article
Session ID: IDY2011-4
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
Optical elements for display are required more complex control of the incident light, therefore measurements and evaluations of three-dimensional surface shape become more important. However conventional measurement methods of the surface shape can't measure samples with very flat surface or steep slope accurately. In this study, we try to measure three-dimensional shape with SEM more accurately by making fine pattern with scattering nanoparticles. As a result, we show the relation between the magnification of the nanoparticles and the accuracy of the measurement, and confirm the validity of the measurement.
View full abstract
-
Kanae TANIGUCHI
Article type: Article
Session ID: IDY2011-5
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
In recently, it is needs a new transform coding method to generate super-high-quality images in super-high-resolution display environment. I focus on the mosquito noise appeared by AC quantization error in AC frequencies for DCT and propose its quantification and noise evaluation. From the results, it has to set to quantization errors less than 13, 9, and 7 contrast to the edge nodes 2, 3, and 4, respectively. It was clear that WDCT to arrest divergence of AC frequencies by improving within frequency resolution is realizable to 19.59% mosquito noise of DCT.
View full abstract
-
Hiroshi Furuta, Toshiyuki Kawaharamura, Mamoru Furuta, Tokiyoshi Matsu ...
Article type: Article
Session ID: EDD-11-15
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
Carbon nanotube arrays are candidate for ideal electron emitters for high efficient field emission devices such as field emission display, field emission lamps and so on. Three types of carbon nanotube emitter arrays are discussed for (1) the screen printed in-plane triode CNT emitter array, (2) the pillar shaped CNT diode emitter, and (3) a novel short-length, and high-density CNT patterned emitter arrays.
View full abstract
-
Yasushi MOTOYAMA, Daisuke KATO, Masahiko SEKI
Article type: Article
Session ID: IDY2011-6
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
We were able to fabricate a PDP with an air-stable high-γ material Ca_<0.36>Mg_<0.64>O protective layer. The thickness of the CaCO_3 layer formed on the surface of the CaMgO protective layer during high-temperature process in air was reduced by a new deposition conditions and increasing the concentration of MgO in the CaMgO protective layer. The discharge voltage of the panel stabilizes at low values (V_f=161V, V_<s min>=112V) within 40h of aging; this duration is remarkably short for a high-γ protective layer under the air annealing process.
View full abstract
-
Tetsuo SAKAI, Kunihide Tachibana
Article type: Article
Session ID: EID2010-32
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
Fast addressing is essential for a high field frequency PDP. We analyzed the relation between addressing delay time T and initial number of electrons n_0 in a Ne filled cell with MgO protective layer, and found that the variation of ?T was mainly caused by the ?-action. If n_0=16, ?T becomes very small with the miss addressing rate less than 10^<-10>. This condition is realized if there are projection parts on the MgO layer.
View full abstract
-
Tsutomu KONDO, Takahiro ISHINABE, Tetsuya MIYASHITA, Tatsuo UCHIDA
Article type: Article
Session ID: IDY2011-7
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
Improvement of the optical performance of polarizer has become important problem for the improvement of brightness and contrast ratio of liquid crystal displays. Analysis of complex refractive index of polarizer and understanding of its influence to the optical characteristic of liquid crystal display is important in the design of the efficient polarizer. In this paper, we devised new method for analyzing the complex refractive index of polarizer accurately by ellipsometry, and clarified its influence to the optical characteristic of the liquid crystal display.
View full abstract
-
Hideo Kawano
Article type: Article
Session ID: EDD-11-19
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
The higher mobility causes to promote flicker by increasing recharge effect in TFT LCD. At that case, field through voltage must be set less than two-thirds of the case with conventional a-Si TFT. Then, reducing parasitism capacitance between gate and source in TFT is useful method without reducing Vgh. To achieve it, self-alignment TFT should be introduced to the LCD with high mobility TFT like as TAOS TFT.
View full abstract
-
Rumiko Yamaguchi, Masaki Ikeya
Article type: Article
Session ID: EID2010-33
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
Polyvinyl-cinnamate (PVCi) is well known as a photo crosslinkable polymer to align liquid crystal (LC) molecules by a linearly polarized UV (LPUV) light exposure. In addition, it has been recognized that the easy axis is perpendicular to the rubbing direction, since sidechains of PVCi are oriented perpendicular to the main chains. However, we found that MBBA (N-p-methoxybenzylidene p-n-butylaniline) aligns parallel to the rubbing direction. In this study, the in-plane easy axis of LCs with different chemical structures has been investigated on the rubbed PVCi surface. We reported that LCs with and without polar groups aligned perpendicular and parallel to a rubbing direction on a rubbed PVCi surface, respectively. Easy axis control of the PVCi was realized by mixing LCs and an alignment patterning was successfully demonstrated on crosslinked and uncrosslinked surfaces by exposing with and without unpolarized UV light.
View full abstract
-
Kazuma SAKAKIBARA, Chiharu SUZUKI, Tomokazu SHIGA
Article type: Article
Session ID: EID2010-34
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
An adaptive dimming technique reduces the power consumption and also improves the picture quality. However the technique causes streaky image degradation when the LCD is viewed from an angle. In this study, the visibility of sinusoidal-shaped pattern having various contrasts and frequencies is evaluated. It is found from the evaluation result, the degradation is not annoying when the width of backlight luminance distribution is 0.7 times wider than the width of dimming segment.
View full abstract
-
Tokiyoshi Matsuda, Mamoru Furuta, Takahiro Hiramatsu, Hiroshi Furuta, ...
Article type: Article
Session ID: EID2010-35
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
Insulating SiO_x film was deposited at low temperature with newly developed plasma source for low heat resistive substrate as for flexible display. The plasma was induced with electromagnetic field generated by two facing electrodes including magnets inside and covered with SiO_2 targets. The higher deposition rate was realized with the mixture of tetramethylsilane and oxygen as source gases. The insulating properties were obtained as 3×10^<-8>A/cm^2 at an electric field of 1MV/cm, and a breakdown voltage of 5MV/cm at 1×10^<-6>A/cm^2 for the film deposition rate at 11nm/min. High density plasma enhanced by magnetic field would be the hopeful solution for deposition of high deposition rate gate insulator at low temperature.
View full abstract
-
Yoshiki NAKAJIMA, Tatsuya TAKEI, Yoshihide FUJISAKI, Toshihiro YAMAMOT ...
Article type: Article
Session ID: IDY2011-8
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
We have developed a transfer technology to fabricate a flexible organic TFT (OTFT) backplane for a large-area and high-resolution flexible display. The OTFT backplane, which was formed on a glass substrate with a temporary adhesive layer, was composed of gate electrodes, polymer gate dielectrics, source/drain electrodes, an organic semiconductor layer and pixel electrodes. After formation of passivation layer and bonding of a plastic film on the surface of the backplane, it was peeled off the glass substrate. The electrical characteristics of the OTFT backplane were evaluated, before and after the backplane was transferred. We have confirmed that a transfer technology is effective in fabricating flexible displays.
View full abstract
-
Atsuyuki Shimizu, Keita Kanbe, Yasufumi Iimura
Article type: Article
Session ID: EID2010-36
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
Today, an organic thin film transistor (O-TFT) is known to become a key element for realizing high-performance flexible display devices due to its low process temperature, which is essential for using flexible plastic substrates. In this study, we have directed our attention to a gate insulator, which are one of indispensable elements for O-TFTs. Here we choose a UV-curable liquid crystalline polymer as a gate insulating material, and we study its conducting properties with observing deep carrier trap levels (DTL) of the film by the thermal stimulated current (TSC) method.
View full abstract
-
Takahiro MIYAZAKI, Masaaki INATOMI, Yasufumi IIMURA
Article type: Article
Session ID: EID2010-37
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
Organic light-emitting diodes (OLEDs) has been recognized to show superior display characteristics to other display modes such as wide viewing angle, fast response and thin-and-light weight, and so various research works on the topic have been conducted aiming at their wide applications to flexible displays, flat illumination sources, and so on. However, OLEDs have still remained several problems such as lifetime and emission efficiency of the device and it is essential to improve these properties for further expanding of the application fields. In this study, we have reported the emission properties of OLEDs with various shaped hetero-interface structures and proved the insertion of an appropriate mixed layer to be very effective to improve the device performance.
View full abstract
-
Keitaro FURUSHO, Reiji HATTORI, Sang-Gun LEE
Article type: Article
Session ID: EID2010-38
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
In order to clarify the electrical conductivity mechanism in the organic semiconductor, the current-voltage theoretical equations in single-layered organic semiconductor device were established and evaluated by comparing with the measurement results on the practical device. Two types of theoretical equations were established and discussed based on the injection-limited and space-charge-limited currents. It was also discussed that the temperature and thickness dependences of the theoretical equation were corresponding to the experimental result well.
View full abstract
-
Munenori KOGA, Reiji HATTORI, Michihiro ASAKAWA
Article type: Article
Session ID: EID2010-39
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
We discussed the application of multi-line driving which can increase the duty ratio rather than the line-by-line driving method to passive-matrix driven organic light emitting display (PMOLED) in order to reduce the luminance deterioration. To drive the plural OLEDs in the same luminance, the voltage driving is preferred to the current driving, but the voltage driving causes another non-uniform luminance problem due to the voltage drop on the electrode. To solve this problem, some calculated values which can compensate the luminous non-uniformity were added to the input data. This method was estimated with a practical panel.
View full abstract
-
Kyuwon Kyoung, Katsunori Yuge, Yohei Yumisashi, Reiji Hattori
Article type: Article
Session ID: EID2010-40
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
We proposed the novel capacitive type touch panel consisting of several electrodes with one-dimensional structure, which enables a multi touch operation and realizes a high transparency owing to a single layer. We also investigated the capacitive sensing circuit. The production costs can be reduced than a conventional projected capacitive type touch panel by simplifying the structure of the touch panel. And also multi touch function that is limited at surface capacitive type touch panel is realized.
View full abstract
-
Fumio Okano, Masaru Kanazawa, Yuichi Kusakabe, Yasuyuki Haino, Masato ...
Article type: Article
Session ID: IDY2011-9
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
A scanning method based on complementary field offset sampling is proposed. It improves the resolution of RGB video projectors with a square grid pixel structure. We position the pairs of the red (R) and blue (B) pixels at a diagonal offset of one-half the pixel pitch from the green (G) pixels, alternating the position of the G pixels and the pair pixels for each field. The Nyquist frequency in both horizontal and vertical directions is doubled. The method also reduces flicker compared to methods with G, R, and B pixels at the same location and alternating at the same time. A Super Hi-vision projector was developed by this scanning method.
View full abstract
-
Tatsuki INUZUKA
Article type: Article
Session ID: IDY2011-10
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
RGBW LCD panel has superiority on transparency characteristic. However, signal conversion is necessary, because subpixel layout is different from conventional RGB signal. To solve this problem, we have developed a new signal processing method based on pattern-matching and color-conversion to meet the demands for low cost and low power dissipation.
View full abstract
-
Yohei YUMISASHI, Reiji HATTORI
Article type: Article
Session ID: EID2010-41
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
One of the methods to differentiate an electronic paper (e-Paper) display from others display is to make the shape of e-Paper thin, light and flexible just like a paper. Many display panels with such a shape have already demonstrated, but actual e-Paper devices are still thick, heavy and inflexible. In order to realize the real e-Paper device, we have been developing an original wireless power transfer system which uses the field coupling, and discussed a device which has no battery, no large memory.
View full abstract
-
R. Sato, B. Katagiri, Y. Suzuki, M. Kano, T. Uchida
Article type: Article
Session ID: IDY2011-11
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
Recently, wide variety of displays have been developed and are practically applied. Among them front projection displays have several features such as relatively large screen capability, high luminance and compact projector system. However, it has important problem of contrast reduction in a bright environment. We proposed a new front projection system for large screen by diffusing only projected light towards the viewing angle range and reflecting ambient light towards the other angle ranges. With this system, we realized a high quality and large size front projection display with a high contrast ratio even in a bright room.
View full abstract
-
Yasuko ANDOH, Shiro OZAWA, Kazuyuki ISO, Takafumi MUKOUCHI, Norihiko M ...
Article type: Article
Session ID: EID2010-42
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
DFD (Depth fused 3D) displays consist of two electronic display screens stacked in the direction of depth to show three-dimensionality. Front and rear screen images are produced by sharing the luminance of a 2D image depending on its depth. Displaying computer graphic (CG) images in real time has been and is still easy, because such images have the depth of information used to distribute the rendering luminance. However, since there is no depth information in photographed images, it has been difficult to display them three-dimensionally in real time. This report presents our results in displaying 3D photographed images to a DFD display system in real time using depth information from a range imaging camera.
View full abstract
-
Tatsuya SUGITA, Atsushi KISHIOKA, Makoto SASAKI, Yasuhisa SHIRAISHI, S ...
Article type: Article
Session ID: IDY2011-12
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
We developed a novel lenticular lens, whose edge lines were modulated with a sinusoidal form, for a luminance enhanced LCD to reduce moire fringe between lenses and prism sheets and demonstrated the moire reduction to about 1/5 with the developed wobbled lenticular tens formed by a printing method.
View full abstract
-
Article type: Appendix
Pages
App1-
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
-
Article type: Appendix
Pages
App2-
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
-
Article type: Appendix
Pages
App3-
Published: January 21, 2011
Released on J-STAGE: September 21, 2017
CONFERENCE PROCEEDINGS
FREE ACCESS
